Optimizing the Broadband Source-Driven Resonant Fiber-Optic Gyroscope

Shuang Liu,Junyi Hu,Yuxin Wang,Hewei Wang,Lu Liu,Huilian Ma

DOI: https://doi.org/10.1364/ofs.2023.th6.47

2023-01-01

Abstract:We optimized the fiber-optic ring resonator used in the broadband source-driven resonant fiber-optic gyroscope and reported the latest gyroscope test results with bias stability ranging from 1°/h to 450µ°/h when using different fiber coil lengths.

What problem does this paper attempt to address?

Closed-loop Resonant Fiber-Optic Gyroscope Based on a Broadband Source

Shuang Liu,Junyi Hu,Lu Liu,Qingwen Liu,Huilian Ma,Zuyuan He

DOI: https://doi.org/10.1109/icocn55511.2022.9901145

2022-01-01

Abstract:This paper presents a closed-loop resonant fiber-optic gyroscope with a broadband source. In the experiment, a bias stability of 0.008°/h is successfully demonstrated with a 100m-long fiber-optic ring resonator of 7.6 cm diameter.
Navigation-grade Resonant-Fiber Optic Gyroscope with a Broadband Source

Huilian Ma,Shuang Liu,Junyi Hu,Lu Liu,Yuxin Wang,Hewei Wang

DOI: https://doi.org/10.1364/cleo_si.2023.sf1h.1

2023-01-01

Abstract:We report a broadband source-driven resonant-fiber optic gyroscope with 0.0029°/h 1/2 angle random walk and 0.0063°/h bias stability when using a 100-meter-long fiber-optic ring resonator of 7.6 cm diameter.
Improving the Performance of Broadband Source-Driven Resonant Fiber-Optic Gyroscopes

Shuang Liu,Junyi Hu,Yuxin Wang,Hewei Wang,Lu Liu,Huilian Ma

DOI: https://doi.org/10.1109/jlt.2024.3402236

IF: 4.7

2024-01-01

Journal of Lightwave Technology

Abstract:The broadband source-driven resonant fiber-optic gyroscope (RFOG), as a new type of gyroscope, demonstrates impressive advantages in both detection sensitivity and long-term bias stability. To further improve the system performance, this paper investigates the factors affecting the detection sensitivity and long-term bias stability of the broadband source-driven RFOG. Two mathematical models are developed to analyze the relationship between the fiber-optic ring resonator (FRR) parameters and the detection sensitivity, as well as the error induced by imperfect modulation signals. The analysis shows that the detection sensitivity can be improved by optimizing the coupling coefficients of the FRR. Meanwhile, the bias error at the output of the gyroscope caused by imperfect modulation can be effectively suppressed by improving the harmonic suppression ratio of the modulation signal and compensating the phase difference between the first and second harmonics. Finally, after using the optimized FRR and suppressing the error due to imperfect modulation, the experimental results show that the bias stability is in the range of 1°/h to 450μ°/h for different cavity lengths.
A Hollow-Core Photonic-Crystal Fiber-Optic Gyroscope Based on a Parallel Double-Ring Resonator.

Heliang Shen,Kan Chen,Kang Zou,Yijia Gong,Ran Bi,Xiaowu Shu

DOI: https://doi.org/10.3390/s21248317

IF: 3.9

2021-01-01

Sensors

Abstract:A novel system structure of resonant fiber optical gyroscope using a parallel double hollow-core photonic crystal fiber ring resonator is proposed, which employs the double closed loop and reciprocal modulation–demodulation technique to solve the problem of the length mismatch between rings. This structure can suppress the residual amplitude modulation noise and laser frequency noise, essentially eliminating the influence of the Rayleigh backscattering noise and dramatically reduce the Kerr-effect-induced drift by three orders of magnitude. Thanks to its excellent noise suppression effect, the sensitivity of this novel system can approach the shot-noise-limited theoretical value of 8.94 × 10−7 rad/s assuming the length of the fiber ring resonator is 10 m.
Compact Resonant Fiber-Optic Gyroscope with a Broadband Light Source

