CPLD Realization of RS Encoder

Liu Qin

2002-01-01

Abstract:In this paper,we present a simple CPLD realization of RS encoder on the basis of the theory of RS.After the encoding process is introduced the results are given.

What problem does this paper attempt to address?

Photoelectrical Encoder System Based on CPLD

闫莎莎,朱世强,刘华山,吴剑波

DOI: https://doi.org/10.3969/j.issn.1001-4551.2009.01.023

2009-01-01

Abstract:To improve the feedback precision of the photoelectric encoder and remove the disturbance of the rectangular waveform,a photoelectric encoder measuring system based on complex programmable logic device(CPLD) was offered,which had the ability of frequency multiplication and filtering.The photoelectric encoder measurement principle was introduced.The system was divided into three modules,including filtering phase,frequency and the counter.These three modules were designed and simulated.The simulation results show that the design methods meet signal processing requirements of high-precision servo motor orthogonal coding.
Design and analysis of decoder based on QuartusII softerware

Jun CHEN

DOI: https://doi.org/10.3969/j.issn.1000-0682.2015.02.016

2015-01-01

Abstract:This paper describes the models and principles of decoder,designs implication of 74LS138-decoder and gate device combinatorial logic function and analyses simulation using QuartusII software. It shows the rationality of the design.
Design and Implementation of RS Decoder for CMMB System

CAO Xixin,LIU Jing,ZHANG Qihui,AI Zhuxuan,LIU Peng

DOI: https://doi.org/10.3969/j.issn.1003-4978.2013.01.004

2013-01-01

Abstract:Based on the syndrome computation,modified Euclidean algorithm,Chien's-searching and Forney algorithm,a novel RS decoder for CMMB system is proposed and realized.The RS decoding algorithm is simulated with MATLAB,and then the decoder is functionally verified and synthesized with tools of VCS,Design Compiler and ISE,respectively.The results show that the gate count of our design is as small as the best structure.Our proposed RS decoder has been tested and applied in a CMMB system.
Implement of Multiple Pulse Position Modulation with CPLD

谭家杰,邹常青

DOI: https://doi.org/10.3969/j.issn.1673-0313.2012.03.012

2012-01-01

Abstract:Multiple pulse position modulation （MPPM） is one of the most popular modulations for indoor visible light communi- cation using LED, which has the advantages of high power efficiency, low bandwidth and strong resistance to interference. In order to implement the indoor visible light communication using LED by MPPM, first, the principle of the MPPM and the mapping methods have been analyzed. On this basis, the MPPM modulation and demodulation have been completed by using the CPLD （complex programmable logic device）device, which code word is composed of the synchronous signal and the MPPM signal, and the demodulator uses a digital phase locked loop to extract the bit synchronous signal with CPLD. Finally, we com- plete the MPPM modulation and the demodulation experiments, which show that the MPPM decoding meets the communication requirements, and the results are reliable.
The Design And Implement Of A Receiver For Fsk Signal

Liu Xiao-Peng,Han Yan,Zhong Dong-Dong,Wang Ming-Yu

DOI: https://doi.org/10.4028/www.scientific.net/AMM.190-191.739

2012-01-01

Abstract:A novel frequency shift keying (FSK) receiver is presented, including receiving antennas, a low noise amplifier (LNA), band-pass filters (BPF) and a novel all-digital 2-level FSK demodulator. The Mat lab simulation results of the all-digital FSK demodulator show that it can improve bit error ratio (BER) performance compared with pseudo-coherent FSK demodulation (PCFSK). The novel FSK demodulator defined using Verilog HDL is easy to be implemented on Field Programmable Gate Array (FPGA) and in CMOS integrated circuit. The whole FSK receiver designed and implemented on a PCB board can receive FSK signal and send the recovered data to computer through RS-232 interface.
Design of RS code+DQPSK system based on IP core's Integration

Wang Liang,Ling Kang,Zhang Hailiang,Zhao Xingbo,Zhou Zucheng

DOI: https://doi.org/10.3969/j.issn.1008-0570.2007.17.002

2007-01-01

Abstract:In this paper, we use Altera corporation's RS、NCO、FIR IP core and some modules in the Simulink、DSP_Builder, fast build a low intermediate frequency RS (204,188) +DQPSK modulation/demodulation system, validating the system's function in Simulink and Modelsim environment , finally implementing the system in Stratix II DSP development board and testing the system . Simulation results show that RS (204, 188) coding gain of this scheme can achieve 3￣4dB at bit error rates around 1e- 3 compared with the uncoded DQPSK.
Study on Reconfigurable RS Codec Circuit

