A New Measurement System for Thermophysical Properties

Shaozhi Deng

2001-01-01

Abstract:A new measurement system and method which could be used to measure thermophysical properties for metallic material at phase transfer point dynamically and precisely has been studied in this paper. By using the device and the method, the thermophysical properties of some high melting point metals and alloys have been decided, which were unknown before.

What problem does this paper attempt to address?

Thermal conductivity measurement of phase-change material near melting point based on perturbation method

ZHOU Tian,LIU Xu,SUN Zhiqiang,PENG Wei,ZHOU Jiemin

DOI: https://doi.org/10.11817/j.issn.1672-7207.2018.04.028

2018-01-01

Abstract:A new one-dimensional radial model was established based on the Stefan model. With the application of perturbation, the relationship between the thermal conductivity and the evolution of phase change interface was deduced. According to this relationship, a test system was designed to determine the thermal conductivity near the melting point of phase change materials. Barium hydroxide that was commonly used as materials in heat storage system was selected to obtain the thermal conductivity on the phase interface evolution at three boundary temperatures of 356, 361 and 366 K. The results show that the three average thermal conductivities are 0.673, 0.658 and 0.651 W?m?1?K?1, respectively. During the measurement, the control of boundary temperature is required, and the boundary heat flux needn't be measured, and multiple sets of thermal conductivity can be obtained from a single test with high accuracy, so the proposed method has good applicability.
Transient Performance of a Thermal Energy Storage-Based Heat Sink Using a Liquid Metal As the Phase Change Material

Li-Wu Fan,Yu-Yue Wu,Yu-Qi Xiao,Yi Zeng,Yi-Ling Zhang,Zi-Tao Yu

DOI: https://doi.org/10.1016/j.applthermaleng.2016.08.137

IF: 6.4

2016-01-01

Applied Thermal Engineering

Abstract:In this Technical Note, the use of a liquid metal, i.e., a low melting point Pb-Sn-In-Bi alloy, as the phase change material (PCM) in thermal energy storage-based heat sinks is tested in comparison to an organic PCM (1-octadecanol) having a similar melting point of similar to 60 degrees C. The thermophysical properties of the two types of PCM are characterized, revealing that the liquid metal is much more conductive while both have nearly identical volumetric latent heat of fusion (similar to 215 MJ/m(3)). By using at the same volume of 80 mL, i.e., the same energy storage capacity, the liquid metal is shown to outperform significantly over the organic PCM under the various heating powers up to 105.3 W/cm(2). During the heating period, the use of the liquid metal leads to a remarkable extension of the effective protection time to nearly twice longer as well as a reduction of the highest overheating temperature by up to 50 degrees C. The cool-down period can also be shortened significantly by taking advantage of the much higher thermal conductivity of the liquid metal. These findings suggest that liquid metals could serve as a promising PCM candidate for particular applications where the volume limit is very rigorous and the penalty in weight increment is acceptable. (C) 2016 Elsevier Ltd. All rights reserved.
A Novel Method for Determining the Melting Point, Fusion Latent Heat, Specific Heat Capacity and Thermal Conductivity of Phase Change Materials

Xiao-Hu Yang,Jing Liu

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2018.07.117

IF: 5.2

2018-01-01

International Journal of Heat and Mass Transfer

Abstract:In this paper, a novel method for determining the main thermophysical properties of phase change materials (PCM) is proposed, which can be called as "T-melting CHF" method. The melting point, fusion latent heat, thermal conductivity, and specific heat capacity in both solid and liquid phase of PCM, can all be obtained simultaneously by only one test. The theoretical fundamentals lying behind are introduced, the measurement apparatus and measurement principles are presented, and corresponding restrictive conditions for high accuracy measurement are provided. Theoretically, the thermophysical properties can be accurately measured by the proposed method if the test module can be perfectly insulated. However, heat loss inevitably exists in practical measurement, it will significantly influence the measuring accuracy, hence a correction method is proposed to improve this situation. A typical low melting point metal (gallium) and a typical organic PCM (n-eicosane) were tested to verify the feasibility and accuracy of the method. The experimental results agree well with the reference data reported in the literature. Compared with conventional measurement techniques, the method proposed here has advantages such as simple structure, low cost and high measurement speed; more importantly, it is able to measure multiple properties simultaneously. (C) 2018 Elsevier Ltd. All rights reserved.
A volume-shrinkage-based method for quantifying the inward solidification heat transfer of a phase change material filled in spherical capsules