Junyi Hu,Shuang Liu,Qianqian Wang,Huilian Ma

DOI: https://doi.org/10.1364/ofs.2023.th6.48

2023-01-01

Abstract:A compact broadband source-driven resonant fiber-optic gyroscope prototype is assembled and tested. The angle random walk is 0.0037°/√h and bias stability is 0.0069°/h for a 175-m long fiber coil of 5.7 cm diameter.
Performance of a Resonant Fiber-Optic Gyroscope Based on a Broadband Source

Shuang Liu,Lu Liu,Junyi Hu,Hanzhao Li,Qingwen Liu,Huilian Ma,Zuyuan He

DOI: https://doi.org/10.1364/ao.460419

IF: 1.9

2022-01-01

Applied Optics

Abstract:A resonant fiber-optic gyroscope (RFOG) based on a broadband source can avoid the fundamental drawback of coherence detection processing while possessing the greater sensitivity afforded by the finesse of the fiber-optic ring resonator. In this paper, the basic operation principle is presented and demonstrated in detail, and various noise sources, as well as the temperature effect encountered in this broadband source-driven RFOG, are studied and analyzed. Then a combined modulation technique is proposed to suppress the residual backscattering noise. To further reduce the effect of temperature transience, an asymmetric fiber ring resonator is designed. In the experiment, a bias stability of 0.01°/h is successfully demonstrated with a 100 m-long fiber ring resonator of 8 cm diameter in a laboratory environment without temperature control.
Principle and Application of High Dynamic Fiber Gyroscope

Lei WANG,Xing-fan CHEN,Cheng LIU,Xiao-wu SHU

DOI: https://doi.org/10.3969/j.issn.1009-086x.2017.06.001

2017-01-01

Abstract:A method for designing a high dynamic fiber optic gyroscope (FOG) is presented for a class of high spinning carrier with demand of accuracy and range.It is fulfilled by identification of fringes to detect phase error beyond[-π,+ π] with the dynamic range over 40 000 (°)/s,which provides a new simple,effective and high reliability scheme for light of sight (LOS) stabilization and attitude control of navigation systems.
Closed-Loop Resonant Fiber-Optic Gyroscope with a Broadband Light Source

Junyi Hu,Shuang Liu,Lu Liu,Huilian Ma

DOI: https://doi.org/10.1109/jlt.2023.3270443

IF: 4.7

2023-01-01

Journal of Lightwave Technology

Abstract:The resonant fiber-optic gyroscope (RFOG) with a broadband light source has recently emerged as an attractive new type optical gyroscope. However, the use of a broadband source limits the linear dynamic range and worsens the scale factor accuracy. In this article, the closed-loop scheme of the broadband source-driven RFOG is proposed and demonstrated. First, a novel method called the period-stacking method is presented. Then the closed-loop mechanism of the broadband source system is revealed. Although the rotation-induced frequency difference is wavelength-dependent in the broadband source scheme, we are pleased to find that the frequency shift generated by the serrodyne modulation is wavelength-independent and can be used to compensate for the rotation information. Finally, a closed-loop broadband source-driven RFOG with a 100 m-long and 7.6 cm-diameter fiber-optic ring resonator is experimentally demonstrated. The measured result shows that the long-term bias stability of the closed-loop broadband source-driven RFOG is 0.0063 °/h over a test time of up to 500 minutes. The temperature dependence drops from 2.8 (°/h)/°C in the open-loop system to 0.54 (°/h)/°C. It is improved by a factor of 5.2. The open-loop linear detection range of ±50 °/s is improved to ±350 °/s. It is improved by a factor of 7. The open-loop scale factor nonlinearity of 8% is decreased to 0.0281% (281 ppm), which is improved by a factor of 285.
Broadband Source-Driven Resonant Micro-Optic Gyroscope Based on a Multi-Turn Waveguide-Type Ring Resonator

