Abstract:In this study, in order to investigate the influence of melt shearing on the phase morphology and mechanical performance of PP/EPDM thermoplastic vulcanizates (TPVs), the oscillatory melt shear was successively applied on the TPV melt in the mold cavity during the packing stage of injection molding by a modified facility, called dynamic-packing injection molding. For a clear comparison, conventional injection molding was also used. It is shown that conventional injection-molding results in large EPDM rubber aggregates with dimensions of ∼1.5 μm dispersed in the PP matrix. To our surprise, well-dispersed nanoscale EPDM particles with dimensions of ∼40 nm have been achieved for the first time when introducing oscillatory melt shearing, in additional to a largely enhanced molecular orientation for PP matrix. As a result, a simultaneous improvement of tensile strength and elongation has been achieved for dynamic packing injection molded samples. In addition, step cycle tests showed typical “Mullins effect” for both conventional injection-molded samples and dynamic packing injection molded samples but improved fatigue resistance for dynamic packing injection molded ones. To isolate the contribution of PP matrix orientation and nanoscale EPDM particle on the tensile behavior of PP/EPDM TPVs, thermal annealing of injection molded samples were carried out to eliminate the orientation of PP matrix. It was found that the tensile strength is decreased but the elongation at break is maintained after annealing of dynamic packing injection molded samples. By comparing the property change before and after annealing, it is concluded that the orientation of PP matrix is in great favor of Young's modulus and tensile strength while the enhanced elongation at break is directly corresponding to the decreased rubber size and improved dispersion in TPVs. Our work demonstrates the strong effect of melt shearing on the breakup of rubber particles and matrix orientation of TPVs as well. The isolation of the contribution of PP matrix orientation and rubber particle size on the tensile behavior of TPVs provides guidance for the preparation of new TPVs with high performance.

Zinc Dimethacrylate Induced in Situ Interfacial Compatibilization Turns EPDM/PP TPVs into a Shape Memory Material

In Situ Reactive Compatibilization and Reinforcement of Peroxide Dynamically Vulcanized Polypropylene/ethylene‐propylene‐diene Monomer Tpv by Zinc Dimethacrylate

Ethylene propylene diene monomer/polypropylene thermoplastic elastomer modified with in situ prepared zinc dimethacrylate

Shape Memory Effect of Dynamically Vulcanized Ethylene-Propylene-diene Rubber/polypropylene Blends Realized by In-Situ Compatibilization of Sodium Methacrylate

Magnesium Acrylate Induced Interfacial Compatibilization of EPDM/PP Thermoplastic Vulcanizate and Shape Memory Behavior

PP/EPDM-based Dynamically Vulcanized Thermoplastic Olefin with Zinc Dimethacrylate: Preparation, Rheology, Morphology, Crystallization and Mechanical Properties

Reactive Compatibilization of Zinc Dimethacrylate on Dynamically Vulcanized Thermoplastic Polyurethane/silicone Rubber Blends

Morphology Study of Peroxide-Induced Dynamically Vulcanized Polypropylene/Ethylene-Propylene-Diene Monomer/Zinc Dimethacrylate Blends During Tensile Deformation

The effect of rubber and plastic mass ratio on the compatibilized ethylene propylene diene monomer/polypropylene TPV with shape memory behavior

Fabrication of EPDM/LDPE shape memory composites: the effect of vulcanization and crystals

In Situ Reactive Compatibilized Polypropylene/Nitrile Butadiene Rubber Blends by Zinc Dimethacrylate: Preparation, Structure, and Properties

Fully Biobased Shape Memory Material Based on Novel Cocontinuous Structure in Poly(Lactic Acid)/Natural Rubber TPVs Fabricated Via Peroxide-Induced Dynamic Vulcanization and in Situ Interfacial Compatibilization

Structure and Properties of Peroxide Dynamically Vulcanized Polypropylene/Ethylene-Propylene-Diene/Zinc Dimethacrylate Composites

HEAT-TRIGGERED SHAPE MEMORY EFFECT OF PEROXIDE CROSS-LINKED ETHYLENE–METHACRYLIC ACID COPOLYMER/NITRILE–BUTADIENE RUBBER THERMOPLASTIC VULCANIZATES WITH SEA-ISLAND STRUCTURE

Preparation and Properties of Peroxide Dynamically Vulcanized Polypropylene/ethylene‐propylene‐diene Monomer/zinc Dimethacrylate Thermoplastic Olefin

A novel polymer based on ethylene-methyl acrylate copolymer/chloroprene rubber thermoplastic vulcanizates with rapid thermo-responsive shape memory property

Preparation and Properties of Peroxide Dynamically Vulcanized Poly(vinylidene Fluoride)/silicone Rubber/zinc Dimethacrylate Composites

Highly Toughened Polypropylene/ethylene–propylene-Diene Monomer/zinc Dimethacrylate Ternary Blends Prepared Via Peroxide-Induced Dynamic Vulcanization

Property enhancement of PP-EPDM thermoplastic vulcanizates via shear-induced break-up of nano-rubber aggregates and molecular orientation of the matrix

Mechanically Robust, Reprocessable Shape Memory Fluorosilicon Materials Using Β-H Elimination Reaction and in Situ Interfacial Compatibilization

Silica‐reinforced Ethylene Propylene Diene Monomer/polypropylene Thermoplastic Vulcanizates with Interfacial Compatibilized by Methylacrylate