Abstract:Mesoporous carbon materials with ultra-thin carbon pore walls and highly dispersed Ni nanoparticles have been successfully prepared by using two different SBA-15 silicas as hard templates and 2,3-dihydroxynaphthalene (DHN) as a carbon precursor. The nickel precursor was a concentrated nickel nitrate hexahydrate [Ni(NO3)(2)center dot 6H(2)O] solution in 2-propanol, which was added to the carbon-silica nanocomposite prior to thermal treatment. The samples studied were analyzed by thermogravimetry (TG), nitrogen adsorption at -196 degrees C, powder X-ray diffraction (XRD), Raman spectroscopy, scanning and transmission electron microscopy (STEM), and in situ electron diffraction X-ray spectroscopy (EDX). While TG analysis revealed carbon contents lower than 30 wt.-%, nitrogen adsorption provided information about the homogeneity of the carbon thin film deposited onto the mesopore walls of the ordered silica templates SBA-15. The templates, carbon-silica nanocomposites, and carbon inverse replicas with nickel nanoparticles exhibit uniform pores, high surface areas, and large pore volumes. Partially graphitic carbon was identified by the presence of a characteristic G band in the Raman spectra, whereas the diffraction peak attributed to the stacking of graphene planes was not observed by powder XRD. The presence of ordered domains in the carbon materials studied was confirmed by small angle XRD and STEM imaging. In addition, the STEM images revealed that the nickel nanoparticles are uniform in size, ca. 3 nm, and are homogeneously dispersed on the tubular carbon walls. A few larger clusters of nickel, ca. 60 nm, present on the external surface, were identified by powder XRD as metallic Ni. The in situ EDX revealed that the small nanoparticles are largely composed of Ni with traces of NiO. Similar nanoparticle dispersions have been reported only for Ni-containing multiwalled carbon nanotubes (CNTs), whereas previously reported ordered mesoporous carbon materials, CMK-3, possess larger Ni/NiO nanoparticles. ((C) Wiley-VCH Verlag GmbH & Co. KGaA, 69451 Weinheim, Germany, 2009)

New and Facile Method of Multiwall Carbon Nanotubes Synthesis on 3d Nickel Surface: Characterization by Various Techniques and Comparison with Available Methods

Innovative multiwall carbon nanotubes synthesis on 3D nickel surface: a comparative study

Mesoporous Carbon Materials with Ultra‐Thin Pore Walls and Highly Dispersed Nickel Nanoparticles

Growth Of High-Quality Single-Wall Carbon Nanotubes Without Amorphous Carbon Formation

Synthesis Of Nickel Nanoparticles And Carbon Encapsulated Nickel Nanoparticles Supported On Carbon Nanotubes

A New Method to Fabricate Large Amount of Single-Walled Carbon Nanotubes

ChemInform Abstract: State of the Art of Single‐Walled Carbon Nanotube Synthesis on Surfaces

Thin-Film Metal Catalyst For The Production Of Multi-Wall And Single-Wall Carbon Nanotubes

Synthesis of multi-walled carbon nanotubes on nichrome and nickel by using rapid thermal processing furnace

An Efficient Method to Produce Single-Walled Carbon Nanotubes by Round-Trip Arc Discharge

Synthesis Of Large Quantity Single-Walled Carbon Nanotubes By Arc Discharge

A Catalytic-Assembly Solvothermal Route to Multiwall Carbon Nanotubes at a Moderate Temperature

mocapillary fl ow to purify single-walled carbon nanotubes

In situ growth of N-doped carbon nanotubes from the products of graphitic carbon nitride etching by nickel nanoparticles

Synthesis of Well-Aligned Multiwalled Carbon Nanotubes on Ni Catalyst Using Radio Frequency Plasma-Enhanced Chemical Vapor Deposition

Synthesis of Multi-Walled Carbon Nanotubes via Flame

Characterizing Multi-Walled Carbon Nanotube Synthesis for Field Emission Applications

Ferromagnetic Behaviour of Nickel Contacted Multiwalled Carbon Nanotubes

Coating of Carbon Nanotube with Nickel by Electroless Plating Method

Fabrication and growth mechanism of Ni-filled carbon nanotubes by the catalytic method

Synthesis,Characterization and Performance of Helical Carbon Nanotubes