Shuang Liu,Junyi Hu,Yuxin Wang,Qingwen Liu,Huilian Ma,Zuyuan He

DOI: https://doi.org/10.1364/ol.479092

2023-01-01

Abstract:The resonant micro-optic gyroscope (RMOG) is one of the most promising candidates for chip-scale optoelectronic gyroscopes. A broadband source-driven RMOG based on a multi-turn waveguide-type ring resonator (WRR) has been proposed and demonstrated. The theoretical sensitivity is enhanced with the multi-turn structure, while the parasitic backscattering can be resolved by the use of the broadband source, thus greatly improving the long-term bias stability of the RMOG. We also reduce the relative intensity noise (RIN)-induced error of the broadband source at the gyro output by optimizing the number of loop turns of the WRR, and improve the angle random walk (ARW) by 4.8 dB compared with the case of a single-turn WRR. Finally, a bias stability of 1°/h is obtained with a 5-turn WRR of 4.05 cm diameter, achieving the tactical-grade resolution. To the best of our knowledge this is the best result reported to date for an RMOG of similar size.
Resonant Fiber Optical Gyroscope Using the Single-Mode Fiber Ring Resonator.

Lu Liu,Shuang Liu,Weiwen Qian,Hanzhao Li,Huilian Ma

DOI: https://doi.org/10.1364/ao.429941

IF: 1.9

2021-01-01

Applied Optics

Abstract:This paper provides a scheme for realizing high-accuracy, low-cost resonant fiber optical gyroscopes (RFOGs) with single-mode (SM) fibers. The temperature-related polarization noise, which deteriorates the bias stability of the RFOG, has been suppressed thanks to a much longer birefringence beat length of SM fibers. It is also helpful to improve the theoretical sensitivity of the RFOG because of the very low loss of the SM fiber components. A transmissive 39-m-long SM fiber ring resonator (FRR) is fabricated. The measured finesse is 58.7, and its total loss is calculated to be less than 0.3 dB. Using this SM-FRR as the sensing element, an RFOG is then set up that achieves an angular random walk of 0.0039∘/√h and a bias stability of 0.05°/h. The experimental results show that the SM-FRR scheme would be a good candidate for producing high-accuracy and low-cost RFOGs.
Optimization of Reciprocal Modulation Parameters in Resonant Fiber Optic Gyro

Kang Zou,Lei Wang,Kan Chen,Ran Bi,Xiaowu Shu

DOI: https://doi.org/10.1109/jlt.2021.3090989

IF: 4.7

2021-01-01

Journal of Lightwave Technology

Abstract:The resonant fiber optic gyro (RFOG) based on reciprocal modulation-demodulation technique is introduced and the influence of high modulation frequency on resonance and demodulation output is analyzed. The expression of backscattering output in resonant cavity is deduced and the experimental device is built to measure the backscattering coefficient. The demodulation model considering backscattering noise is established under reciprocal sinusoidal modulation, and the optimal modulation parameters are obtained by simulation. Finally, the RFOG system is set up. The results show that the detection sensitivity is improved by 19% with the optimal modulation parameters and the system bias stability improves from 0.067°/s to 0.023°/s.
Development of the Resonant Fiber Optic Gyroscope Prototype

Lu Liu,Weiwen Qian,Shuang Liu,Junyu Tu,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1109/icocn53177.2021.9563715

2021-01-01

Abstract:This paper presents latest progress in the development of a packaged resonant fiber optic gyroscope prototype with a single semiconductor laser, which achieves a bias stability of 0.14°/h and an angle random walk of 0.05 °/ vh.
Performance Improvement of White-Light-driven Resonant Fiber Optic Gyroscope Using Four-Frequency Sawtooth Wave Modulation Technology

Fan Wu,Jun Li,Shiqi Lan,Bo Yan,Jun Zhou,Yazhou Yue

DOI: https://doi.org/10.1016/j.optcom.2023.129827

IF: 2.4

2024-01-01

Optics Communications

Abstract:In this study, a novel resonant fiber optic gyroscope (RFOG) that relies on four-frequency sawtooth wave modulation technology is proposed. This innovative approach is utilized to demodulate both the light intensity changes of the optical system and the half-wave voltage drift of the multi-functional integrated optical chip (MIOC). The principle of modulation is expounded, and a simulation model is established to evaluate the performance of the system. We conducted synchronous compensation of the bias drift, which is caused by the light intensity changes, and applied closed-loop control to MIOC modulation frequency-shift voltage, effectively reducing the scale factor error. As a result, the system achieved a bias instability (BI) of 0.0055°/h, with a 500 m-long fiber-optic ring resonator (FRR) of 6 cm diameter, at room temperature. Furthermore, the scale factor error was reduced by more than threefold in the temperature range of −40 °C to 70 °C. These results demonstrate the superior performance of the proposed RFOG and its potential for high-precision navigation and other applications.
Performance Improvement of a Resonant Fiber Optic Gyroscope with a Hybrid Photonic Crystal Fiber Ring Resonator.

