THE STRUCTURAL VIBRATION ANALYSIS METHOD FOR VEHICLE'S NOISE FACTOR

L I Keqiang,Yusheng He,Liang Xichang,Shu Hong-yu

1996-01-01

Abstract:This paper introduces a structural vibration contribution analysis method for vehicle's interior noise factor testing analysis method. Based on the theoretical description, the method is successfully applied to a truck cab as a coupled acoustic structural system.

What problem does this paper attempt to address?

A Numerical Method for Analyzing the Low-Frequency Noise of Bridge under Vehicle Load

Yong Ding,Xu Xie,Hui Li,Jianyuan Huang

DOI: https://doi.org/10.1061/41039(345)611

2009-01-01

Abstract:A numerical method is developed to analyze the low-frequency noise of bridge under vehicle load. It is divided into two sections: (1) the analysis of vehicle-bridge interaction system based on finite element method (FEM), when the bridge is modeled by shell element and vehicle is modeled by a theoretical model with four degrees of freedom; (2) the numerical method to predict the low-frequency noise caused by bridge vibration, when the sound pressure is derived using the theory of acoustics and Fast Fourier Transform (FFT) technology. As an example, the low-frequency noise of a practical bridge is investigated. The numerical results are compared with the measured data in experiments, which indicate the validity of the current method. Finally, the influence of road surface roughness is discussed.
Investigation of Noise Characteristics of Electric Vibrator Utilizing Acoustic Camera and Transfer Path Analysis

Zhenyu Xu,Zhangwei Chen

DOI: https://doi.org/10.1088/1361-6501/ad6e0f

IF: 2.398

2024-01-01

Measurement Science and Technology

Abstract:Mechanical equipment operation frequently results in noise generation, which can raise concerns regarding quality and safety. This study focuses on electric vibrators, essential electromechanical systems, with the goal of identifying the source and transfer path of noise. To achieve this objective, an acoustic camera positioning analysis was performed to approximate the distribution and characteristics of the noise. Building upon this foundation, a thorough evaluation of the transfer path and noise contribution was conducted. Subsequently, targeted noise suppression methods were implemented based on the properties of the noise. Primary noise sources were observed to be classified into wind turbulence and mechanical vibration based on operating conditions. Time-frequency analysis revealed the presence of low-frequency signals (around 50 Hz) and intermediate-frequency signals (around the resonant frequency), corresponding to wind-induced and mechanical response noise, respectively. Leveraging the characteristics of the noise and its transfer path, passive methods (Sound-absorbing rubber and Soundproof cotton) and active method (filtered-x least mean squares algorithm) were employed. The findings of this study contribute to a better understanding of noise mechanisms and provide insights for noise emission strategies.
Acoustic-Structural Coupled Modal Analysis Method and It S Application in Vehicle Interior Noise Control

李传兵,李克强

DOI: https://doi.org/10.3969/j.issn.1004-4523.2002.03.019

2002-01-01

Abstract:Without consideration of acoustic-structural coupled factors in conventional modal analysis method for the control of vehicle interior noise generated by vibration of vehicle body, this paper presents acoustic-structural coupled modal analysis method to investigate control algorithm of vehicle interior noise. Using this method, both vehicle body structures and interior sound field could be synthetically analyzed. On the basis of the theory on acoustic-structural coupled modal analysis, emphases are put on discussion of realization of acoustic-structural coupled modal analysis method in vehicle interior noise control. The experimental results demonstrate that the method of acoustic-structural coupled modal analysis is feasible and effective in vehicle interior noise control.
Acoustic Modelling and Analysis of Vehicle Interior Noise Based on Numerical Calculation

Binxing Wang,Sifa Zheng,Lin Zhoul,Shengqiang Liu,Xiaomin Lian,Keqiang Li

DOI: https://doi.org/10.1109/icicta.2010.582

2010-01-01

Abstract:In this paper, various numerical calculation methods are rigorously combined to model and analyze the acoustic characteristics of a heavy truck cab. Firstly a brief introduction of different numerical calculation methods is given, then the finite element structure model and cavity model of the cab are built. The statistical energy analysis models of the cab, including structural subsystems and cavity subsystems, are also built and used in the high-frequency range. The panel acoustic contribution analysis and the energy transfer path contribution analysis are carried out to find the panels which contribute most to the sound pressure inside the cab. Based on the analysis results, structure modification of these panels has been proposed with acoustics topology optimized. The optimization result shows that the sound pressure level on the side of the driver’s right ear can be reduced by a few decibels. Necessary tests to validate the models are also administered.
Application of Acoustic Transfer Vector Algorithm on Acoustic Radiation for Drive Axle of Automobile

