Abstract:Large volume cubic press is one of the most popular high pressure devices which can produce pressures up to about 7 GPa. It is well known experimentally that the enhancing of the maximum pressure generated in the large volume cubic press has attracted wide attention among scientists and engineers because the higher pressure is capable of synthesizing some materials with interesting properties. In the large volume cubic press, pyrophyllite is typically used as a pressure-transmitting medium. A specimen immersed in such a solid experiences a generalized stress state. The pressure distribution in pyrophyllite is an important parameter for characterizing the sample environment and designing the experiments at high pressure. There is a need for the quantitative measurement of pressure gradients in the pyrophyllite pressure medium, so that the accurate experimental data under high pressure can be obtained. In the large volume cubic apparatus (68 MN), we put a circuit into the high pressure cubic cell, so that the pressures at various positions can be measured by using the phase transitions in Bi, Tl and Ba. In the present work, the relationship between the total press load and the press load allocated to the anvil face, and the relationship between the total press load and the press load allocated to gaskets are established at room temperature. The results show that with the increase of the total press load, the load allocated to the gaskets is increased sharply, while the curve of load allocated to the anvil face versus total press load reaches a plateau, which results in the cell pressure reaching upper limit when the cell pressure reaches up to about 5 GPa. According to the experimental results, the stress state of the cubic cell under high pressure is analyzed and the reason why the pressure generated in the large volume cubic chamber is difficult to exceed 7 GPa is explained. Based on the geometrical structure of the cubic cell, the scheme to increase the upper pressure limit for cubic cell by using the material with high bulk modulus as the pressure transmitting medium and the material with low bulk modulus as the gasket, is proposed. Additionally, the method of calculating the pressure values at different positions along the axis of symmetry in the cubic cell is given through the quantitative calibration of the pressure gradient in the axial direction of the cubic cell. This method can provide more accurate pressure data for high pressure experiments.

Note: an Anvil-Preformed Gasket System to Extend the Pressure Range for Large Volume Cubic Presses.

Calibration of Pressure to 35 Gpa for the Cubic Press Using the Diamond-Cemented Carbide Compound Anvil

Force Analysis and Pressure Quantitative Measurement for the High Pressure Cubic Cell

A Hybrid Pressure Cell of Pyrophyllite and Magnesium Oxide to Extend the Pressure Range for Large Volume Cubic Presses

Two stage 6-8 Type Large Cavity Static High Pressure Device Based on the Domestic Cubic Press

A Large Volume Cubic Press with A Pressure-Generating Capability Up to about 10 Gpa

Reaserch on Pressure Generation Efficiency of 6-8 Type Multianvil High Pressure Apparatus

A Simplified Rapid-Quench Multi-Anvil Technique.

Influence of Mechanical Configuration and Hardness of Last Stage Anvil on High Pressure Producing Efficiency for Octahedral Cell

A Nearly Zero Temperature Gradient Furnace System for High Pressure Multi-Anvil Experiments

Exploring toroidal anvil profiles for larger sample volumes above 4 Mbar

A Pressure Calibration Method for a Portable Wide-Access “panoramic” Cell

High-pressure Preparation of Bulk Tungsten Material with Near-Full Densification and High Fracture Toughness

Operation of Large-Volume Cubic Press above 8 GPa and 2500°C with a Centimeter-Sized Cell Volume Using an Optimized Hybrid Assembly

Raman Spectra Based Pressure Calibration of the Non-Gauge Sapphire Anvil Cell at High Temperature and High Pressure

A Diamond Gasket for the Laser-Heated Diamond Anvil Cell

Large-volume Cubic Press Produces High Temperatures above 4000 Kelvin for Study of the Refractory Materials at Pressures.

Application of a New Composite Cubic-Boron Nitride Gasket Assembly for High Pressure Inelastic X-Ray Scattering Studies of Carbon Related Materials.

In situ synchrotron X-ray diffraction with laser-heated diamond anvil cells study of Pt up to 95 GPa and 3150 K

Fe0.79Si0.07B0.14 metallic glass gaskets for high-pressure research beyond 1 Mbar

Materials for Ultrahigh Pressure Sealing in Bridgman Anvil Devices