Abstract:A range of Fe-Cr-Ni alloys are used in nuclear power plants due to their high mechanical strength and corrosion resistance. As a major component of these alloys, Ni contributes to the formation of austenite microstructures. In many nuclear reactor applications the alloys are exposed to ionizing radiation (g-rays) that can continuously decompose water to a range of highly redox active species (such as •OH, H2O2, O2). The change in water chemistry induced by radiation can affect both the general and localized corrosion behaviour of these alloys. In particular, its influence on the susceptibility of an alloy to localized corrosion such as crevice and stress corrosion cracking (SCC) are important for assessment of reactor component aging. As well, corrosion products that dissolve into the reactor coolant can be transported to the reactor core where they can be neutron activated. This can create a radiological hazard for reactor maintenance personnel. Thus, quantifying the rate of general corrosion and the corrosion product transport in a reactor are important safety, operation and maintenance issues. It has been well established that the type of oxide that forms on a surface is a critical factor in determining both general and localized corrosion behaviour. Both alloy composition and water chemistry affect the type of oxide that forms. Systematic studies that examine the effect of alloy composition on corrosion are rare and those available have been conducted mostly from a metallurgical perspective. There are even fewer studies that examine the combined effects of alloy composition and corrosion environment. A fundamental understanding of the mechanism by which the Fe to Ni ratio in a steel alloy influences the corrosion rate in different environments will provide valuable information that can be used for alloy selection and usage. We have investigated the effect of the Fe to Ni ratio of alloy on oxide formation and growth kinetics. For this study, customized steel alloys with different Ni contents and constant Cr content (18 ± 1 %) were prepared. The Ni content ranged from 15 to 25 wt.%, within the range between AISI 316L and Alloy 800 (Fig. 1). The corrosion kinetics was investigated using a combination of coupon corrosion tests and electrochemical measurements. These measurements were augmented by oxide surface and depth analyses using several spectroscopic and imaging techniques, and by post-test solution analyses for dissolved metal loss. We found that the oxide formed at pH 10.6 and 80 °C has a graded layer structure, consisting of a mixed spinel oxide (FeCr2O4/Fe3O4/NiFe2O4) as an inner layer and Ni(OH)2 as an outer layer. The increase in Ni content from 15 to 25 wt.% does not affect the inner layer but increases the thickness of the Ni(OH)2 layer. The increase in Ni content also decreases the total amount of dissolved metal loss. Gamma-irradiation of the corroding system increases the corrosion potential on these alloys. Correspondingly, gamma-radiation accelerates the formation of passive oxide layers and decreases the overall rate of metal dissolution. The observed kinetics of oxide growth and metal dissolution can be explained by the competition kinetics of oxide growth and dissolution for oxidized metals. Figure 1

Effect of Operating Parameters on CorrosionBehavior of NiFe_2O_4 Cermet Inert Anodes

Electrochemical properties of Ml(NiCoMnCu)5 used as an alkaline fuel cell anode

The Effects of Alloying Elements Cr, Al, and Si on Oxidation Behaviors of Ni-Based Superalloys

Long-Term Testing of WC–Ni–Fe Coating as an Inert Anode in a Low-Temperature Electrolyte for Aluminum Production

EIS study of oxidation heat‐treatment effects on corrosion behavior of Ni10Cu11Fe6Al metallic inert anode inside molten calcium chloride salt

Corrosion Behavior of FeCoNiCrAl High-Entropy Alloy in Molten NaNO3-KNO3

Effect of Nickel Content on the Corrosion Behaviour of Stainless Steel at 80 °C

Performance Evaluation of Low-Temperature KF-NaF-AlF₃ Electrolytes for Aluminum Electrolysis Using Vertical Inert Cu-Ni-Fe Alloy Anodes

Effect of Ni content on the corrosion behavior of Mo2NiB2–Ni cermet in H2SO4 solution

Comparison of Corrosion Behavior Between Coarse Grained and Nanocrystalline Ni Fe Alloys in Chloride Solutions and Proton Exchange Membrane Fuel Cell Environment by EIS, XPS and Raman Spectra Techniques

Local Basicity Dependent Gas-Liquid Interfacial Corrosion of Nickel Anode and Its Protection in Molten Li 2 CO 3 -Na 2 CO 3 -K 2 CO 3

Corrosion behaviors of amorphous and nanocrystalline Fe-based alloys in NaCl solution

Corrosion-Engineered Morphology and Crystal Structure Regulation toward Fe-Based Efficient Oxygen Evolution Electrodes

Anodizing of Pure Aluminum Alloy with Incorporated Ferric Oxide Nanoparticles to Enhance the Aluminum Corrosion Resistance

Microstructure and Mechanical Properties of Ni/10 Mol% Sc2O3–1 Mol% CeO2–ZrO2 Cermet Anode for Solid Oxide Fuel Cells

Performance Evaluation and Durability Analysis of NiFeCoOx Catalysts for Alkaline Water Electrolysis in Anion Exchange Membrane Electrolyzers

Effect of cell sintering temperature on the performance of non-noble metal loaded cerium oxide SOEC anodes

The Impact of NiO on Microstructure and Electrical Property of Solid Oxide Fuel Cell Anode

Electrochemical impedance study of corrosion of pure Ni, Fe, Cr, and Fe‐5Cr alloy in molten nitrides

In‐situ Surface‐selective Removal of Al Element from NiFeAl Ternary Nanowires for Large‐current Oxygen Evolution Reaction

Evaluation of corrosion resistance of electrodeposited nanocrystalline Ni–Fe alloy coatings