Abstract:Large volume cubic press is one of the most popular high pressure devices which can produce pressures up to about 7 GPa. It is well known experimentally that the enhancing of the maximum pressure generated in the large volume cubic press has attracted wide attention among scientists and engineers because the higher pressure is capable of synthesizing some materials with interesting properties. In the large volume cubic press, pyrophyllite is typically used as a pressure-transmitting medium. A specimen immersed in such a solid experiences a generalized stress state. The pressure distribution in pyrophyllite is an important parameter for characterizing the sample environment and designing the experiments at high pressure. There is a need for the quantitative measurement of pressure gradients in the pyrophyllite pressure medium, so that the accurate experimental data under high pressure can be obtained. In the large volume cubic apparatus (68 MN), we put a circuit into the high pressure cubic cell, so that the pressures at various positions can be measured by using the phase transitions in Bi, Tl and Ba. In the present work, the relationship between the total press load and the press load allocated to the anvil face, and the relationship between the total press load and the press load allocated to gaskets are established at room temperature. The results show that with the increase of the total press load, the load allocated to the gaskets is increased sharply, while the curve of load allocated to the anvil face versus total press load reaches a plateau, which results in the cell pressure reaching upper limit when the cell pressure reaches up to about 5 GPa. According to the experimental results, the stress state of the cubic cell under high pressure is analyzed and the reason why the pressure generated in the large volume cubic chamber is difficult to exceed 7 GPa is explained. Based on the geometrical structure of the cubic cell, the scheme to increase the upper pressure limit for cubic cell by using the material with high bulk modulus as the pressure transmitting medium and the material with low bulk modulus as the gasket, is proposed. Additionally, the method of calculating the pressure values at different positions along the axis of symmetry in the cubic cell is given through the quantitative calibration of the pressure gradient in the axial direction of the cubic cell. This method can provide more accurate pressure data for high pressure experiments.

Influence of Mechanical Configuration and Hardness of Last Stage Anvil on High Pressure Producing Efficiency for Octahedral Cell

Reaserch on Pressure Generation Efficiency of 6-8 Type Multianvil High Pressure Apparatus

Calibration of Pressure to 35 Gpa for the Cubic Press Using the Diamond-Cemented Carbide Compound Anvil

Force Analysis and Pressure Quantitative Measurement for the High Pressure Cubic Cell

Two stage 6-8 Type Large Cavity Static High Pressure Device Based on the Domestic Cubic Press

Note: an Anvil-Preformed Gasket System to Extend the Pressure Range for Large Volume Cubic Presses.

Quantitative Measurements of Pressure Gradients for the Pyrophyllite and Magnesium Oxide Pressure-Transmitting Mediums to 8 Gpa in A Large-Volume Cubic Cell

Revealing the Interrelation Between Process Parameters and Microstructure to Promote the Mechanical Performance for Hastelloy-X

Effect of High Temperature-High Pressure Treatment on Microstructure and Mechanical Properties of Cu-Cr Alloy

Effect of High Pressure on Microstructure of Crystallizing Amorphous Nd9Fe85B6 Alloy

Research on Aerodynamic and Strength Performance of Last Stage in High-Pressure Cylinder of Steam Turbine under Variable Working Conditions

Structural transition, mechanical properties and electronic structure of the ZnO under high pressure via first-principles investigations

Microstructural Evolution and Mechanical Properties of Al–Si–Cu–(Ge)–(Mg) Alloy Solidified under High Pressure

A Large Volume Cubic Press with A Pressure-Generating Capability Up to about 10 Gpa

Effect of Mechanical Pressure on Rate Capability, Lifetime, and Expansion in Multilayer Pouch Cells with Silicon-Dominant Anodes

Theoretical analyses of mechanical performance of higher-order vertex-based hierarchical square cell structure subjected to compression

Recent Design of Ultrahigh-Pressure Diamond Cell

Exploring toroidal anvil profiles for larger sample volumes above 4 Mbar

MECHANICAL BEHAVIOR OF Al-20Mg ALLOY SOLIDIFIED UNDER HIGH PRESSURE

Theoretical insights into the crystal and fundamental properties of MgAl9Zn compound: First-Principles calculations

Operation of Large-Volume Cubic Press above 8 GPa and 2500°C with a Centimeter-Sized Cell Volume Using an Optimized Hybrid Assembly