Abstract:In this study, a hot isostatic pressing (HIP) manufactured SiC particles (SiC p ) reinforced high alloyed Al–Zn–Mg–Cu–Zr–Ti aluminum matrix composite was fabricated through ball-milling, HIP, homogenization, hot extrusion, solution treatment, and aging treatment. The results showed the presence of an interfacial reaction layer, MgAl 2 O 4 , around the SiC p , which enhanced the bonding between the particles and the matrix. The aging treatment resulted in the formation of different aging precipitates, which were featured by GP zone for T4, GP zone + η' (metastable MgZn 2 ) + η (stable MgZn 2 ) for T6 and GP zone + η' (metastable MgZn 2 ) for T6I4. The composite samples of T4, T6, and T6I4 exhibited different mechanical properties. Specifically, the elastic modulus was measured as 102.9, 103.4, and 102.3 GPa, the yield strength was 685.3, 598.1, and 619.7 MPa, the ultimate tensile strength was 713.6, 618.9, and 633.3 MPa, and the elongation was 2.2%, 1.8%, and 2.8%, respectively. Furthermore, the corrosion behavior of the composite was evaluated through electrochemical, intergranular corrosion, and exfoliation corrosion. The corrosion current density was found to be 3.17 × 10 −7 , 4.97 × 10 −7 , and 3.67 × 10 −7 A cm −2 , the corrosion potential was measured as −0.70, −0.81, and −0.56 V, and the maximum intergranular corrosion depth was 139.9, 167.8, and 106.2 μm for T4, T6, and T6I4, respectively. The severity of exfoliation corrosion varied, with T4 showing severe pitting, T6 exhibiting moderate pitting, and T6I4 displaying slight pitting. The strengthening mechanism and load transfer strengthening of the composites were discussed in detail based on theoretical calculations, and the anti-corrosion mechanisms were also analyzed.

Microstructure and Mechanical Properties of the AlCrFeCoNip/AZ91D Composites After Heat Treatment

Effect of Heat Treatment on Microstructure and Mechanical Properties of Squeeze Cast n SiCp/AZ91D Magnesium Matrix Composites

The aging behavior, microstructure and mechanical properties of AlN/AZ91 composite

Microstructural Evolution and Interfacial Characterization of Al18B4O33w/GWZ1031K Magnesium Matrix Composite During Heat Treatment

Heat Treatable Al‐Zn‐Mg‐Cu Matrix Composites Reinforced With Ni‐Based Metallic Glass Powder

Microstructure and Mechanical Properties of an Al–Ni–Co Intermetallics Reinforced Al Matrix Composite

Microstructure and High-Temperature Mechanical Properties of CrMnFeCoNi/TiAl Composites Prepared by Powder Metallurgy

Effects of Heat Treatment on the Interface Microstructure and Mechanical Properties of Friction-Stir-Processed AlCoCrFeNi/A356 Composites

Effect of heat treatment on the microstructure, mechanical properties and fracture behaviors of ultra-high-strength SiC/Al–Zn–Mg–Cu composites

Nanocrystalline Ti/AZ61 Magnesium Matrix Composite: Evolution of Microstructure and Mechanical Property During Annealing Treatment

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing

Effect of heat treatment on the microstructure and properties of CoCrFeNiMo0.2 particles reinforced titanium matrix composites

Microstructure, Mechanical Properties and Fracture Mechanism of Ti2AlC Reinforced AZ91D Composites Fabricated by Stir Casting

Effects of Heat-Treatment on Interfacial Microstructures and Tensile Properties of Znal2o4 and Zno Coated Al18b4o33 W/Al Composites

Microstructural Evolution and Increased High-Temperature Tensile Strength of Extruded and Aged AlN/Al Reinforced Mg-10Gd-3Y-1Zn Composites

Mechanical Property Enhancement for Al Based Metal Matrix Composites

Effect of annealing treatment on the microstructure and mechanical properties of bulk nanostructured Ti/AZ61 composites prepared by hot pressing

Regulating microstructure and mechanical properties of the as-cast Mg-4Zn-0.5Y-0.5Nd alloy by heat treatment

Microstructure and properties of a HIP manufactured SiC p reinforced high alloyed Al–Zn–Mg–Cu–Zr–Ti aluminum matrix composite

Microstructure Characteristics and Compressive Properties of NiAl-based Multiphase Alloy During Heat Treatments

Effect of heat treatment on microstructure and mechanical properties of Cu–6.9Ni–2.97Al–0.99Fe–1.06Mn alloy