Min-Jie Liu,Li-Wu Fan,Zi-Qin Zhu,Biao Feng,Han-Cong Zhang,Yi Zeng

DOI: https://doi.org/10.1016/j.applthermaleng.2016.08.027

IF: 6.4

2016-01-01

Applied Thermal Engineering

Abstract:In order to study quantitatively the inward solidification heat transfer of a phase change material (PCM) enclosed in spherical capsules, an experimental method was proposed in this Technical Note, which is based upon measurement on the instantaneous volume shrinkage of the PCM during solidification. The shrunk volume was compensated continuously by an extra amount of liquid PCM preserved in a tube, and the descending height in the tube was recorded to calculate the volume shrinkage. Other quantities of interest, solidification fraction and surface-averaged heat flux for example, were readily reduced as single-valued functions of the volume shrinkage. Using 1-tetradecanol as the PCM, the proposed method was realized in laboratory with a stainless steel spherical capsule having an inner diameter of approximately 60 mm. Parallel tests were carried out for a set of three boundary cooling temperatures. It was shown that the measured descending heights are reproducible and are in agreement with the theoretical maximum values approaching the end of solidification. The experimental results were then discussed with an emphasis on the transient variations of solidification and heat transfer. Correlations were obtained for both solidification fraction and surface-averaged Nusselt number with respect to the product of Fourier and Stefan numbers. (C) 2016 Elsevier Ltd. All rights reserved.
Measurements of the melting points, liquidus, and solidus of the Mo, Ta, and Mo Ta binary alloys using a novel high-speed pyrometric technique

V.B. Rajkumar,Yong Du,Shuhong Liu,Kaiming Cheng,Ajeet Kumar Srivastav

DOI: https://doi.org/10.1016/j.ijrmhm.2020.105335

IF: 4.804

2020-12-01

International Journal of Refractory Metals and Hard Materials

Abstract:<p>The measurement of high phase-transition temperature is equally challenging and useful for the development of high-temperature materials for critical applications. Pyrometer is a suitable option to measure phase-transition temperature above 2300 K. In this work, Mo, Ta, and their isomorphous binary alloys are selected as the target system for high-speed pyrometer temperature measurements in the arc-melting setup. The present phase transitions (melting point, solidus, and liquidus) measurements indicate that the MoTa is an isomorphous system with a narrow freezing range (i.e. an average value < 35 K). The results from this present work would change the existing MoTa phase diagram. The Gibbs energy modeling for liquid (L) and BCC_A2 (<em>α</em>) phases of the MoTa system is then performed including the latest experimental results from this work. The applications of the current experimental methodology could be extended to measure the high phase-transition temperatures in superalloys with significant commercial values.</p>

materials science, multidisciplinary,metallurgy & metallurgical engineering
Progress in Measuring Techniques and Thermal Radiative Properties of Metals at Cryogenic Temperatures: A Review

Hashmi Abdul Rehman,Bo Wang,Saadat Fatima,Zhihua Gan

DOI: https://doi.org/10.1016/j.cryogenics.2024.103950

IF: 2.134

2024-01-01

Cryogenics

Abstract:In recent years, the development in measurement techniques of thermal radiative properties has attracted much attention to cryogenic applications, including space exploration, cryogenic research, medical applications, instrument design, planetary exploration and remote sensing, cryogenic storage and transportation. This paper discusses the importance of emissivity/ absorptivity measurement, the factors they depend on, and the respective measurement methods, including calorimetric and radiometric. This paper also summarizes the published data on emissivity and absorptivity related to aluminum and stainless steel. It highlights the importance of surface treatment of materials, providing valuable insight into the significance of emissivity in cryogenic applications, which can serve as a reference for future research in this field.
Theoretical introduction to express way of the complex determination of the thermophysical parameters of metals