Yi Lin,Hanzhao Li,Huilian Ma,Lin Ma

DOI: https://doi.org/10.1364/ao.58.007424

IF: 1.9

2019-01-01

Applied Optics

Abstract:The photonic crystal fiber (PCF) with better thermal stability and polarization-maintaining performance is applied to the resonant fiber optic gyroscope (RFOG). A hybrid fiber ring resonator is fabricated using the conventional polarization-maintaining fiber (PMF) and PCF with close mode field diameters (MFDs) to reduce MFD-mismatch-induced splicing loss. Furthermore, the temperature-dependent birefringence coefficients of the PMF and the PCF are measured to differ almost four times in absolute value and be opposite in sign. The polarization stability of the hybrid PCF-PMF ring resonator is improved by a factor of 7 compared with the PMF ring resonator with the same length of PMF. The RFOG equipped with this hybrid PCF-PMF ring resonator achieves a bias stability of 1.67°/h.
Research Progress of the Resonant Fiber Optic Gyroscope Technology

Linglan Wang,Yuchao Yan,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1117/12.2197580

2015-01-01

Abstract:The resonant fiber optic gyro (RFOG) is a high accuracy inertial rotation sensor based on the Sagnac effect. The existence of various noises, including the nonreciprocal noises such as the polarization noise and the Kerr noise as well as the reciprocal circuit noise, limits the performance improvement of the RFOG. An improved scheme by inserting two in-line polarizers in the polarization maintaining fiber transmission-type resonator has been proposed to suppress the polarization-fluctuation induced drift. Furthermore, the adoption of the air-core photonic bandgap fibers (PBFs) offers a novel solution to reduce the optical Kerr effect. In addition, A digital signal processor is designed to reduce the reciprocal noises and detect the rotation information. A minimum actual rotation of 0.001°/s is achieved. The dynamic range is improved by a factor of 7 and the scale factor nonlinearity is decreased by a factor of 60.
Triple Closed-Loop Resonant Fiber Optic Gyroscope

Junyu Tu,Hanzhao Li,Sen Ye,Huilian Ma

DOI: https://doi.org/10.1109/ICOCN.2019.8934119

2019-01-01

Abstract:To improve the reciprocity of the signal processing systems, a triple closed-loop resonant fiber optic gyroscope is proposed. Enhanced long-term and thermal bias stabilities are successfully demonstrated thanks to the reciprocal configuration.
Reduction of relative intensity noise in a broadband source-driven RFOG using a high-frequency modulation technique

Shuang Liu,Lu Liu,Junyi Hu,Qingwen Liu,Huilian Ma,Zuyuan He

DOI: https://doi.org/10.1364/OL.470933

IF: 3.6

2022-01-01

Optics Letters

Abstract:A broadband source-driven resonant fiber-optic gyroscope (RFOG) can reduce coherence-related noise, thus achiev-ing a better sensitivity with a much simpler configuration than the traditional system with a coherent source. Its detection sensitivity, however, is still limited by the excess relative intensity noise (RIN) of the broadband source. In this paper, the RIN error mechanism in this broadband source-driven RFOG is revealed and countermeasures are presented. We demonstrate that the use of a high-finesse fiber-optic ring resonator and a high-frequency modulation -demodulation technique can reduce the RIN-induced error. It is indicated that the optimal modulation parameters can provide a RIN-induced error reduction of 6.1 dB, allowing the broadband source-driven RFOG to operate near the shot-noise-limited theoretical sensitivity. With the optimal high-frequency modulation-demodulation technique, an angle random walk of 0.0013 degrees/root h is achieved with a 200-m -long fiber-optic ring resonator of 7.6 cm diameter. This is the best result reported to date, to the best of our knowledge, for fiber-optic gyroscopes of this size. (C) 2022 Optica Publishing Group
Hybrid Single-Polarization Fiber Ring Resonator and Implications for Resonant Fiber Optic Gyro

