Influence of Preparation Conditions on the Magnetic Properties of MnZnFe_2O_4 Particles

Zhi Yang

2002-01-01

Abstract:Manganese zinc ferrite(MnZnFe 2O 4)magnetic nano particles were prepared with the coprecipitation method.The magnetic propreties are examined with VSM(vibrating specimen magnetometer).This paper also deals with the influence of reaction temperatures,reaction durations and alkaline quantities on the magnetic properties of the particles.

What problem does this paper attempt to address?

Preparation and Magnetic Properties of Zn–Cu–Cr–Sm Ferrite Via a Rheological Phase Reaction Method

Jing Jiang,Liangchao Li,Feng Xu,Yunlong Xie

DOI: https://doi.org/10.1016/j.mseb.2006.11.014

IF: 3.097

2007-01-01

Journal of Magnetism and Magnetic Materials

Abstract:Nanocrystalline Zn0.6Cu0.4Cr0.5SmxFe1.5−xO4 (x=0.000, 0.025, 0.050, 0.075, 0.100) powders were prepared by a rheological phase reaction method. The obtained powders were characterized by powder X-ray diffractometer (XRD), transmission electron microscope (TEM) and vibrating sample magnetometer (VSM). The results indicated that ferrite samples had the single-phase spinel at low Sm content. Particle sizes calculated from Scherrer's formula decreased with increasing Sm content for the samples, which are consistent with the results obtained by TEM. The magnetic properties of Zn0.6Cu0.4Cr0.5SmxFe1.5−xO4 ferrites were strongly affected by Sm content. The saturation magnetization decreased, while coercivity increased with increasing of Sm content.
Influence of Different Preparation Methods on Crystallisation and Morphology of Fe2o3 Nanoparticles

Ting Wang,Xin Jiang,Huan-cong Huang

DOI: https://doi.org/10.1049/mnl.2010.0045

2010-01-01

Micro & Nano Letters

Abstract:Iron oxide nanoparticles were prepared by adsorption phase synthesis (APS), impregnation method (IM) and precipitation synthesis (PS). The grain sizes of Fe2O3 prepared by APS and IM were much smaller than that by PS. In the APS process, when the reaction took place in the adsorption layer, strong chemical bonds between Fe2O3 particles and silica could be built, which inhibited the phase transformation from gamma-Fe2O3 to alpha-Fe2O3 during the calcination process. The physical interaction did not restrain the crystal transformation although the restriction on the aggregation of Fe2O3 particles was obvious.
Synthesis and Magnetic Properties of Mn-Zn Ferrite Nanoparticles

Yimin Xuan,Qiang Li,Gang Yang

DOI: https://doi.org/10.1016/j.jmmm.2006.11.200

IF: 3.097

2006-01-01

Journal of Magnetism and Magnetic Materials

Abstract:Mn–Zn ferrite nanoparticles (Mn1−xZnxFe2O4) are synthesized by a hydrothermal precipitation approach using metal sulfate solution and aqueous ammonia. The analysis methods of XRPD, TEM, TGA, and VSM are used to characterize the magnetic nanoparticles. Through the characterization of the precipitated nanoparticles, the effects of the reacting component proportions and preparation techniques on the Curie temperature, the magnetization, and the size distribution of Mn–Zn ferrite nanoparticles are discussed. Furthermore, the Mn–Zn ferrite nanoparticles are used to prepare ferrofluid. Variation of the magnetic properties of the ferrite nanoparticles with the composition content x of Zn and the magnetic moment of the nanoparticles are discussed.
Research on the Preparation and Characterization of Magnetic Nanoparticles (mnps) by Chemical Co-precipitation