Ran GONG,Xiao-jun ZHOU,Zhi-gang ZHANG,Fu-chun YANG

DOI: https://doi.org/10.3321/j.issn:1001-7372.2008.01.021

2008-01-01

Abstract:In order to analyze and control radiated noise induced by the powertrain system of automobile, acoustic transfer vector algorithm was applied for the structural acoustic radiation simulation of the powertrain system. Taking drive axles as examples, acoustic responses, such as radiation pressure, the field point sound pressure level of the drive axle were calculated with this algorithm. An experimental investigation was performed in the drive axle test rig by comparison of numerical and experimental results to enable an assessment of the accuracy level. Experimental results indicate that virtual prediction data agree well with test data. It shows that this simulation method based on acoustic transfer vector algorithm has excellent reliability to predict vibro-acoustic performance of the powertrain system to pre-determined design targets, and it is a reliable method which is applied to structural vibro-acoustic analysis in the process of automobile product design.
Theoretical analysis of low-frequency noise radiated from bridge vibrations

Xie Xu,Zhang He,Zhang Zhicheng

DOI: https://doi.org/10.3321/j.issn:1000-131x.2008.10.008

2008-01-01

Abstract:The vehicle-bridge coupling vibration theory and the propagation principle of air wave are applied to establish a numerical method for calculation of low-frequency noise induced by bridge vibrations.A simply supported steel bridge in service is simulated as a lattice girder model as a case study.Dynamic responses of the bridge due to vehicles are calculated and the sound pressures of low-frequency noises are obtained by using the numerical method,and the results are compared with the experimental data to validate the probability of the theoretical approach to sound pressure computation.Further studies on the effects of parameters such as road surface roughness and parameters of vehicles have been conducted.According to the analysis,smoothing road surface may decrease low-frequency noise produced by bridge vibration,the simulation method for vehicles has certain effects on the calculation of sound pressures,and in order to increase the calculation accuracy,the calculation for bridge vibration in high frequency range,the non-stationary signal analysis,the boundary absorption and reflection of sound wave need further improvements.
Numerical Analysis and Structure Improvement of Automotive Exhaust Muffler's Acoustic Characteristics

GONG Jian-guo,JIN Tao,MA Yu-shan,CUI Wei-sheng

DOI: https://doi.org/10.3969/j.issn.1006-1355-2011.02.015

2011-01-01

Abstract:Exhaust muffler's sound field is calculated with Sysnoise software.Sound pressure distribution and transmission loss plot are obtained.Noise elimination structure is improved,and a diaphragm and two perforated pipes are set inside the muffler.The results show that the acoustic wave with low frequency propagates in a form of plane wave,while acoustic wave with high frequency propagates in a form of high-order harmonic wave.Compared with the original muffler,the improved muffler's transmission loss increases by more than 20 dB in 600-1200 Hz,1700-1800 Hz and 2700-2800 Hz frequency ranges.And the improved muffler's transmission loss increases by 19.8 dB in average in 20-3000 Hz frequency range.Thus,the improved muffler's noise elimination effect is good.
Finite Element Method Simulation Analysis for Sound Field of Exhaust Muffler

Ge Xiulong,Yu Zitao

DOI: https://doi.org/10.3969/j.issn.1673-6397.2006.02.001

2006-01-01

Abstract:In this paper,exhaust noise of S195 diesel engine was analyzed in details on the bases of theoretical and experiment datum.In the experiment,we measured the frequency of the exhaust noise,and studied the muffler influence with the different rate of expansion.In addition,the paper presented the influence of different shutter positions to the simple expansion cavity muffler.By the finite element method,the paper analyzed the sound field of the muffler,and compared it with experimental results.Because of simplified model,there are some differences between the analysis result and experimental data,but the trends are coincident.
Response Analysis of Interior Structure Noise in Lower Frequency Based on Structure-acoustic Coupling Model