TAN Siwei,PAN Hongbing,LONG Hongbo

DOI: https://doi.org/10.3969/j.issn.1671-637x.2010.11.021

2010-01-01

Electronics Optics & Control

Abstract:The existed RS codec is poor in commonality,thus we proposed a new codec circuit structure for multi-standard based on reconfigurable theory.The circuit structure could be reconfigured by inputting configuration information.The encoding theory based on Linear Feedback Shift Register(LFSR) was described and its realization was improved for reconfiguration.The parallel computation of syndrome was achieved by the iteration of multiplication and addition.The key equation was solved by using modified Euclidean algorithm,and the errors were located by Chien's search theory.The reconfigurable computation structures of two algorithms above were also presented.Analysis showed that it was obvious that the new scheme has good versatility which can satisfy the multi-standard of RS code by increasing only a little cost in resource.
RS Decoder Using Software/Hardware Co-design

徐元欣,夏芳,仇佩亮,姚庆栋

DOI: https://doi.org/10.3969/j.issn.1007-0249.2002.03.009

2002-01-01

Abstract:RS code is often used in digital communication system. The theory of RS decoder process is analyzed in this paper. An approach to software/hardware co-design of RS decoder is proposed, and the performance is also analyzed.
High throughput multi-code LDPC encoder for CCSDS standard

Jinfou Xie,Shixian Li,Yun Chen,Qichen Zhang,Xiaoyang Zeng

DOI: https://doi.org/10.1109/ASICON47005.2019.8983513

2019-01-01

Abstract:A high throughput encoder based on Recursive Convolutional Encoder (RCE) circuits is designed for multi-code Quasi-Cyclic Low-Density Parity-Check (QC-LDPC) codes of CCSDS standard. The use of system registers is reduced by employing a parallel RCE circuit structure; by configuring these parallel RCE circuit structures, the encoder can support multiple patterns and code rates. The FPGA implementation results show that the design method can be implemented based on the Xilinx VC690T chip, and its normalized registers and LUTs are reduced by 39.4% and 24.4%, respectively, compared with the existing solutions.
A Modified Systolic Array Reed-Solomon Encoder

曾晓洋,章倩苓,郝志航,魏仲慧

DOI: https://doi.org/10.3321/j.issn:1000-436x.2002.07.011

2002-01-01

Abstract:Firstly, algorithm and structure for RS encoder suiting high application situation were discussed. The encoder consists of r+1 systolic cells, where r is the checking bit numbers. The algorithm of encoder was based on Cauchy representation of generator matrix of the code. There is no global clock in the encoder to pose restrictions on the achievable switching speed of the encoder and so it is suitable for the high-speed applications. Secondly, a modified scheme for the systolic RS encoder was presented: the scheme erases the dividers in the Cauchy cells and the inversion, reduces the complexity of the encoder. So it can boost the throughout of the encoder effectively and is suitable for the very high-speed applications.
FPGA Implementation of Full Parallel LDPC Encoder

Zhaohui Wang,Xin Hao,Yujiao Zhao

DOI: https://doi.org/10.1117/12.2307062

2018-01-01

Abstract:This paper gives a detailed introduction to the FPGA implementation of Full Parallel Low-Density Parity-Check(LDPC) Encoder, which is designed base on Richardson-Urbanke Algorithm with a code length 4096, code rate 4/5 on CCSDS standard. The proposed design use LUTs to solve matrix multiplication with low-complexity, the encode result can output in 4 clocks, the speed of the encoder can be higher than 6.4 Gbps, and the resource utilization is acceptable.
Novel shortened-and-punctured reed-solomon decoder

Hui YU,Zhao-yang ZHANG,Fang FANG

DOI: https://doi.org/10.3785/j.issn.1008-973X.2007.03.010

2007-01-01

Abstract:To resolve the incapability of decoding Reed-Solomon (RS) codes of conventional RS decoders in IEEE802.16d system, optimized design architecture for rate-variable shortened-and-punctured RS decoder was presented. A symmetric generator polynomial was applied, and the number of Galois-field (GF) multiplications was reduced in the encoder. In the decoder, the key function was solved by altering the initial condition of the modified Euclid algorithm (MEA), and a novel shortened-and-punctured RS decoder architecture was proposed based on conventional punctured RS decoder. The design architecture was implemented and verified in field programmable gate arrays (FGPA) chips, and the maximum decoding throughput of six types of RS codes in IEEE802.16d system was analyzed at a particular working clock respectively. The results show that the proposed decoder architecture can achieve a decoding throughput of at least 30 Mbps, and satisfy the requirement of IEEE802.16d system.
The Principle of Reed-Solomon Encoding-Decoding and Its FPGA Implement

ZHOU Zhuan,WANG Rui

DOI: https://doi.org/10.3969/j.issn.1006-141X.2009.02.002

2009-01-01

Abstract:This article briefly describes the principle of Reed-Solomon encoding and decoding and related algorithms, and demonstrates how a RS decoding module is implemented on the basis of Verilog language by using enhanced Berlekamp-Massey algorithm,Chien searching algorithm and Forney algorithms.
RS encoding and decoding architecture based on hardware reusability

pan hongbing,xi zemin,tan siwei

DOI: https://doi.org/10.7495/j.issn.1009-3486.2014.05.019

2014-01-01

Abstract:Based on the principle of FPGA reconfiguration,an architecture of hardware reusability is proposed for RS encoding and decoding,with the aim of solving the problem of high consumption of hardware resources by the traditional RS codec architecture.The logic circuit of the reconfigurable computing module in the codec can be changed according to the configuration information to meet the needs of different algorithms during the encoding and decoding process.The RS codec is acquired by VHDL and tested by Quartus II.The results indicate that the codec can satisfy a variety of errorcorrecting capabilities in RS decoding and encoding,improve the usability of hardware resources by the hardware reusable technique.
Design of RS Decoder Based on DVB-C