Guizhong Zhou,Shuo Xu,Wenqian Li,QianYao,Dayi Zhang

DOI: https://doi.org/10.2991/icimm-16.2016.36

2016-01-01

Abstract:The synthesis and characterization of magnetic nanoparticles (MNPs) are attracting more and more attention in recent years. By chemical co-precipitation, NH3 center dot H2O as precipitant, reaction with the mixed solution of Fe2+ and Fe3+, then obtain the nanometer magnetite. The sizesof the products are affected by temperature, stirring speed, the concentration of ferric salt, precipitant concentration, the amount of reactants, and the addition with PAAH which makes its good dispersion. The results showed that the best reaction conditions as follows: reactant ratio is Fe2+:Fe3+:NH3 center dot H2O=1:1:10; precipitant concentration of ammonia is 0.25mol/L; iron concentration (the same solution concentration of Fe2+ and Fe3+) is 0.5mol/L; the temperature control at 25 degrees C; the stirring speed of 1000r/min. The XRD and SEM had carried on the preliminary characterization to MNPs analysis which showed the particle size of MNPs is about 20nm. The magnetic properties of MNPs had also tested by VSM.
Preparation and Properties of Nanosize MnZn Ferrite from Δ-Feooh

Dan Hao,Shunli,Hong Wang,Xin,Hsi-Hsien Wei,Anchi Yu,Yongming,Ming Liu,Chunjing

2006-01-01

Abstract:Ferrous ion was transformed into feroxyhyte (δ-FeOOH) by oxidation. Then, manganese sulfate and zinc sulfate in some ratio were added to the feroxyhyte solution. The co-precipitation was boiling reflux conditions sometime under constant stirring. The nanosize MnZn ferrite powder was formed. The mechanism of preparation of the nanosize MnZn ferrite was discussed, and the formation of feroxyhyte which was playing a key role during the process was mentioned. The properties of powder was tested by means of X-ray diffraction, transmission electron microscopy and vibrating sample magnetometer. The results show that the samples of spherical particles about 20 nm, which have characteristics of ferrimagnetism, has larger saturation magnetization, but the remanent magnetization and coercivity are comparatively smaller. The spinel MnZn ferrite nanosize powder was successfully prepared from δ-FeOOH at low temperature, with low-carbon steel and peroxide as main material.
Effects of Fe2+ Content in Raw Materials on Mn–Zn Ferrite Magnetic Properties

HH Li,ZK Feng,HH He,QQ Zhu,JJ Jiang,JH Nie,XL Yu

DOI: https://doi.org/10.1016/s0304-8853(01)00500-5

IF: 3.097

2001-01-01

Journal of Magnetism and Magnetic Materials

Abstract:The magnetic properties of Mn–Zn ferrite such as initial permeability, saturation magnetization, Curie temperature, resistivity and power loss are affected greatly by the Fe2+ content in the raw materials. The experimental results show that low resistivity (ρ) and high eddy current loss (Pe) are induced by the superfluous Fe2+ content in the raw materials; the scant Fe2+ content in the raw materials will increase hysteresis loss (Ph) and decrease Curie temperature (Tc), saturation magnetization (Ms) and initial permeability (μi).
The Preparation and Haracterization of Nanograined soft Magnetic Mn-Zn Ferrite

Bao-luo WANG,Wei-min FANG

DOI: https://doi.org/10.3969/j.issn.0367-6358.2007.05.002

2007-01-01

Abstract:The Precursor were prepared from FeCl_2,MnSO_4,ZnSO_4 and NiSO_4 by refflecxing in the presence of a small amount of FeSO_4 dried at(140°C),to form soft magnetic Mn-Zn ferrite nano-particle.The properties and structure of the precursor and product were analyzed and characterlized by TG-DTA,XRD,SEM and FT IR.The result showed the present method had advantages of simplicity,high efficiency,short reaction time,mild conditions and low coercivity of product.
Influence of preparation method on structural, optical and magnetic properties of synthesized Zn0.5Mg0.5-xNixFe2O4 nano-ferrite

Abdien Khalafallah,Mohamed Siddig,Obaidallah Algethami,Abdelrahman A. Elbadawi,Abdalskhi S. Mohammed

