Abstract:Publication date: 10 January 2022 Source: Solid State Phenomena Vol. 327 Author(s): Jiehua Li, Maria Pammer, Ernst Neunteufl, Peter Schumacher AZ80 alloy has been widely used to produce high performance Mg casting and wrought parts for high-end applications due to its high mechanical properties and deformation ability. However, at least two important issues still need to be solved in order to further improve its mechanical properties and deformation ability. Firstly, the grain size of α-Mg in AZ80 alloy is relatively large (more than 1000 μm) due to a lack of efficient grain refinement methodologies. Secondly, the size of the eutectic Mg17Al12 phase is also large and the distribution of the eutectic Mg17Al12 phase is continuous, which is very harmful for the mechanical properties, in particular to elongation. In this paper, these two important issues are investigated by adding Mg3N2 sub-micron particle into AZ80 alloy and thereby refining the α-Mg and the eutectic Mg17Al12 phase. Firstly, the Mg3N2 sub-micron particle was directly added into AZ80 alloy by using mechanically stirring in the semi-solid state, subsequently the melting temperature was increased above the liquidous temperature, and finally the melting was casted in the liquid state. It was found that the grain size of α-Mg can be refined from 883.8 μm to 169.9 μm. More importantly, the eutectic Mg17Al12 phase was also refined and the distribution became discontinuous. It should be noted that directly adding the Mg3N2 sub-micron particle into AZ80 alloy leads to a great loss of the Mg3N2 sub-micron particle due to the weak wetting behavior between the Mg3N2 sub-micron particle and Mg melt. The second methodology through mixing Mg3N2 sub-micron particles with AZ91 chips using a twin extruder was also used to prepare AZ91 master alloy with 3wt.% Mg3N2 sub-micron particle, which was subsequently added into AZ80 alloy in the liquid state. In this way, a significant grain refinement of α-Mg and a simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy was also achieved. The grain size of α-Mg can be refined from 883.8 μm to 325.9 μm. However, no significant grain refinement by using UST was observed. Instead, the grain size increases from 325.9 μm to 448.6 μm, indicating that the Mg3N2 sub-micron particle may lose its grain refinement potency due to possible aggregation and clustering. This paper provides an efficient and simple methodology for the grain refinement of α-Mg and the simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy.

Nanocrystalline AZ91 Alloy: Preparation, Exceptional Thermal Stability and Enhanced Hardness

Developing a high-speed-extruded BMZQ5100 alloy with higher strength and microstructural thermal stability than AZ91 alloy

Effect of Ti addition on the thermal stability of nanocrystalline AZ61 Mg alloy

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Microstructure and mechanical properties of Mg–Al based alloy with calcium and rare earth additions

The Control of Nbb2 Particles in Al-Nbb2 Master Alloy and its Effect on Grain Refinement of Az91 Magnesium Alloy

AZ91D/TiB2 Nanocomposites Fabricated by Solidification Nanoprocessing

The behaviour of AZ91 magnesium-based alloy with Ni–Al 2 O 3 reinforcement

Microstructure and Mechanical Properties of the AlCrFeCoNip/AZ91D Composites After Heat Treatment

Al-CeO2-Mg refiner on grain refinement, cast fluidity and mechanical properties of AZ91 alloy

Microstructure and Properties of Az91d Alloy with Ca Additions

AZ91 alloy nanocomposites reinforced with Mg-coated graphene: Phases distribution, interfacial microstructure, and property analysis

Effect of annealing treatment on the microstructure and mechanical properties of bulk nanostructured Ti/AZ61 composites prepared by hot pressing

Synthesis of Nanocrystalline AZ91 Magnesium Alloy Dispersed with 15 vol.% Submicron SiC Particles by Mechanical Milling

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

High Corrosion-Resistance Nanocrystalline Ni Coating on AZ91D Magnesium Alloy

Nano-ZnO Particles’ Effect in Improving the Mechanical Response of Mg-3Al-0.4Ce Alloy

Surface Grain Refinement of AZ91D Magnesium Alloy by Cold Spraying Shot Peening Process

Mechanical properties and fabrication of carbon nanotubes reinforced AZ91D magnesium matrix nanocomposites

Effect of the Mg3N2 Sub-Micron Particle on the Grain Refinement of AZ80 Alloy

Nanocrystallization and precipitation behavior evolution of AZ80 magnesium alloy during multi-directional compression