Abstract:Large volume cubic press is one of the most popular high pressure devices which can produce pressures up to about 7 GPa. It is well known experimentally that the enhancing of the maximum pressure generated in the large volume cubic press has attracted wide attention among scientists and engineers because the higher pressure is capable of synthesizing some materials with interesting properties. In the large volume cubic press, pyrophyllite is typically used as a pressure-transmitting medium. A specimen immersed in such a solid experiences a generalized stress state. The pressure distribution in pyrophyllite is an important parameter for characterizing the sample environment and designing the experiments at high pressure. There is a need for the quantitative measurement of pressure gradients in the pyrophyllite pressure medium, so that the accurate experimental data under high pressure can be obtained. In the large volume cubic apparatus (68 MN), we put a circuit into the high pressure cubic cell, so that the pressures at various positions can be measured by using the phase transitions in Bi, Tl and Ba. In the present work, the relationship between the total press load and the press load allocated to the anvil face, and the relationship between the total press load and the press load allocated to gaskets are established at room temperature. The results show that with the increase of the total press load, the load allocated to the gaskets is increased sharply, while the curve of load allocated to the anvil face versus total press load reaches a plateau, which results in the cell pressure reaching upper limit when the cell pressure reaches up to about 5 GPa. According to the experimental results, the stress state of the cubic cell under high pressure is analyzed and the reason why the pressure generated in the large volume cubic chamber is difficult to exceed 7 GPa is explained. Based on the geometrical structure of the cubic cell, the scheme to increase the upper pressure limit for cubic cell by using the material with high bulk modulus as the pressure transmitting medium and the material with low bulk modulus as the gasket, is proposed. Additionally, the method of calculating the pressure values at different positions along the axis of symmetry in the cubic cell is given through the quantitative calibration of the pressure gradient in the axial direction of the cubic cell. This method can provide more accurate pressure data for high pressure experiments.

A Pressure Calibration Method for a Portable Wide-Access “panoramic” Cell

Calibration of Pressure to 35 Gpa for the Cubic Press Using the Diamond-Cemented Carbide Compound Anvil

Force Analysis and Pressure Quantitative Measurement for the High Pressure Cubic Cell

Raman Spectra Based Pressure Calibration of the Non-Gauge Sapphire Anvil Cell at High Temperature and High Pressure

Note: an Anvil-Preformed Gasket System to Extend the Pressure Range for Large Volume Cubic Presses.

Reaserch on Pressure Generation Efficiency of 6-8 Type Multianvil High Pressure Apparatus

Radial Displacement Measurement of Hydrogen Storage Cylinders under Internal Pressure Based on Fringe Projection Profilometry

Quantitative Measurements of Pressure Gradients for the Pyrophyllite and Magnesium Oxide Pressure-Transmitting Mediums to 8 Gpa in A Large-Volume Cubic Cell

Calibration of manganin pressure gauge for diamond-anvil cells

A High P–T Cell Assembly for Neutron Diffraction Up to 10gpa and 1500 K

Deviatoric Stress In A Quasi-Hydrostatic Diamond-Anvil Cell - Effect On The Volume-Based Pressure Calibration

High pressure gas vessels for neutron scattering experiments

In Situ Synchrotron X-ray Diffraction with Laser-Heated Diamond Anvil Cells Study of Pt Up to 95 GPa and 3150 K

Calibration of local chemical pressure by optical probe

Adaptation of the Bridgman anvil cell to liquid pressure mediums

Probing local pressure environment in anvil cells with nitrogen vacancy (NV-) centers in diamond

Application of a New Composite Cubic-Boron Nitride Gasket Assembly for High Pressure Inelastic X-Ray Scattering Studies of Carbon Related Materials.

Bullet pressure-cell design for neutron scattering experiments with horizontal magnetic fields and dilution temperatures

A nano-polycrystalline diamond anvil cell with bulk metallic glass cylinder for single-crystal neutron diffraction

Permanent Densification of Silica Glass for Pressure Calibration Between 9 and 20 GPa at Ambient Temperature

Large volume high pressure research using the wiggler port at NSLS