Yuri Kornyushin

DOI: https://doi.org/10.48550/arXiv.cond-mat/0703392

2007-03-15

Materials Science

Abstract:A method to measure thermophysical characteristics (TPC) of conductive materials is described. The method is based upon controlled bulk (e.g., Ohmic) heating and measurement of the averaged over the volume of a sample temperature and the temperature of the surface of a sample. To measure averaged over a sample volume temperature a dilatometric technique could be used and surface temperature could be measured by x-ray method. This allows one to avoid distortion of the temperature field by the thermocouples and directly takes into account heat losses from the surface of a sample. The treatment of the experimental data should be based upon theoretical calculations presented in this paper. The measured values of the averaged over the volume of a sample temperature and a surface temperature allow for the calculation of TPC of the material. The experimental data obtained on the iron-based materials prove the high accuracy of the described approach [1-3].
A simple method, the -history method, of determining the heat of fusion, specific heat and thermal conductivity of phase-change materials

zhang yinping,jiang yi

DOI: https://doi.org/10.1088/0957-0233/10/3/015

IF: 2.398

1999-01-01

Measurement Science and Technology

Abstract:A simple method of determining the melting point, heat of fusion, specific heat and thermal conductivity of phase-change materials (PCMs) is presented. Compared with other methods, such as conventional calorimetric methods, differential thermal analysis and differential scanning calorimetry methods, it has the following salient features: the experimental unit is simple, able to measure the heat of fusion, specific heat and thermal conductivity of several samples of PCMs simultaneously and allows one to observe the phase-change process of each PCM sample. Using the method, the thermophysical properties of various salt hydrates, paraffin and some PCMs developed by us were measured. For the PCMs whose thermophysical properties are available in the literature, our results gave fairly good agreement. The method is especially useful for the selection of lots of candidate PCMs used for the purpose of engineering and for preparing new PCMs.
A New Noncontact Probe for Thermophysical Properties of Solid Surfaces

JW Fang,QR Yin,SY Zhang,ZN Zhang,XJ Shui

DOI: https://doi.org/10.1088/0256-307x/17/9/004

2000-01-01

Abstract:Based on the photothermal displacement effect and the optical diffraction effect, an alternative pulsed photothermal technique has been developed. This technique overcomes some disadvantages of conventional methods and provides a sensitive, noncontact and nondestructive probe of the transient thermal and mechanical process at solid and thin him surfaces. Meanwhile, a three-dimensional theoretical model has also been presented to describe the experimental phenomena. Excellent agreement between the theory and the experiment is obtained. As an example, the technique is demonstrated by measuring the thermal diffusivity of aluminum and brass thin plates.
Combined measurement and calibration method for the thermal conductivity of phase change materials

Aichun Ma,Chenghan Cai,Shiyice Peng,Tian Zhou

DOI: https://doi.org/10.1016/j.ijthermalsci.2022.107987

IF: 4.779

2023-02-01

International Journal of Thermal Sciences

Abstract:A combined method for determining the thermal conductivity of phase-change materials (PCMs) is proposed in this paper. A primary concern for this method is mitigating the effect of factors that exist in real experiments but are excluded in the measurement model. Thus, a measurement model was proposed to establish the mathematical relationship between the thermal conductivity and liquid fraction during the melting process. An experimental system was developed, and two different PCMs were used for the experiment. The thermal conductivity obtained via the experiments depicted an increasing trend during the entire melting process; these measurements were treated as the effective thermal conductivity of the PCM. The enhanced heat transfer rate prompted by natural convection was identified as the factor that affected the thermal conductivity measurement; a numerical calibration approach was presented to mitigate this influence. The numerical model considered all factors influencing the errors, and thermal conductivities were obtained via repeated iterations. Deviations between the calibrated thermal conductivity and reference data were less than 8%, meeting the practical requirements of engineering applications.

engineering, mechanical,thermodynamics
Measurement principles for room temperature liquid and fusible metals' surface tension

