Abstract:The microstructure and mechanical properties of as-extruded Mg-1.0Sn, Mg-1.0Sn-0.5Zn, Mg-1.0Sn-0.7Ca and Mg-1.0Sn-0.5Zn-0.5Ca (all in wt%) alloy sheets were investigated and compared at room temperature. The results showed that the Mg-1.0Sn and Mg-1.0Sn-0.5Zn alloys exhibited relatively coarse grains and typical strong basal textures, whereas the Mg-1.0Sn-0.7Ca and Mg-1.0Sn-0.5Zn-0.5Ca alloys showed obvious grain refinement and weakened extrusion direction (ED)-split textures. The yield strength and ductility of the Mg-1.0Sn-0.5Zn alloy increased by approximately 20 MPa and 5%, respectively, than that of the Mg-1.0Sn alloy. Despite the similar ductilities of the Mg-1.0Sn-0.5Zn and Mg-1.0Sn-0.7Ca alloys, the yield strength improvement was more remarkable in the Mg-1.0Sn-0.7Ca alloy. In particular, the yield strength of the Mg-1.0Sn-0.7Ca alloy in tension along transverse direction was 209 MPa, which was about 73 MPa higher than that of the Mg-1.0Sn alloy. This was attributed mainly to the grain refinement from similar to 26 mu m to similar to 9 mu m and the precipitation strengthening induced by homogeneous distributed, spherical Mg2Ca nano-particles. Furthermore, ductility of the Mg-1.0Sn-0.5Zn-0.5Ca alloy in tension along the ED could reach up to 30.5%, which was almost twice that of the Mg-1.0Sn-0.7Ca alloy, because of increased activation of prismatic slip, enhanced grain boundary cohesion and improved intergranular strain propagation capacity. Therefore, individual addition of dilute Zn or Ca contributed to an improvement in the strength and ductility of the Mg-1.0Sn alloy, whereas combined addition of dilute Zn and Ca provided a new approach for achieving excellent ductility of the Mg-1.0Sn alloy.

Microstructure, Texture and Mechanical Properties of Mg-Sn-Zn Alloy Sheets Processed by Extrusion and Hot Rolling

A Comparison of Microstructure and Mechanical Properties of Mg–9Al–1Zn Sheets Rolled from As-Cast, Cast-Rolling and As-Extruded Alloys

Microstructures and mechanical properties of as-extruded Mg–5Sn–1Zn–xAl (x=1, 3 and 5) alloys

Microstructure Evolution and Mechanical Properties of Extruded Mg-Al-Zn-Sn Alloy Sheets

Effect of Zn on microstructure and mechanical property of Mg–3Sn–1Al alloys

Microstructure and Mechanical Properties of Mg–6Al–1Sn–0.3Mn Alloy Sheet Fabricated Through Extrusion Combined with Rolling

Effects of Zn Addition on the Microstructure, Tensile Properties and Formability of As-Extruded Mg-1Sn-0.5Ca Alloy

Effects of Zn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg-2Al-0.5Ca Alloy

Effects of Zn/Al Mass Ratio on Microstructure Evolution and Mechanical Properties of Mg–Sn Based Alloys

Microstructure and Mechanical Property of High Strength Mg–Sn–Zn–Al Alloys

Microstructure and Mechanical Properties of Mg–Al–Sn Extruded Alloys

Effects of Zn and Ca Addition on Microstructure and Mechanical Properties of As-Extruded Mg-1.0Sn Alloy Sheet

Study on Bulk Texture and Mechanical Properties of As-Extruded Wide Mg-Al-Zn Alloy Sheets with Different Al Addition

Effect of Cu/Zn on Microstructure and Mechanical Properties of Extruded Mg–Sn Alloys

Microstructure and Mechanical Properties of As-Extruded and As-Aged Mg–Zn–Al–Sn Alloys

Enhanced Mechanical Properties of Extruded Mg–Y–Zn Alloy Fabricated Via Low-Strain Rolling

Effect of Zn Addition on Microstructure and Mechanical Properties after Extrusion, Rolling and Ageing in Mg-9Gd-3Y-0.5Zr Alloys

Effect of Zn Content on the Microstructure and Mechanical Properties of Mg–Al–Sn–Mn Alloys

Study on Microstructure and Mechanical Properties of Hot Rolled Mg97Zn1Y2 Alloy Sheet

Study on Microstructure and Properties of Single‐Pass Online Heating Rolling of Mn‐Containing Magnesium Alloy Sheets

Microstructures and Mechanical Properties of As-Extruded and Heat Treated Mg–6Zn–1Mn–4Sn–1.5Nd Alloy