MA Tianfei,GAO Gang,WANG Dengfeng,PAN Feng

DOI: https://doi.org/10.3901/jme.2011.15.076

2011-01-01

Journal of Mechanical Engineering

Abstract:Based on the principle of bearing similar modes with vehicle,the simplified FE model of a heavy commercial vehicle cab is built.A structure-acoustic coupling model of the cab is built with the FE model,and it is validated with an acoustic modal test.The excitation signals at cab mounting and the respond signals of interior noise and vibration are measured under idling condition and even-speed driving condition with road testing.Appling the excitation signals to the structure-acoustic coupling model,the frequency response analysis is carried out and the interior structure noise between 20 Hz and 200 Hz is calculated.The simulated response of vibration and noise is compared with the result of testing.It is shown that the frequency spectrum of simulated response can express the effect of excitation spectrum and acoustic modes,and it coincides with the testing result.It can reach high accuracy to predict the level of interior noise and vibration with the structure-acoustic coupling model.To predict the level of interior noise and vibration by using this model can reach high precision.
Acoustic Topology Optimization of a Truck Cab Based on Coupled Panel Contribution Analysis

Wang Binxing,Zheng Sifa,Hao Peng,Lian Xiaomin,Li Keqiang

DOI: https://doi.org/10.1109/icece.2010.88

2010-01-01

Abstract:Computer simulation technology is of increasing importance in the vibro-acoustic analysis and design of complex mechanical systems, such as vehicles, ships, aircraft, etc.. In this paper, an acoustic topology optimization method based on coupled panel contribution analysis of cab is proposed. The finite element structure model and cavity model of a real heavy duty truck cab are built. The structural modes, cavity modes and the structural--acoustic coupling modes are analyzed. Then the panel acoustic contribution analysis is carried out to find the panels which contribute most to the sound pressure inside the cab. Finally, the panel's shape modification is proposed with acoustics topology optimized. The result shows the sound pressure level on the side of the driver's right ear can be reduced by 5 dB at most. Necessary tests are also administered to validate the models.
Low-noise structure optimization of a heavy commercial vehicle cab based on approximation model

Zhiyong Zhang,Yibo Zhang,Caixia Huang,Xin Liu

DOI: https://doi.org/10.1177/1461348418798403

2018-09-08

Abstract:Structure design for reducing noise is essential and widely studied because cab interior noise seriously affects the ride comfort of the driver and passengers, especially for heavy commercial vehicles. This paper proposes an enhancement investigation on the low-noise structure performance of a cab in a heavy commercial vehicle based on an approximation model. A series of vibroacoustic tests with varying running speeds are implemented first to acquire the vibration signals at four cab suspensions and the sound pressure signal at the right ear of the driver. The finite element model and structure–acoustic coupled model of the cab of a heavy commercial vehicle are established sequentially. When the vibration accelerations measured in the tests are converted into excitation signals using the cab structure–acoustic coupled model, the sound pressure of the right ear of the driver is predicted, and the accuracy of the cab structure–acoustic coupled model is then verified. After panel acoustic contribution analysis, an approximation model of critical panel thickness and the peak noise near the right ear of the driver is established in accordance with the radial basis function. Genetic algorithm is utilized to solve an optimization model to obtain optimal panel thicknesses. By comparing the right ear sound pressure before and after optimization, the results confirm that optimized panel thicknesses can reduce sound pressure level of the critical frequency.

acoustics
Interior Noise Analysis of a Non-load Type Body SUV

Ling LI,Shuai TIAN,Fei KANG,Dong ZHANG,Wen-bin WANG

DOI: https://doi.org/10.3969/j.issn.1006-1335.2015.04.019

2015-01-01

Abstract:The interior low frequency booming noise of vehicles can seriously deteriorate ride comfort. In this paper, the booming noise of a non-load type body SUV at 1700 r/min engine rotation rate in acceleration condition was studied. Through the order analysis, torsional vibration analysis of the powertrain, transfer function analysis and cavity modes analysis, it was found that the interior booming noise is caused by the torque fluctuation of order 2 from the engine. The torsional fluctuation is transmitted through the rear axle to the inside of the vehicle and amplified. Then, it is coupled with the cavity modes so that the loud booming noise occurs. By installing an additive torsional vibration damper, the torsional vibration was efficiently reduced. The test result shows that the vehicle interior booming noise is reduced by 7.5 dB(A), which is acceptable for subjective evaluation. This work provides a reference for seeking and solving the low-frequency booming noise problems.
A Research on the Noise Source Identification and Noise Control of Heavy-duty Truck