DOI: https://doi.org/10.1088/2053-1591/ad477d

IF: 2.025

2024-05-04

Materials Research Express

Abstract:Structural, optical, and magnetic properties of ferrite series with chemical formula Zn0.5NixMg0.5-xFe2O4 (x = 0.0, 0.1, 0.2, 0.3 and 0.4) were investigated. Co-precipitation and sol-gel methods were used to synthesis the samples and to investigate further the influence of these preparation methods on the properties of Zn0.5NixMg0.5-xFe2O4 nano-ferrites. X-ray diffraction and Fourier-transform infrared spectroscopy revealed that the samples crystallize in a cubic spinel structure with space group Fd3m:1. The crystallite size of Zn0.5NixMg0.5-xFe2O4 nanoparticles was decreased from 19.15 to 11.65 nm with increasing Ni content for the samples of co-precipitation method, while the opposite behavior was observed in case of sol-gel method which was increased from 13.90 to 21.90 nm. Moreover, the optical investigation by UV-visible spectroscopy revealed that the energy band gap of the samples of co-precipitation method ranged (6.04 - 6.08) eV compared to (4.44 - 4.50) eV of sol-gel method. For both methods, substitution of Ni+2 by Mg+2 in Zn0.5NixMg0.5-xFe2O4 affects the remanent magnetization (Mr), coercivity (Hc) and saturation magnetization (Ms) suggesting the super-paramagnetic behavior of the samples. The substitution of Ni resulted in small values of coercivity ranged 0.758 to 164.62 Oe. The Ms was ranged 20.39 to 127.57 emu/g and an enhancement in magnetization was observed which increases the value of Ms that was found to be maximum with x=0.4 of co-precipitation method (127.57 emu/g). The magnetic behavior of synthesized Ni doped nanoparticles makes them suitable candidate for sensing and high-frequency applications and for use in hyperthermia treatment. The characterization outcomes may recommend that co-precipitation method is preferred over sol-gel method for refined structure and preferable properties of Zn0.5NixMg0.5-xFe2O4 nanoparticles.

materials science, multidisciplinary
Effect of nanoparticles on the magnetic properties of Mn–Zn soft ferrite

Preeti Mathur,Atul Thakur,M. Singh

DOI: https://doi.org/10.1016/j.jmmm.2007.11.008

IF: 3.097

2008-04-01

Journal of Magnetism and Magnetic Materials

Abstract:In this paper, the effect of nanostructures on the magnetic properties like the specific saturation magnetization (σS) and the coercivity (HC) for Mn0.4Zn0.6Fe2O4 ferrite prepared by the co-precipitation method has been presented. We have shown by means of X-ray diffraction that the resulting ferrite is made up of nanoparticles, and that the average size of these nanoparticles calculated with the Scherrer formula depends upon the sintering temperature. When the sintering temperature is increased from 500 to 900°C, the average nanoparticle diameter varies from 19.3 to 36.4nm. The nanoparticle phase is further confirmed by scanning electron microscopy (SEM). Both results are found to be in good agreement. The magnetic properties are explained on the basis of the single-domain and multi-domain theory.

materials science, multidisciplinary,physics, condensed matter
Preparation and Dispersion Technique of Magnetic Fluid Materials

Li Canhua,Pan Feng,Yang Yanbin

DOI: https://doi.org/10.3969/j.issn.1671-3524.2005.04.005

2005-01-01

Abstract:A series of magnetic fluid materials like Zn_0.5 Ni_0.5 Fe_2O_4,ZnFe_2O_4,NiFe_2O_4,BaFe_12O_19 were prepared by the method of acid-corrosion and recombination.In the subsidence experiment,a special investigation was made into dispersion method and technique of these magnetic nano particles in the water phase and of magnetic powder in liquidoid.
High-temperature Solid State Synthesis and Characterization in Magnetic and Transporting Properties of Zn_xFe_(3-x)O_4 Powder

Liqiang Pan

2008-01-01

Abstract:Zn-doped magnetite Fe3O4 samples were prepared at different doped concentrations and annealed at high temperature in ambient air and N2 respectively.X-ray diffraction(XRD)results showed that samples annealed in air were oxidized and the consequent products were partially in α-Fe2O3 form.While for the samples annealed in N2,ZnxFe3-xO4 products of high purity were obtained.The doping of Zn2+ on the tetrahedral sites(A sites)changed the valence distribution of Fe2+ ions on the octahedral sites(B sites).The electron transporting mechanism remained to be variable range hopping(VRH)conduction.Measurement results of magnetic properties indicated that the super exchange coupling interaction between Fe2+ ions was affected by the low doping concentration of Zn2+ ions in the crystal,and the negative magnetoresistivity of ZnxFe3-xO4 was improved as well.
Analysis of Factors Affecting Preparation of Magnetic Fe3O4@PS Nanospheres

