Abstract:Cold metal transition (CMT) arc additive manufacturing (CMT-AM) technology can rapidly fabricate large-scale components, but encounters the challenges in improving efficiency, accuracy, and mechanical properties. Fortunately, oscillating laser-arc hybrid additive manufacturing (O-LHAM) provides a promising solution by stabilizing the arc at high current or high-speed, effectively addressing these issues. However, most studies primarily focus on thin-walled parts rather than entities, which are fabricated using multi-layer and multi-pass processes. The microstructure and mechanical properties vary with deposition strategies and greater heat accumulation. This paper therefore investigates the effects of deposition strategies on the formation, microstructure, and tensile properties of 100 mm × 100 mm × 70 mm O-LHAMed entities with a maximum feeding speed of 18 m/min. It is found that employing a continuous reciprocating deposition strategy without arc extinguishing within the same layer effectively avoids the mismatch between the actual and designed shape. At this stage, the deposition efficiency can reach 848 cm 3 /h, which is 2.25 times that of CMT-AMed parts reported in the literature. Deposition strategies do not affect the microstructures of different cross-sections of the entities. However, using multiple high currents facilitates the effect of solution heat treatment, leading to a transition in crystal solidification from ferrite-austenite mode in thin-walled parts to fully austenite mode, and ferrites within entity grains mostly disappear. Moreover, despite the deposition strategies exert minimal influence on the tensile properties, the entity fabricated using a 90° continuous deposition strategy achieves an enhanced equilibrium among forming, microstructural, and performance due to its more random heat dissipation. The ultimate tensile strengths and elongations of all entities fall within the range of 518 ∼ 544 MPa and 34.2 %∼47.5 %, respectively, meeting the ASTM A479 standard. These findings greatly expand the potential applications of O-LHAM, facilitating the more efficient and high-quality fabrication of various metal parts, thus accelerating industrialization.

Deposition Stability and Forming Characteristics in Laser-Arc Hybrid Additive Manufacturing of Aluminum Alloy Through Beam Oscillation

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Oscillating Laser-Arc Hybrid Additive Manufacturing of AZ31 Magnesium Alloy

Effect of beam oscillating amplitude on forming quality, microstructure, and mechanical performance of Al-Mg-Sc alloy fabricated by laser-arc hybrid additive manufacturing

Investigation of Arc Stability in Wire Arc Additive Manufacturing of 2319 Aluminum Alloy

Enhanced surface finish and reduced porosity of TiC nanoparticles reinforced 2219 aluminum alloy deposit fabricated via oscillating laser-arc hybrid additive manufacturing

Laser cleaning assisted wire arc additive manufacturing of aluminum alloy thin-wall through synchronous wire-powder deposition

Formation mechanism of Al-Zn-Mg-Cu alloy fabricated by laser-arc hybrid additive manufacturing: Microstructure evaluation and mechanical properties

Wire Oscillating Laser Additive Manufacturing of 2319 Aluminum Alloy: Optimization of Process Parameters, Microstructure, and Mechanical Properties

High-frequency oscillating laser-arc hybrid welding of 8-mm-thick high-strength aluminum alloy through synchronous wire-powder feeding

Microstructure, texture and mechanical properties of Inconel GH4169 superalloy fabricated by wire arc additive manufacturing with arc oscillation

Fabricating exceptionally efficiency and mechanically superior entity through optimized deposition strategy in oscillating laser-arc hybrid additive manufacturing

Multi-Objective Optimization for Forming Quality of Laser and CMT-P Arc Hybrid Additive Manufacturing Aluminum Alloy Using Response Surface Methodology

Effect of Deposition Strategies on Microstructures, Defects and Mechanical Properties of 5356 Aluminum Alloy by Wire Arc Additive Manufacturing

Influence of oscillating laser on forming characteristics and molten pool flow behavior of aluminum alloy double-wire additive manufacturing

High-efficient hybrid arc and friction stir additive manufacturing of high-performance Al-Cu-Mg-Ag-Zr alloy: Microstructural evolution and precipitation behaviors with Ω/L1 2 co-precipitates

Relationship between droplet transfer and forming quality in wire arc additive manufacturing of 2319 aluminum alloy

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Hot-wire Arc Additive Manufacturing of Aluminum Alloy with Reduced Porosity and High Deposition Rate

Tailoring the microstructure and mechanical properties of wire and arc additive manufactured Al-Mg alloy via interlayer friction stir processing

Effect of arc oscillation on porosity and mechanical properties of 2319 aluminum alloy fabricated by CMT-wire arc additive manufacturing