Abstract:In order to obtain softer polyolefins applicable as toughener for polypropylene (PP), a series of in-reactor alloys composed of polyethylene, crystalline ethylene-propylene copolymer (cEP) and amorphous ethylene-propylene copolymer (aEP) were synthesized by sequential ethylene polymerization followed by ethylene-propylene copolymerization in periodic switching polymerization process (PSPP) using a spherical MgCl2-supported Ziegler-Natta catalyst. In the PSPP step, ethylene-propylene copolymerization was repeatedly switched between two different monomer feed ratios: one with high propylene/ethylene ratio to form aEP component, and the other with low propylene/ethylene ratio to form cEP component. In the synthesized PE/cEP/aEP in-reactor alloys, aEP accounted for 40∼56 wt.%, and cEP accounted for 18∼30 wt.% of the alloy. With aEP content rising above 48 wt.%, the alloys showed rather low modulus, and no yielding appeared in their stress-strain curve, implying that they were a sort of elastomeric material. By blending the PE/cEP/aEP alloys with isotactic PP, their PP-toughening performances were evaluated and compared with a commercial EPDM. Impact strength of PP toughened by the alloy was significantly higher than that toughened by EPDM at the same blend ratio. Cryo-fractured surface of PP/alloy blends showed that the alloy particles were uniformly dispersed in PP matrix, and showed a core-shell type morphology, in which the core domain was composed of polyethylene, and aEP constituted the shell domain in between the core and the PP matrix. Segmented EP copolymer chains (s-EP) located inside the aEP domains formed thin filaments bridging the core and the PP matrix, which are believed to act as compatibilizer that significantly enhanced interfacial adhesion between the PP matrix and the dispersed phase.

Highly Toughened Polypropylene/ethylene–propylene-Diene Monomer/zinc Dimethacrylate Ternary Blends Prepared Via Peroxide-Induced Dynamic Vulcanization

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Mechanical properties and structural characteristics of dynamically photocrosslinked PP/EPDM blends

Dynamically photocrosslinking of polypropylene/EPDM blends as a thermoplastic elastomer

Mechanical properties, morphological structure, and thermal behavior of dynamically photocrosslinked PP/EPDM blends

Polymer Blends of Pbt and Pp Compatibilized by Epoxidized Ethylene Propylene Diene Rubber

Toughening of Polypropylene Highly Filled with Aluminum Hydroxide

Toughened poly(butylene terephthalate) by epoxided ethylene-propylene-diene-rubber

Toughening with Little Rigidity Loss and Mechanism for Modified Polypropylene by Polymer Particles with Core–shell Structure

Fabrication Of Polypropylene Blends With Excellent Low-Temperature Toughness And Balanced Toughness-Rigidity By A Combination Of Epr And Seeps

Toughening of Poly(ethylene Terephthalate) and Optimizing of the Compatibilization Between PET and EPDM by Functionalized EPDM

Super Toughened Poly(Lactic Acid) Ternary Blends by Simultaneous Dynamic Vulcanization and Interfacial Compatibilization

Combined effects of matrix molecular weight and crystallinity on the impact toughness of PP/EPR blends: The role of chain entanglement

Polyethylene/crystalline ethylene-propylene copolymer/amorphous ethylene-propylene copolymer in-reactor alloys synthesized by periodic switching polymerization process: An excellent toughener for polypropylene

A thermally reversible healing EPDM based elastomer with higher tensile properties and damping properties

Reactive processing of PA6/EPDM‐MA blends as modifier for application and development of high‐performance polypropylene

Balanced toughening and strengthening of ethylene–propylene rubber toughened isotactic polypropylene using a poly(styrene-b-ethylene–propylene) diblock copolymer

Mechanical Properties and Thermal Behaviors of Dynamically Photocrosslinked PP/EPDM Blends

Fabrication and toughening mechanism of high toughness PP/SEBS/HDPE blends with core‐shell particles

Tough and Thermostable Polybutylene Terephthalate (PBT)/Vitrimer Blend with Enhanced Interfacial Compatibility

Toughened Blend of Polycarbonate and Epoxidized Ethylene Propylene Diene Rubber