Ting Yang,Hai-Lin Cong,You-Qing Shen,Bing Yu

DOI: https://doi.org/10.1080/10584587.2019.1592587

2019-01-01

Integrated Ferroelectrics

Abstract:In this paper, Fe3O4@PS magnetic nanospheres were synthesized by miniemulsion polymerization under different reaction conditions, and their microstructures were observed by transmission electron microscopy. The results show that the shape of magnetic nanospheres changes with temperature and stirring rate. The appearance will also change. We obtained the best morphology when the temperature is 70 degrees C and the stirring rate is 200 rpm. The particle size of Fe3O4@PS nanospheres with superparamagnetism is about 120 similar to 150 nm.
Analysis of the Factors Affecting the Magnetic Characteristics of Nano-Fe3o4 Particles

Cui Hongchao

DOI: https://doi.org/10.1007/s11434-010-4126-z

2011-01-01

Chinese Science Bulletin

Abstract:We prepared Fe3O4 nanoparticles using chemical coprecipitation and studied the factors affecting the magnetic characteristics of nano-Fe3O4 particles. We identified four factors and three levels of an orthogonal experiment and investigated these four factors that affect the magnetic characteristics of the Fe3O4 particles. We obtained important information from this investigation. The Fe3+ to Fe2+ molar ratio, the iron precursor salt, the amount of surfactant and the amount of alkali were found to be important. We also studied the influence of the order of alkali and surfactant addition, the aging time and the stirring speed on the magnetic characteristics of the nano-Fe3O4 particles. The Fe3O4 preparation process was also analyzed.
Selection of Preparation Conditions of Fe3O4 Magnetic Nanoparticles Based on Orthogonal Method

CUI Hongchao,LI Decai

DOI: https://doi.org/10.3969/j.issn.1673-0291.2011.03.002

2011-01-01

Abstract:By chemical co-precipitation method using FeCl3·6H2O,FeCl2·4H2O,ammonia as precipitating agent,conducted a nine group orthogonal experiment to explore the factors of preparation of Fe3O4 Nano-particles: the amount of deionized water();surfactant dosage;ammonia dosage;the ratio of / etc.Do some research on such factors influences on the saturation magnetization and size distribution of Fe3O4.Using vibrating sample magnetometer(VSM) and transmission electron microscopy(TEM) to characterize the particles,and the orthogonal range analysis to identify the optimal process conditions: that A2B1C3D2,deionized water consumption 200ml(Fe3+=0.1mol/L);surfactant dosage is 1ml;ammonia 30ml;/=1.75,when the saturation magnetization of Fe3O4 particles is 62.70 emu/g.
Preparation and Characterization of the Novel Magnetic Nano-Sized Ferrite(Fe_3O_4) Particles Modified by C_(16)H_(33)NaO_2

Ma Xiaohua,Liu Ying,Ren Junzhe,Liu Yongjian

DOI: https://doi.org/10.3969/j.issn.1002-154X.2006.01.003

2006-01-01

Abstract:In order to obtain the ferrite magnetic fluids of higher magneticintensity with a simpler preparation.In this paper,the nano-sizedferrite magnetic particles were prepared by chemical precipitation.The influence of operating temperature(T),time(t),pH(y) and surfactant on the stability of the ferrite magneticparticles(n) were studied.Then studies are made in detail on the formation mechanismof ferrite(Fe_3O_4) particles and the influencing factors.So the most prospect method of preparing Fe_3O_4 of high purity,free particle diameter and even dispersion were found:t=(180 min),T=80℃,y=0.25,n=0.6 The IR measurement indicates that the nano-sized ferrite particles obtained in such a way are packed with surfactants and have an average diameter less than(10 nm).The XRD confirms,ns that the products are ferrite particles.Then the properties are investigated by VSM etc.
Preparation and Surface Modification of Fe<sub>3</sub>O<sub>4 &Lt;/sub>nano-Magnetic Powders