Li Linling,Zheng Sifa,Hao Peng,Lian Xiaomin,Li Keqiang

DOI: https://doi.org/10.3321/j.issn:1000-680X.2007.05.005

2007-01-01

Abstract:Taking the respective advantage of sound intensity and sound holography methods,the sources of exterior noise of a heavy-duty truck are comprehensively identified,with the main noise sources and noise frequency ranges obtained.Then various noise control schemes are analyzed,among which the use of optimized sound absorption and insulation structure can reduce the noise by more than 2.5 dB(A)with the adverse effects on the performances of the engine and other systems of the truck within the permitted range and the cost of noise control less than 0.4% of the total cost of the truck.
The testing and improving of the heavy truck vibration

Yuanyuan Zhang,S. M. Li,JianYa Liu,Mujin An,Xiaowei Liu,Jianghui Xin

DOI: https://doi.org/10.1109/CMCE.2010.5609870

2010-01-01

Abstract:For the problem that the truck' cab has an excessive vibration in usual speeds, the vibration testing platform was built, and its vibration characteristics were studied. Though effective testing the signal from the cab and some mount positions in usual different speeds, the signals' frequency components and vibration systems' transmission characteristics were analyzed, and the their correlations were studied, the modal characteristics of cab and frame system were calculated and tested, the results that the most main excitation source is the wheel, and transmission characteristics of the spring and frame system are worse are Acquired. Some proposals reducing the excitation power by doing the dynamic balance to tires, deceasing the stiffness of springs and increasing the stiffness of frame system are carried out on the real truck, and in the usual speeds the road experiments' effects of objective and subjective are great, the achievements are met of factory, which also proves the ideas of studying and solving the truck vibration are effective and could be valuable reference for the same engineering problems. © 2010 IEEE.
Sensor configuration method for identifying vehicle interior noise sources

Sifa Zheng,Peng Hao,Chun Lu,Xiaomin Lian,Keqiang Li

2009-01-01

Abstract:Interior noise is an important index for vehicle's ride comfort. There exist so many noise sources and vibration noises on vehicles simultaneously, it's important to identify the sources and their contribution. Transfer characteristic analysis method was used to identify these sources, including the location and quantity of the sources. In this method, generally the sensors should be placed on each of the possible noise source or vibration source location. How to configure the sensor net was studied in the work. Principle component analysis and correlation analysis were used to identify and separate each of the sources. An optimal sensor configuration was proposed. Finally, the noises sources of a heavy duty vehicle were identified. The experiment result show that the proposed sensor configuration method could be used to identify the vehicle noise sources accurately, and the number of the sensors could be reduced, it's easy to place these sensors in the complex vehicle structure.
Identification of Vehicle’s Interior Noise Source with Operational Transfer Path Analysis

LI Chuan-bing,WANG Bin-xing,LI Hong-cheng,WANG Yue-lin,ZHENG Si-fa

DOI: https://doi.org/10.3969/j.issn.1006-1335.2013.02.018

2013-01-01

Abstract:Transfer path analysis is an important tool to analyze vehicle’s interior noise.Operational transfer path analysis is an improvement of the traditional transfer analysis method.At first,the model for operational transfer path analysis of vehicle’s interior noise was built and the algorithm of matrix transfer method was discussed.Then,the method was applied to a passenger car to analyze the operational transfer path of the interior noise.Finally,contribution of each noise source was analyzed.This work provides a significant support for vehicle’s interior noise control.
Application of measurement technology of sound intensity in noise source identification of automotive interior noise

Shuiming Wan,Lingbin Kong,HaiLin Wang,Fangwu Ma,Qiang Liu,FuQuan Zhao

DOI: https://doi.org/10.1109/MACE.2011.5988714

2011-01-01

Abstract:An application of measurement method of sound intensity is discussed from practical engineering perspective based on experimental analysis to identify the main noise source of vehicle. The 3D sound intensity charts are plotted to find the main noise source which adversely affects interior noise of a specific vehicle at idle condition. Meanwhile, the relevant components are optimized and improved in combination with frequency spectrum analysis to reduce interior noise and improve vehicle NVH performance. The test results indicate that the technology of source intensity measurement and frequency spectrum analysis can be applied to identify the main noise source quickly, and the improvement method is presented accordingly.
Research on optimization control of vehicle road noise performance