GAO Song,PENG Daqin,LIU Huaping

DOI: https://doi.org/10.3969/j.issn.1002-8692.2011.05.004

2011-01-01

Abstract:A RS decoder for the DVB-C system based on the Matlab simulation of the channel outer coder of DVB-C system is designed.The implementation structure of RS decoder is introduced.Based on the modified Euclidean algorithm,the design is implemented with three pipelined to increase throughput,its feasibility and reliability are verified in the FPGA.
Parametric Design of RS Decoding Module in HDTV

张力,徐元欣,王匡,张明

DOI: https://doi.org/10.3969/j.issn.1002-8692.2004.03.017

2004-01-01

Abstract:In this paper, a generally applicable design of RS decoding module is put forward, synthesizing Reed-Solomon codes in different HDTV standards, and the design result is satisfactory.
The Implementation of High- Speed Coding and Decoding of RS Codes Based on DSP

Xue Lifang,Wang Yongliang,Zhang Rong

DOI: https://doi.org/10.3969/j.issn.1008-0570.2007.17.001

2007-01-01

Abstract:In the inertial platform system, some data are transmitted by optical fiber under the control of the optical fiber transmission module. Some key data like platform control parameters have a direct impact on the state of the platform. So the accuracy of the control parameters must be guaranteed by error- correcting to ensure the security of the platform system. The fundamental and coding - decoding algorithm of RS codes are presented, and fast implementation of RS(15,11) codes based on DSP are designed.
Design of Data Acquisition of AHRS Based CPLD

邵科,李平,韩波

DOI: https://doi.org/10.3969/j.issn.1001-182X.2008.10.024

2008-01-01

Abstract:This paper presents a data acquisition method of AHRS of mini autonomous helicopter and designs an attitude data acquisition system with the core of CPLD.The data acquisition system,consisting of CPLD and ADC,realizes data acquisition by SPI module and ADC control module and completes data exchanges with attitude computer through data FIFO and communication module.
Design of a Dynamically Reconfigurable Architecture for Reed-Solomon Decoder

Tan Siwei,Pan Hongbing

DOI: https://doi.org/10.16526/j.cnki.11-4762/tp.2011.03.035

2011-01-01

Abstract:In order to solve the problem of complex architecture and large resource consuming in RS decoder,a dynamically reconfigurable RS decoder is presented.In the decoder,the syndrome calculation and Chien's search algorithm can be realized in the reconfigurable syndrome and Chien's module(RSCM) by reconfiguring the circuit architecture dynamically at discrete time.A decode control module based on state machine is given and is in charge of controlling the function modules in RS decoder.The design is realized by VHDL language in Quartus II 7.2.As it is shown in the result,the encoder could reduce the consuming in hardware resource,and the maximum frequency of this chip could reach at 124MHz.
Research of Encoder in Digital Channelized Receiver

WANG Xin,ZHAO Chun-hui,RONG Jian-gang

DOI: https://doi.org/10.3969/j.issn.1673-9728.2006.03.065

2006-01-01

Abstract:Firstly the importance and necessity of encoder's design in digital channelized receiver and the difficulty degree of this work is pointed out in this paper,the digital channelized method in frequency domain is introduced briefly,secondly one method of encoder's design on basis of instantaneous frequency measurement(IFM) and CORDIC is discussed in detail,at the same time the transient effect of filter is explained,finally the system is simulated in Matlab environment,and better results are received.

CPLD Realization of RS Encoder

Photoelectrical Encoder System Based on CPLD

Design and analysis of decoder based on QuartusII softerware

Design and Implementation of RS Decoder for CMMB System

Implement of Multiple Pulse Position Modulation with CPLD

The Design And Implement Of A Receiver For Fsk Signal

Design of RS code+DQPSK system based on IP core's Integration

Study on Reconfigurable RS Codec Circuit

RS Decoder Using Software/Hardware Co-design

High throughput multi-code LDPC encoder for CCSDS standard

A Modified Systolic Array Reed-Solomon Encoder

FPGA Implementation of Full Parallel LDPC Encoder

Novel shortened-and-punctured reed-solomon decoder

The Principle of Reed-Solomon Encoding-Decoding and Its FPGA Implement

RS encoding and decoding architecture based on hardware reusability

Design of RS Decoder Based on DVB-C

Parametric Design of RS Decoding Module in HDTV

The Implementation of High- Speed Coding and Decoding of RS Codes Based on DSP

Design of Data Acquisition of AHRS Based CPLD

Design of a Dynamically Reconfigurable Architecture for Reed-Solomon Decoder

Research of Encoder in Digital Channelized Receiver