Zhi Li Zhang,Dan Shi,De Cai Li,Qi Han,Ya Fei Shangguan

DOI: https://doi.org/10.4028/www.scientific.net/amr.412.150

2011-01-01

Advanced Materials Research

Abstract:Because of aggregation and low chemical stability of nanomagnetic particles, we use Sol-Gel method as surface modification in this paper to improve the disperse ability and the chemical stability of Fe 3 O 4 particles. At first, Fe 3 O 4 were prepared by chemical-precipitation method. Then, the Sol-Gel method was used to modify the surface of the particles. Core-shell structural Fe 3 O 4 @ S iO 2 composite magnetic particles were prepared by hydrolysis and condensation of tetraethyl orthosilicate using Fe 3 O 4 nanomagnetic particles as seeds. XRD,VSM were applied to characterize the composite magnetic particles. The effects of rotational speed and the quantity of TEOS on the performance of Fe 3 O 4 @ S iO 2 composite magnetic particles were investigated.
Effect of reaction condition on microstructure and properties of (NiCuZn)Fe2O4 nanoparticles synthesized via co-precipitation with ultrasonic irradiation

Yuandong Peng,Chao Xia,Minghui Cui,Zhixin Yao,Xuwu Yi

DOI: https://doi.org/10.1016/j.ultsonch.2020.105369

Abstract:Nano-spinel ferrites synthesized via chemical co-precipitation method are small in size and have serious agglomeration phenomenon, which makes separation difficult in the subsequent process. Ni0.4Cu0.2Zn0.4Fe2O4 ferrites nanoparticles were synthesized via co-precipitation assisted with ultrasonic irradiation produced by ultrasonic cleaner with 20 kHz frequency using chlorinated salts and KOH as initial materials. The effects of ultrasonic power (0, 40 W, 60 W, 80 W) and reaction temperature on the microstructure and magnetic properties of ferrite nanoparticles were investigated. The structure analyses via XRD revealed the successful formation of pure (NiCuZn)Fe2O4 ferrites nanospinel without any impurity. The crystallites sizes were less than 40 nm and the lattice constant was near 8.39 Å. The TEM showed ferrite particle polygonal. M-H analyses performed the saturation magnetization and coercivity of ferrite nanoparticles obtained at the reaction temperature of 25℃ were higher than at 50℃ with same power. The samples exhibited the highest values of Ms 55.67 emu/g at 25℃ and 47.77 emu/g at 50℃ for 60 W and the lowest values of Hc 71.23 Oe at 25℃ for 40 W and 52.85 Oe at 50℃ for 60 W. The squareness ratio (SQR) were found to be lower than 0.5, which revealed the single magnetic domain nature (NiCuZn)Fe2O4 nanoparticles. All the outcomes show the ultrasonic irradiation has positive effects on improving the microstructure and increasing magnetic properties.
Magnetic Structure Evolution in Mechanically Milled Nanostructured ZnFe2O4 Particles

JZ Jiang,P Wynn,S Morup,T Okada,FJ Berry

DOI: https://doi.org/10.1016/s0965-9773(99)00228-7

1999-01-01

Nanostructured Materials

Abstract:Nanostructured partially-inverted ZnFe2O4 particles have been prepared from bulk ZnFe2O4 by high-energy ball milling in an open container. The grain size reduction, cation site distributions, and the evolution of magnetic structures have been studied by x-ray diffraction with Rietveld structure refinements, transmission electron microscopy, and Mössbauer spectroscopy. It is found that a change of magnetic structure from an antiferromagnetic to a ferrimagnetic (or ferromagnetic) structure occurs in the milled samples. This change is correlated with the redistribution of the cations, Zn and Fe, in the A and B sublattices.
The preparation and electromagnetic properties of nickel-zinc ferrite thin films