Yuchao Yan,Linglan Wang,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/acpc.2014.aw3d.3

2014-01-01

Abstract:A novel hybrid single-polarization fiber ring resonator is demonstrated for reducing the polarization error in a resonant fiber optic gyro. A bias stability below 0.7°/h with an integration time of 100 s has been carried out.
Resonant fiber optic gyroscope driven by a broadband light source based on an over-coupled state fiber ring resonator

Kai Xu,Yanru Zhou,Fanyan Xue,Yulin Wang,Wenyao Liu,Jun Tang,Jun Liu

DOI: https://doi.org/10.1364/ao.525243

IF: 1.9

2024-06-13

Applied Optics

Abstract:Kai Xu, Yanru Zhou, Fanyan Xue, Yulin Wang, Wenyao Liu, Jun Tang, Jun Liu The resonant fiber optic gyroscope (RFOG) driven by a broadband light source has advantages over conventional RFOGs in terms of structure, ... [Appl. Opt. 63, 4840-4847 (2024)]

optics
Resonant Fiber Optic Gyro Based on A Sinusoidal Wave Modulation and Square Wave Demodulation Technique

Linglan Wang,Yuchao Yan,Huilian Ma,Zhonghe Jin

DOI: https://doi.org/10.1364/ao.55.003274

IF: 1.9

2016-01-01

Applied Optics

Abstract:New developments are made in the resonant fiber optic gyro (RFOG), which is an optical sensor for the measurement of rotation rate. The digital signal processing system based on the phase modulation technique is capable of detecting the weak frequency difference induced by the Sagnac effect and suppressing the reciprocal noise in the circuit, which determines the detection sensitivity of the RFOG. A new technique based on the sinusoidal wave modulation and square wave demodulation is implemented, and the demodulation curve of the system is simulated and measured. Compared with the past technique using sinusoidal modulation and demodulation, it increases the slope of the demodulation curve by a factor of 1.56, improves the spectrum efficiency of the modulated signal, and reduces the occupancy of the field-programmable gate array resource. On the basis of this new phase modulation technique, the loop is successfully locked and achieves a short-term bias stability of 1.08°/h, which is improved by a factor of 1.47.

Optimizing the Broadband Source-Driven Resonant Fiber-Optic Gyroscope

Closed-loop Resonant Fiber-Optic Gyroscope Based on a Broadband Source

Navigation-grade Resonant-Fiber Optic Gyroscope with a Broadband Source

Improving the Performance of Broadband Source-Driven Resonant Fiber-Optic Gyroscopes

A Hollow-Core Photonic-Crystal Fiber-Optic Gyroscope Based on a Parallel Double-Ring Resonator.

Compact Resonant Fiber-Optic Gyroscope with a Broadband Light Source

Performance of a Resonant Fiber-Optic Gyroscope Based on a Broadband Source

Principle and Application of High Dynamic Fiber Gyroscope

Closed-Loop Resonant Fiber-Optic Gyroscope with a Broadband Light Source

Broadband Source-Driven Resonant Micro-Optic Gyroscope Based on a Multi-Turn Waveguide-Type Ring Resonator

Resonant Fiber Optical Gyroscope Using the Single-Mode Fiber Ring Resonator.

Optimization of Reciprocal Modulation Parameters in Resonant Fiber Optic Gyro

Development of the Resonant Fiber Optic Gyroscope Prototype

Performance Improvement of White-Light-driven Resonant Fiber Optic Gyroscope Using Four-Frequency Sawtooth Wave Modulation Technology

Performance Improvement of a Resonant Fiber Optic Gyroscope with a Hybrid Photonic Crystal Fiber Ring Resonator.

Research Progress of the Resonant Fiber Optic Gyroscope Technology

Triple Closed-Loop Resonant Fiber Optic Gyroscope

Reduction of relative intensity noise in a broadband source-driven RFOG using a high-frequency modulation technique

Hybrid Single-Polarization Fiber Ring Resonator and Implications for Resonant Fiber Optic Gyro

Resonant fiber optic gyroscope driven by a broadband light source based on an over-coupled state fiber ring resonator

Resonant Fiber Optic Gyro Based on A Sinusoidal Wave Modulation and Square Wave Demodulation Technique