Jintao Su,Jianping Lou,Xiaolu Jiang

DOI: https://doi.org/10.1088/1755-1315/769/4/042055

2021-05-01

IOP Conference Series: Earth and Environmental Science

Abstract:Abstract By analyzing the road noise problem of a car model, it is confirmed that the car exists in the car when driving at uniform speed on rough road surface. The front and rear row road noise problem. Based on the existing vehicle CAE model, the TPA analysis of the vehicle model was carried out by using MSC NASTRAN software to obtain the contribution of each transfer path to road noise, and the main path influencing the road noise was locked. The key factors on the main path are further identified through acceleration response analysis of key positions in the transfer path. Through vehicle test and ODS simulation analysis, the main vibration modes of the components that affect the road noise are determined. Combined with CAE and test methods, a reasonable chassis optimization scheme was developed to improve the road noise performance of the vehicle.
Acoustic optimisation design for suspension characteristics based on the method of dynamic subsystem modification

Weiping Ding,Hongliang Li,Yanmei Liu,Mingliang Yang

DOI: https://doi.org/10.1504/IJVNV.2008.021896

2008-01-01

International Journal of Vehicle Noise and Vibration

Abstract:Based on the finite element technique on the structure-acoustic coupling analysis, a dynamic subsystem modification method for the acoustic-vibration characteristic of an elastic thin-walled cavity is introduced in this paper. It is directly applied to the dynamic modification of an automobile's passenger compartment and then supports the Noise, Vibration and Harshness (NVH) performance analysis on the suspension system. The design objective is minimising the sound pressure level of the interior noise of the passenger compartment and the design variables are the stiffness and the damping of suspension system. Finally, the effect of the optimisation design is validated through a calculating example.
Research on Interior Noise Control of the Rear Seats in Vehicle

王永,张永利

DOI: https://doi.org/10.3969/j.issn.1009-9492.2008.04.013

2008-01-01

Abstract:In order to reduce the noise of the rear seats,subjective evaluation and pilot testing and analysis are taken to identify the noise source.The result shows that the noise source of rear seats results from the radiating noise of rear wheel chamber vibration.So a series of measures such as the hang optimization,the structural optimization of wheel chamber and isolating the spreading approach of the noise source are taken to reduce noise,and the marked effect is gained.

THE STRUCTURAL VIBRATION ANALYSIS METHOD FOR VEHICLE'S NOISE FACTOR

A Numerical Method for Analyzing the Low-Frequency Noise of Bridge under Vehicle Load

Investigation of Noise Characteristics of Electric Vibrator Utilizing Acoustic Camera and Transfer Path Analysis

Acoustic-Structural Coupled Modal Analysis Method and It S Application in Vehicle Interior Noise Control

Acoustic Modelling and Analysis of Vehicle Interior Noise Based on Numerical Calculation

Application of Acoustic Transfer Vector Algorithm on Acoustic Radiation for Drive Axle of Automobile

Theoretical analysis of low-frequency noise radiated from bridge vibrations

Numerical Analysis and Structure Improvement of Automotive Exhaust Muffler's Acoustic Characteristics

Finite Element Method Simulation Analysis for Sound Field of Exhaust Muffler

Response Analysis of Interior Structure Noise in Lower Frequency Based on Structure-acoustic Coupling Model

Acoustic Topology Optimization of a Truck Cab Based on Coupled Panel Contribution Analysis

Low-noise structure optimization of a heavy commercial vehicle cab based on approximation model

Interior Noise Analysis of a Non-load Type Body SUV

A Research on the Noise Source Identification and Noise Control of Heavy-duty Truck

The testing and improving of the heavy truck vibration

Sensor configuration method for identifying vehicle interior noise sources

Identification of Vehicle’s Interior Noise Source with Operational Transfer Path Analysis

Application of measurement technology of sound intensity in noise source identification of automotive interior noise

Research on optimization control of vehicle road noise performance

Acoustic optimisation design for suspension characteristics based on the method of dynamic subsystem modification

Research on Interior Noise Control of the Rear Seats in Vehicle