Stephan Handschuh-Wang,Ben Wang,Tao Wang,Florian J. Stadler

DOI: https://doi.org/10.1016/j.surfin.2023.102921

IF: 6.2

2023-05-13

Surfaces and Interfaces

Abstract:Liquid and fusible metals have garnered considerable attention in the scientific community and industry due to a fascinating combination of thermophysical properties, namely, thermal and electrical conductivity and low phase transition temperature. Above this temperature, they are essentially liquids featuring a "high" surface tension. Such metals and alloys are potent materials for welding, soldering, and thermal transport. For these applications, an accurate knowledge of the surface tension and its temperature coefficient is of utmost importance. In the past decades, several measurement methods have been adapted and improved to measure the surface tension of liquid metals. Yet, for a specific metal/alloy and temperature system, one prefers some systems over others. This review explains the main measurement principles, sheds light on the reasons for favoring some methods over others, and briefly introduces the challenges associated with liquid metal's surface tension measurements.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Thermophysical properties in the Al-Cu-Ag system: A combined CALPHAD and first-principles study

Bo Jin,Shuhong Liu,Kai Xu,Qiang Lu,Yong Du

DOI: https://doi.org/10.1016/j.molliq.2022.121001

IF: 6

2022-12-15

Journal of Molecular Liquids

Abstract:Thermophysical properties play an essential role in the microstructure simulation during precipitation and solidification processes in materials science and engineering. In this work, a comprehensive investigation on the molar volume and surface tension of the Al-Cu-Ag ternary system was performed by the CALPHAD (CALculation of PHAse Diagram) approach and the first-principles calculation. Based on the critical review of experimental and theoretical data, the molar volume description of pure Ag in the liquid phase, and subsequently the mole fraction dependent thermophysical databases of molar volume and surface tension for the Al-Cu-Ag system including metastable phases were constructed via the CALPHAD approach. Then considering the excess molar volume, the surface tension of solution alloys could be predicted by the Butler equation using a home-made code with the input of thermodynamic and thermophysical parameters. With the increment of temperature, molar volume of the alloys increases while the surface tension decreases. All the calculated results using the present parameters are in satisfactory agreement with the corresponding experimental data, which could be subsequently applied to simulate the microstructure evolution like precipitation kinetics and phase-filed simulation.

chemistry, physical,physics, atomic, molecular & chemical
An On-Line System for High Temperature Dielectric Property Measurement of Microwave-Assisted Sintering Materials

Li Wu,Yi Zhang,Fengxia Wang,Weiquan Ma,Tian Xie,Kama Huang

DOI: https://doi.org/10.3390/ma12040665

2019-02-22

Abstract:Microwave-assisted sintering materials have been proven to deliver improvements in the mechanical and physicochemical properties of the materials, compared with conventional sintering methods. Accurate values of dielectric properties of materials under high temperatures are essential for microwave-assisted sintering. In view of this, this paper, proposes an on-line system to measure the high temperature dielectric properties of materials under microwave processing at a frequency of 2450 MHz. A custom-designed ridge waveguide is utilized, where samples are heated and measured simultaneously. An artificial neural network (ANN) trained with the corresponding simulation data is integrated into this system to reverse the permittivity of the measured materials. This whole system is tested at room temperature with different materials. Accuracies of measuring dielectric property with an error lower than 9% with respect to theoretical data have been achieved even for high loss media. The functionality of the dielectric measurement system has also been demonstrated by heating and measuring Macor and Duran ceramic glass samples up to 800 °C. All the preliminary experiments prove the feasibility of this system. It provides another method for dielectric property measurement and improves the understanding of the mechanism between microwave and media under high temperatures, which is helpful for optimizing the microwave-assisted sintering of materials.
Development of Multi-Physical Properties Comprehensive Measurement System for Micro/nanoscale Filamentary Materials

ZHANG Xing,SHI XuGuo,MA WeiGang

DOI: https://doi.org/10.1360/n092018-00018

2018-01-01

Scientia Sinica Technologica

Abstract:The properties of micro/nanoscale filamentary materials are significantly different from bulk. They have wide applications in MEMS/NEMS sensors and micro/nano electrical devices. As the measurement methods for bulk materials are difficult to be applied on nanoscale filamentary materials, development of the precise measurement method and technology for micro/nanoscale filamentary materials has been attracting intense interest. This paper developed a highly integrated measurement system for comprehensively measuring the thermophysical, electrical and thermoelectric properties of micro/nanoscale filamentary materials from 40 K to 500 K, including electrical conductivity, temperature coefficient of resistance, thermal conductivity, thermal diffusivity, thermal effusivity, specific heat, Seebeck coefficient and the figure of merit. A detailed uncertainty analysis has been evaluated and Platinum wire (99.95%) and constantan wire (60% Cu 40% Ni) have been measured and compared with reference values to verify the accuracy of the measurement system. Development of the present system is expected to fill the international gaps in development of multi-physical properties comprehensive measurement system for nanoscale filamentary materials.
Thermodynamic Temperature Measurements of Silver Freezing Point and Htfps

