Abstract:With the rapid development of industrial manufacturing, additive manufacturing has attracted extensive attention in the industry since it possesses a high material utilization rate. Friction stir additive manufacturing (FSAM) is a novel solid-phase additive manufacturing method which possesses the advantage of achieving excellent mechanical properties of FSAM of aluminium alloy components. The formation characteristic of the additive zone and thermal processes in FSAM significantly determine the mechanical properties of the FSAM components. However, there is still a lack of quantitative analysis of the thermal processes in FSAM of AA2024-T4 aluminium alloy. Thus, a finite element model (FEM) of FSAM was proposed, and the element birth-death technology was employed to capture the addition of an additive layer during the FSAM process. The evolution of the thermal field in FSAM was quantitatively studied by the model. The formation characteristics and mechanical properties of the additive components were analyzed. It indicates that the volume of the additive zone increases with an increase in the tool rotation speed, while it decreases with an increase in the transverse speed during FSAM. The height and width of the hook structure decrease with an increase in the transverse speed. The tensile strength of the FSAM component first increases with the increase in the transverse speed and reaches its maximum value at the transverse speed of 90 mm/min, while further increases in the transverse speed reduce the tensile strength. The peak temperature of the first layer is the highest during the whole FSAM process. While the peak temperate of subsequent additive layers is about 475 °C, which is lower than the first layer and remains almost constant. The maximum value of the thermal cycle decreases with an increase in the tool's transverse speed. While the high-temperature residence time increases with a decrease in the tool transverse speed. The model is validated by comparing the predicted heat-affected zone with the experimentally measured ones. It lays a solid foundation for optimizing the friction stir additive manufacturing process to improve manufacturing efficiency and enhance the performance of the built components.

Microstructure Evolution and Mechanical Property Enhancement of Friction Stir Additive Manufactured Ti6Al4V Alloy

Restirring and Reheating Effects on Microstructural Evolution of Al–Zn–Mg–Cu Alloy during Underwater Friction Stir Additive Manufacturing

The simulation of microstructural evolutions in friction stir additive manufacturing

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Investigation on microstructural evolution and property variation along building direction in friction stir additive manufactured Al–Zn–Mg alloy

Experimental and numerical analysis of friction stir additive manufacturing of 2024 aluminium alloy

Microstructure Evolution and Grain Refinement in 2319 Aluminium Alloy Via Wire Arc Additive Manufacturing Coupled with Multi-Pass Friction Stir Processing

Quantitative study on the correlation between microstructure and mechanical properties of additive friction stir deposited

Microstructure and mechanical properties of friction stir processed TA5 alloy

A Critical review on the performance and microstructural characteristics of materials fabricated through friction stir additive methods and deposition techniques

Evaluation of Microstructural, Mechanical and Corrosion Behaviours of Laminated AA6061/AA7075 Metal Matrix Composites Build by Friction Stir Additive Manufacturing for Structural Applications

Investigation on Fractographic and Microstructure Evolution in AA7075/ZrO2/G Multilayer Laminated Composite Fabricated Using Friction Stir Additive Manufacturing Process

Multi-objective optimization of friction stir additively manufactured Al-7075 multi-layered laminates

Refined microstructure and enhanced mechanical performance of hybrid additive manufacturing Al-Cu-Mg alloys by multi-cycle friction stirring processing

Friction stir additive manufactured AA 6061/TiC/GS composite: assessment of microstructural and mechanical properties

Parametric Influence of Friction Stir Processing on Microstructural Evolution and Tensile Behavior of AZ31/Ti-6Al-4V Magnesium Matrix Composites

Effect of Rotational Shear and Heat Input on the Microstructure and Mechanical Properties of Large-Diameter 6061 Aluminium Alloy Additive Friction Stir Deposition

Interface and Properties of the Friction Stir Welded Joints of Titanium Alloy Ti6Al4V with Aluminum Alloy 6061

Ultrasonic-induced amorphization and strengthening mechanisms of ultrasonic vibrations assisted friction stir Al/Ti welds

Microstructure evolution, phase formation, corrosion, and mechanical properties of stainless steel fabricated by extrusion-based sintering-assisted additive manufacturing

Microstructure-deformation relationship of additive friction stir-deposition Al–Mg–Si