Abstract:Publication date: 10 January 2022 Source: Solid State Phenomena Vol. 327 Author(s): Jiehua Li, Maria Pammer, Ernst Neunteufl, Peter Schumacher AZ80 alloy has been widely used to produce high performance Mg casting and wrought parts for high-end applications due to its high mechanical properties and deformation ability. However, at least two important issues still need to be solved in order to further improve its mechanical properties and deformation ability. Firstly, the grain size of α-Mg in AZ80 alloy is relatively large (more than 1000 μm) due to a lack of efficient grain refinement methodologies. Secondly, the size of the eutectic Mg17Al12 phase is also large and the distribution of the eutectic Mg17Al12 phase is continuous, which is very harmful for the mechanical properties, in particular to elongation. In this paper, these two important issues are investigated by adding Mg3N2 sub-micron particle into AZ80 alloy and thereby refining the α-Mg and the eutectic Mg17Al12 phase. Firstly, the Mg3N2 sub-micron particle was directly added into AZ80 alloy by using mechanically stirring in the semi-solid state, subsequently the melting temperature was increased above the liquidous temperature, and finally the melting was casted in the liquid state. It was found that the grain size of α-Mg can be refined from 883.8 μm to 169.9 μm. More importantly, the eutectic Mg17Al12 phase was also refined and the distribution became discontinuous. It should be noted that directly adding the Mg3N2 sub-micron particle into AZ80 alloy leads to a great loss of the Mg3N2 sub-micron particle due to the weak wetting behavior between the Mg3N2 sub-micron particle and Mg melt. The second methodology through mixing Mg3N2 sub-micron particles with AZ91 chips using a twin extruder was also used to prepare AZ91 master alloy with 3wt.% Mg3N2 sub-micron particle, which was subsequently added into AZ80 alloy in the liquid state. In this way, a significant grain refinement of α-Mg and a simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy was also achieved. The grain size of α-Mg can be refined from 883.8 μm to 325.9 μm. However, no significant grain refinement by using UST was observed. Instead, the grain size increases from 325.9 μm to 448.6 μm, indicating that the Mg3N2 sub-micron particle may lose its grain refinement potency due to possible aggregation and clustering. This paper provides an efficient and simple methodology for the grain refinement of α-Mg and the simultaneous refinement of the eutectic Mg17Al12 phase in AZ80 alloy.

Surface Grain Refinement of AZ91D Magnesium Alloy by Cold Spraying Shot Peening Process

Preparation and properties of nano ZrO2 coating on magnesium alloy

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Nanocrystallization and precipitation behavior evolution of AZ80 magnesium alloy during multi-directional compression

Enhanced Electrochemical and Tribological Properties of AZ91D Magnesium Alloy via Cold Spraying of Aluminum Alloy

Preparation And Properties Of Cold Sprayed Nano Wc-17co Coating On Magnesium Alloy

A study of the corrosion behavior of AZ31 Mg alloy in depth direction after surface nanocrystallization

Effect of the Mg3N2 Sub-Micron Particle on the Grain Refinement of AZ80 Alloy

Nanofeatures Induced by Severe Shot Peening (SSP) on Magnesium Alloy AZ31

A study on the tribological behavior of AZ31 magnesium alloy sheets processed by temperature-assisted ultrasonic shot peening

Microstructure and Characterization of Surface Nanocrystallization of Aluminum Alloy

Surface Nanocrystallization Mechanism of a Rare Earth Magnesium Alloy Induced by HVOF Supersonic Microparticles Bombarding

Microstructure and improved anti-corrosion properties of cold-sprayed Zn coatings fabricated by post shot-peening process

Enhanced Corrosion Resistance of AZ91 Magnesium Alloy Through Refinement and Homogenization of Surface Microstructure by Friction Stir Processing

Electroless Ni–P deposition plus zinc phosphate coating on AZ91D magnesium alloy

Improving the Surface Friction and Corrosion Resistance of Magnesium Alloy AZ31 by Ion Implantation and Ultrasonic Rolling

Synthesis of Nanocrystalline AZ91 Magnesium Alloy Dispersed with 15 vol.% Submicron SiC Particles by Mechanical Milling

Influence of Zinc Chloride Exposure on Microstructure and Mechanical Behavior of Age-Hardened AZ91 Magnesium Alloy

A Simple Surface Treatment for Mg to Gain Enhanced Resistance to Corrosion and Corrosive Wear by Hammering Al Powder‐Covered Mg Substrate

Nanocrystallization of interfacial microstructure of deformed particles in cold sprayed Ti6Al4V deposits

Enhancement in microstructural and mechanical performance of AA7075 aluminum alloy via severe shot peening and ultrasonic nanocrystal surface modification