Abstract:The application of Li-ion conducting garnet electrolytes is challenged by their large interfacial resistance with the metallic lithium anode and the relative small critical current density at which the lithium dendrites short-circuit the battery. Both of these challenges are closely related to the morphology and the structure of the garnet membranes. Here, we prepared four polycrystalline garnet Li6.4La3Zr1.4Ta0.6O12 (LLZTO) pellets with different particle sizes (nano/micro) and grain boundary additive (with/without Al2O3) to investigate the influence of grain size, the composition of the grain boundary, and the mechanical strength of the pellet on the total Li-ion conduction of the pellet, Li/garnet interfacial transfer, and lithium dendrite growth in all-solid-state Li-metal cells. The results showed that the garnet pellets prepared with nanoparticles and LiAlO2-related grain boundary phase had decreased total Li-ion conductivity because of the increased resistance of the grain boundary; however, these pellets showed higher mechanical strength and improved capability to suppress lithium dendrite growth at high current densities. By controlling the grain size and optimizing the grain boundary with Al2O3 sintering additive, the hot-pressing sintered LLZTO solid electrolytes can reach up to 1.01 × 10–3 S cm–1 in Li+ conductivity and 0.29 eV in activation energy. LLZTO with nanosized grain and LiAlO2-modified grain boundary showed the highest critical current density, which is 0.6 mA cm–2 at room temperature and 1.7 mA cm–2 at 60 °C. This study offers a useful guideline for preparing a high-performance LLZTO solid electrolyte.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c18674?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c18674</a>.Feature sizes of LLZTO powders prepared by hand milling and sand milling (Table S1); XRD patterns of hot-pressing sintered samples (Figure S1); element distribution on the polished surface of the sintered samples containing Al2O3 and without Al2O3 by EDX scan (Figure S2); equivalent circuit model for EIS fitting (Figure S3); and LLZTO specimens fractured by three-point bending test, gold sprayed on the surface of the micro-solid electrolyte, an optical photo of the micro-lithium symmetrical battery, and a micro-test fixture designed to test the micro-battery (Figure S4) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c18674/suppl_file/am0c18674_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Preparation and Performance of Highly-Conductive Dual-Doped Li7La3Zr2O12 Solid Electrolytes for Thermal Batteries

Preparation of LiLaZrMO (M= Ga/Al) Solid Electrolytes for Thermal Batteries

Enhanced Al/Ta Co-Doped Li7La3Zr2O12 Ceramic Electrolytes with the Reduced Ta Doping Level for Solid-State Lithium Batteries

Preparation and performances of gallium-doped LLZO electrolyte with high ionic conductivity by rapid ultra-high-temperature sintering

Realizing Li7La3Zr2O12 garnet with high Li+ conductivity and dense microstructure by Ga/Nb dual substitution for lithium solid-state battery applications

Interfacial Modification of Ga-Substituted Li7La3Zr2O12 Against Li Metal Via a Simple Doping Method

Phase Evolution, Structure, and Electrochemical Performance of Al-, Ga- and Ta- Substituted Li7La3Zr2O12 Ceramic Electrolytes by a Modified Wet Chemical Route

Improvement of Ionic Conductivity in Li7La3Zr2O12 (LLZO) Solid Electrolyte By Doping with Aluminum/Tungsten

Ga-doped lithium lanthanum zirconium oxide electrolyte for solid-state Li batteries

Experimental and Theoretical Study on Enhanced Electrochemical Properties of Double Doped Garnet-Type Solid Electrolyte

A Low-Cost Al-doped Garnet Li7La3Zr2O12 with High Ionic Conductivity for High-Energy Solid-State Lithium Metal Batteries

Amorphous Dual‐Layer Coating: Enabling High Li‐Ion Conductivity of Non‐Sintered Garnet‐Type Solid Electrolyte

Enhanced Ionic Conductivity and Excellent Lithium Stability of Garnet-Type Li6.55Ga0.15La3Zr2O12 Solid-State Electrolytes by Magnesium Doping

Defect chemistry engineering of Ga-doped garnet electrolyte with high stability for solid-state lithium metal batteries

Enhanced Performance of Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 Solid Electrolyte by the Regulation of Grain and Grain Boundary Phases

Crystal Structure and Preparation of Li7La3Zr2O12 (LLZO) Solid-State Electrolyte and Doping Impacts on the Conductivity: An Overview

Effect of Sintering Temperature and Holding Time on Ionic Conductivity for Li6.4La3Zr1.4Ta0.6O12 Electrolyte

Developing Preparation Craft Platform for Solid Electrolytes Containing Volatile Components: Experimental Study of Competition between Lithium Loss and Densification in Li7La3Zr2O12

Co-doping strategy enhanced the ionic conductivity and excellent lithium stability of garnet-type Li7La3Zr2O12 electrolyte in all solid-state lithium batteries

Experimental and Computational Study of Mg and Ta‐Doped Li7La3Zr2O12 Garnet‐Type Solid Electrolytes for All‐Solid‐State Lithium Batteries