Abstract:Scanning probe microscopy was used to simultaneously determine the molecular chain structure and intrinsic mechanical properties, including anisotropic elastic modulus and friction, for lamellae of highly oriented high-density polyethylene (HDPE) obtained by the melt-drawn method. The molecular-scale image of the highly oriented lamellae by friction force microscopy (FFM) clearly shows that the molecular chains are aligned parallel to the drawing direction, and the periodicities along and perpendicular to the drawing direction are 0.26 and 0.50 nm, respectively. The results indicate that the exposed planes of the lamellae resulting from the melt-drawn method are (200), which is consistent with results of transmission electron microscopy and electron diffraction. Because of the high degree of anisotropy in the sample, coming from alignment of the molecular chains along the drawing direction, the measured friction force, F, determined by FFM is strongly dependent on the angle, theta, between the scanning direction and the chain axis. The force increases as theta is increased from 0 degrees (i.e., parallel to the chain axis) to 90 degrees (i.e., perpendicular to the chain axis). The structural anisotropy was also found to strongly influence the measurements of the transverse chain modulus of the polymer by the nanoindentation technique. The measured value of 13.8 GPa with transverse modulus was larger than the value 4.3 GPa determined by wide-angle X-ray diffraction, which we attributed to anisotropic deformation of the lamellae during nanoindentation measurements that was not accounted for by the elastic treatment we adopted from Oliver and Pharr. The present approach using scanning probe microscopy has the advantage that direct correlations between the nanostructure, nanotribology, and nanomechanical properties of oriented samples can be determined simultaneously and simply.

Fabrication and Mechanical Characterization of Highly Preferentially Oriented Montmorillonite Thin Films

Extracting Hydromechanical Properties of Montmorillonite Quasi-Crystals Via Nanoindentation of Oriented Thin Films

Growth Mechanism of a Preferentially Oriented Mordenite Membrane

Oriented Zeolite Mfi Monolayer Films on Metal Substrates by in Situ Crystallization

Wet Grinding of Montmorillonite and Its Effect on the Properties of Mesoporous Montmorillonite

Fabrication and Characterization of the Orientated Mmt/Pi Composite Films Via Relatively Low Magnetic Field

A Facile Fabrication of Highly B-Oriented Mfi Zeolite Films in the Teos-Tpaoh-H2o System Without Additives

Thermal processing of zeolite seed layers for the fabrication of compact oriented MFI zeolite films

Montmorillonite Exfoliation in LLDPE and Factors Affecting Its Orientation: From Monolayer to Multi-Nano-Layer Polymer Films

Nanostructure and Mechanical Measurement of Highly Oriented Lamellae of Melt-Drawn HDPE by Scanning Probe Microscopy

Preparation of Aluminosilicate Ferrierite Zeolite Nanosheets with Controllable Thickness in the Presence of a Sole Organic Structure Directing Agent

Polypropylene/montmorillonite nanocomposites I. Preparation, characterizsation and dynamic mechnical properties

Fabrication of Oriented Nano-/Meso-porous MOF Thin Films Via Fluid-Assisted Technique

Facile processing of oriented macro-porous ceramics with high strength and low thermal conductivity

Micromechanical Properties of Nanostructured Clay-Oxide Multilayers Synthesized by Layer-By-Layer Self-Assembly

The Preparation and Characterization of the PZT Thin Film with (100) Peak Preferred Orientation

Preparation of Montmorillonite Nanosheets with a High Aspect Ratio Through Heating/Rehydrating and Gas-Pushing Exfoliation.

Interfacial Modification of Magnetic Montmorillonite (MMT) Using Covalently Assembled LbL Multilayers

Laminar mesoporous structure of modified montmorillonite clays and its formation mechanism

Atomistic study on thermo-mechanical behavior and structural anisotropy of montmorillonite under triaxial tension and compression

Effect of Montmorillonite on Orientation of Drawn Polypropylene Films