Yan, Wang,Ying Huang,Qiufen Wang

DOI: https://doi.org/10.4028/www.scientific.net/AMR.287-290.2294

2011-01-01

Abstract:Compared polyvinyl alcohol with citric acid as complexing agent, nanocrystalline nickel-zinc ferrite thin films were prepared by sol-gel method and dip-coating process under different temperature. The phase composition, morphology, magnetic properties and electromagnetic properties of nanocrystalline nickel-zinc ferrite thin films were studied by X-ray diffractometer (XRD), field emission scanning electron microscope (FESEM), vibrating sample magnetometer (VSM) and vector network analyzer. The results show polyvinyl alcohol is the proper complexing agent for the preparation of nanocrystalline nickel-zinc ferrite thin films, which is stacked with sheet crystals and average diameter of about 20nm. The maximum saturation magnetization, the remanence magnetization and the coercivity of prepared nickel-zinc ferrite thin films are 39.38 emu/g, 11.47emu/g and 182.82 Oe, respectively. Through studying the microwave-absorbing properties of thin films, the maximal absorption quantity is determined at 9.2 GHz.
Characteristic of hydrothermal or Sol-Gel synthesized Mn0.8 Zn0.2Fe2O4 magnetic nano-materials

Xiao-jie WANG,Yu SONG,Fei-fei REN,Huang LI,Yong-wei WANG

DOI: https://doi.org/10.3969/j.issn.1674-1404.2009.01.012

2009-01-01

Abstract:The nano-scale Mn0.8Zn0.2Fe2O4 magnetic particles were prepared by hydrothermal and Sol-Gel method.The crystal form and morphology of the samples were characterized by XRD,TEM and ICP.The results showed that both two methods could get spinel structure.The hydrothermal method exhibited a high purity whose average particle size was 11 nm,while the Sol-Gel method was impurity and had a large diameter of 45 nm.The comparison showed that hydrothermal method was an obvious superiority.

Influence of Preparation Conditions on the Magnetic Properties of MnZnFe_2O_4 Particles

Preparation and Magnetic Properties of Zn–Cu–Cr–Sm Ferrite Via a Rheological Phase Reaction Method

Influence of Different Preparation Methods on Crystallisation and Morphology of Fe2o3 Nanoparticles

Synthesis and Magnetic Properties of Mn-Zn Ferrite Nanoparticles

Research on the Preparation and Characterization of Magnetic Nanoparticles (mnps) by Chemical Co-precipitation

Preparation and Properties of Nanosize MnZn Ferrite from Δ-Feooh

Effects of Fe2+ Content in Raw Materials on Mn–Zn Ferrite Magnetic Properties

The Preparation and Haracterization of Nanograined soft Magnetic Mn-Zn Ferrite

Influence of preparation method on structural, optical and magnetic properties of synthesized Zn0.5Mg0.5-xNixFe2O4 nano-ferrite

Effect of nanoparticles on the magnetic properties of Mn–Zn soft ferrite

Preparation and Dispersion Technique of Magnetic Fluid Materials

High-temperature Solid State Synthesis and Characterization in Magnetic and Transporting Properties of Zn_xFe_(3-x)O_4 Powder

Analysis of Factors Affecting Preparation of Magnetic Fe3O4@PS Nanospheres

Analysis of the Factors Affecting the Magnetic Characteristics of Nano-Fe3o4 Particles

Selection of Preparation Conditions of Fe3O4 Magnetic Nanoparticles Based on Orthogonal Method

Preparation and Characterization of the Novel Magnetic Nano-Sized Ferrite(Fe_3O_4) Particles Modified by C_(16)H_(33)NaO_2

Preparation and Surface Modification of Fe&lt;sub&gt;3&lt;/sub&gt;O&lt;sub&gt;4 &Lt;/sub&gt;nano-Magnetic Powders

Effect of reaction condition on microstructure and properties of (NiCuZn)Fe2O4 nanoparticles synthesized via co-precipitation with ultrasonic irradiation

Magnetic Structure Evolution in Mechanically Milled Nanostructured ZnFe2O4 Particles

The preparation and electromagnetic properties of nickel-zinc ferrite thin films

Characteristic of hydrothermal or Sol-Gel synthesized Mn0.8 Zn0.2Fe2O4 magnetic nano-materials

Preparation and Surface Modification of Fe<sub>3</sub>O<sub>4 &Lt;/sub>nano-Magnetic Powders