Z. Yuan,X. Lu,X. Hao,W. Dong,T. Wang,Y. Lin,J. Wang,Y. Duan

DOI: https://doi.org/10.1063/1.4821371

2013-01-01

Abstract:The hybrid method, by introducing a lens to the irradiance method, was adopted to measure the thermodynamic temperature at NIM. An absolute radiation thermometer was established with two alternative filter radiometers (633nm and 900nm). The parameters of the absolute radiation thermometer were calibrated. The thermodynamic temperatures of the silver fixed point and Co-C, Pt-C, Re-C were determined. The uncertainties were 0.24K to 0.94K for FR633 and 0.34K to 1.6K for FR900 from the silver point to Re-C. The results were compared with the ITS-90 values and show a good agreement: 0.18K at Co-C, -0.11K at Pt-C and -0.24K at Re-C, which are under the estimated uncertainties.
Integrating computational and experimental thermodynamics of refractory materials at high temperature

Qi-Jun Hong,Axel van de Walle,Sergey V. Ushakov,Alexandra Navrotsky

DOI: https://doi.org/10.1016/j.calphad.2022.102500

2022-11-27

Abstract:We develop new computational and experimental methods to determine materials properties at high temperature, such as melting temperature, heat of fusion, heat capacity, and lattice constant. From density functional theory, we construct the small-size coexistence method and the SLUSCHI package to compute the properties accurately, as well as to fully automate the computation process. From experiment, we build experimental approaches, including ultra-high-temperature Drop-n-Catch (DnC) calorimetry and synchrotron X-ray diffraction on solid laser-heated aerodynamically levitated samples. Employing deep learning techniques, we build an ensemble graph-neural-networks model that predicts materials properties in milliseconds. The simultaneous development of computational and experimental approaches allows us to integrate these methods and the data generated by them.
A high-precision method to measure thermal conductivity of solids using reversible heat flux

Ping Zhang,Bo Shi,Yimin Xuan,Qiang Li

DOI: https://doi.org/10.1088/0957-0233/24/9/095004

IF: 2.398

2013-01-01

Measurement Science and Technology

Abstract:In the thermal conductivity measurement of solids using the traditional steady-state methods, it is observed that the test results differ from their standard values when only one directional heat flux is introduced. Analysis of the results shows that the additive errors are considerable and cannot be ignored. To minimize the additive errors, a high-precision method by alternating the direction of heat flux in steady-state thermal conductivity measurement of solids is proposed. In this method, the additive errors are diminished by using the data corresponding to both forward and reverse heat flux. Meanwhile, a modified thermal instrument is designed and established to measure the thermal conductivity of solids. Simultaneous calibration of the thermal instrument has been processed to improve the measurement accuracy of temperature readings. The thermal conductivities of samples 99.999% standard pure copper and Elkonite copper-tungsten alloy 30W3 are measured and compared with their reference values to verify the accuracy of the method. The results indicate that the processing data well match the reference values.
Precise Measurements of Thermophysical Properties of Liquid Ti–6Al–4V (Ti64) Alloy On Board the International Space Station

Markus Mohr,Rainer Wunderlich,Rada Novakovic,Enrica Ricci,Hans-Jörg Fecht

DOI: https://doi.org/10.1002/adem.202000169

IF: 3.6

2020-04-30

Advanced Engineering Materials

Abstract:The Titanium alloy Ti‐6Al‐4V (Ti64) is a very widely applied alloy with extreme importance in the fields of aerospace, automotive and biomedicine. For a large range of manufacturing methods that involve the liquid phase, such as casting, metal injection molding, thermal spraying and additive manufacturing, process simulations are an important tool for the optimization and development of the fabrication process. Reliable thermophysical property data of Ti64 in the solid and the liquid phase are necessary inputs to such models. Due to the high melt reactivity of titanium alloys with container materials, measurements performed using conventional thermophysical equipment are usually impossible. We present precise benchmark measurement of thermophysical properties (surface tension, viscosity, specific heat, total hemispherical emissivity, thermal conductivity, electrical resistivity, mass density) of Ti64 in the undercooled liquid phase using containerless electromagnetic levitation on board the international space station (ISS). We compared the obtained values to predictive models, that can help to analyze the data for other compositions of the alloy system. The property values can be applied to simulations of industrial fabrication processes, in order to optimize these processes and thus, the product quality.This article is protected by copyright. All rights reserved.

