Abstract:The coarse segregative eutectic phases, emerged in the twin roll casting (TRC) process of Mg strips, which cannot be resolved solely by controlling the processing variables or post heat treatment, are detrimental to the subsequent rolling deformation. Considering it, we introduce the pre-rolling steps on the TRC Mg-4Al-2Sn-1 Zn (ATZ421) alloys, which is expected to facilitate the dissolution of these segregative phases by increasing distortion of crystal lattices and rolling stress, and further investigate the effect of a single pass or two passes pre-rolling on the microstructure evolution and tensile properties. It indicates that the pre-rolled alloy with two passes presents more uniform precipitates and higher twinning density in comparison with that using a single pass. The uniform distribution of precipitates in two passes pre-rolling is due to the increase in density of dislocations and deformed twins, which results in more distortion of crystal lattices with more stored energy, facilitating the diffusion of solutes. Moreover, the pre-rolling of two passes introduces more rolling stress into Mg matrix, which is beneficial for the crush of coarse eutectic phases, and further accelerates the sufficient dissolution of second phases. After the subsequent rolling and annealing processes, the sheet with pre-rolling deformation of two passes shows finer microstructure, which mainly benefits from the pinning effects of uniform nano-sized precipitates. As a result, the annealed sheet with two-pass pre-rolling deformation exhibits an advantageous combination of high strength and high ductility with fine microstructure, showing an ultimate tensile strength of similar to 297 MPa, a yield strength of similar to 205 MPa and an elongation of 25.0%. This work provides an effective method of dissolving the coarse segregative phases in the TRC Mg alloys with significant potential for industrial production.

Strengthening of Duplex Mg-9Li-3Al-2Zn-1Sn Alloy by Solid Solution and Mixed Rolling-Induced Second Phase Transition

Improving the mechanical properties of duplex Mg-Li-Zn alloy by mixed rolling processing

Strengthening of Mg-Li Alloy Dominated by Continuously Hardened Mg Phase During Room Temperature Rolling

Microstructure Evolution and Strengthening Mechanism of Dual-Phase Mg–8.3Li–3.1Al–1.09Si Alloys during Warm Rolling

Mechanical Properties and Microstructural Evolution in a Superlight Mg-6.4Li-3.6Zn-0.37Al-0.36Y Alloy Processed by Multidirectional Forging and Rolling

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Simultaneously Improving Strength and Ductility of Mg−3Li−8Gd−2Y−1.5Ag Alloy by Solution Treatment and Hot‐Rolling Process

Effect of Rolling Strain on Microstructure and Tensile Properties of Dual-Phase Mg–8Li–3Al–2Zn–0.5Y Alloy

An investigation on annealing process and strengthening mechanism of cold rolled Mg-10Li-3Al-2.8Zn alloy

Spheroiding and Refining of Coarse CaMgSn Phase in Mg–Al–Sn–Ca Alloys for Simultaneously Improved Strength and Ductility Via Sub-Rapid Solidification and Controlled Rolling

A Rolled Mg‐8Al‐1Sm‐1Zn Alloy with High Strength‐Ductility via Single‐Pass Liner Rolling

Microstructure and Tensile Properties of Rolled Mg-4Al-2Sn-1Zn Alloy with Pre-Rolling Deformation

Microstructure Evolution and Mechanical Properties of High-Strength Mg-Gd-Y-Zn-Mn Alloy Processed by Asymmetric Hot Rolling

Enhancing Strength-Ductility Synergy and Corrosion Residual Strength of Hot-Rolled Mg-2Zn-0.85Y Alloy

Microstructure, Texture and Mechanical Properties of Mg-Sn-Zn Alloy Sheets Processed by Extrusion and Hot Rolling

Effects of Extrusion and Rolling Processes on the Microstructure and Mechanical Properties of Zn-Li-Ag Alloys

Enhanced Mechanical Properties of Extruded Mg–Y–Zn Alloy Fabricated Via Low-Strain Rolling

Microstructure and Mechanical Properties of Mg–6Al–1Sn–0.3Mn Alloy Sheet Fabricated Through Extrusion Combined with Rolling

Microstructure and Mechanical Properties of Mg–6Li–xAl–0.8Sn Alloys

Microstructure And Mechanical Properties Of Duplex Structured Mg-Li-Zn-Y Alloys

Effect of Hot-Rolling on Microstructures and Mechanical Properties of Extruded Mg-6gd-3.2y-Xzn-0.5zr Sheet