materials science, multidisciplinary
Low Melting Point Liquid Metal As a New Class of Phase Change Material: an Emerging Frontier in Energy Area

Haoshan Ge,Haiyan Li,Shengfu Mei,Jing Liu

DOI: https://doi.org/10.1016/j.rser.2013.01.008

IF: 16.799

2013-01-01

Renewable and Sustainable Energy Reviews

Abstract:The application of phase change materials (PCMs) grew rapidly in the last few years, especially in those areas like solar energy, thermal comfort control, green building, environmental conservation and electronic cooling etc. Tremendous efforts have therefore been made on finding new powerful PCMs or improving performance of the currently available PCMs which generally subject to inherent defects, such as low thermal conductivity, poor stability after millions of repeated solidifying and melting processes, easy phase separation during transition and narrow temperature span between the melting point and the evaporation state. To better serve for the stringent request from many emerging utilization situations, this article is dedicated to systematically present a new class of high performance PCM, the low melting point liquid metals or their alloys, which were seldom addressed before. The unique merits, application features and potential values of these highly conductive liquid like materials were summarized with their basic properties interpreted. Some latest advancement made in the area was discussed for illustration purpose. Comparative evaluation on the fundamental mechanisms and practical issues between conventional PCMs and the low melting point metal PCM was carried out. Further, some involved scientific and technical challenges were raised. The present work is expected to incubate an emerging frontier towards studying and utilizing metal PCMs in the coming time, which is rather useful for a broad range of energy areas.
Experimental measurement of thermal diffusivity, conductivity and specific heat capacity of metallic powders at room and high temperatures

Faiyaz Ahsan,Jafar Razmi,Leila Ladani

DOI: https://doi.org/10.1016/j.powtec.2020.07.043

IF: 5.64

2020-09-01

Powder Technology

Abstract:Because of the complications associated with metal additive manufacturing process, comprehensive modeling is done to improve the process. Thermo-physical properties such as heat capacity, thermal conductivity and diffusivity of metallic powder is very crucial for the models to be accurate. Due to challenges associated with measuring these properties at high temperature, available analytical models are often used to determine these temperature dependent thermo-physical properties. This study is conducted to fill this gap and provide experimental information that has been missing from the bulk of the literature for variety of metallic powders commonly used in additive manufacturing processes. Additionally, a comparison between these experimental data and analytical models are conducted to determine the correlation and accuracy of these models. Analysis revealed that all the thermal properties of the powders show a non-monotonic behavior at high temperature. A regression analysis is conducted to predict thermal conductivity at higher temperatures.

engineering, chemical

A New Measurement System for Thermophysical Properties

Thermal conductivity measurement of phase-change material near melting point based on perturbation method

Transient Performance of a Thermal Energy Storage-Based Heat Sink Using a Liquid Metal As the Phase Change Material

A Novel Method for Determining the Melting Point, Fusion Latent Heat, Specific Heat Capacity and Thermal Conductivity of Phase Change Materials

A volume-shrinkage-based method for quantifying the inward solidification heat transfer of a phase change material filled in spherical capsules

Measurements of the melting points, liquidus, and solidus of the Mo, Ta, and Mo Ta binary alloys using a novel high-speed pyrometric technique

Progress in Measuring Techniques and Thermal Radiative Properties of Metals at Cryogenic Temperatures: A Review

Theoretical introduction to express way of the complex determination of the thermophysical parameters of metals

A simple method, the -history method, of determining the heat of fusion, specific heat and thermal conductivity of phase-change materials

A New Noncontact Probe for Thermophysical Properties of Solid Surfaces

Combined measurement and calibration method for the thermal conductivity of phase change materials

Measurement principles for room temperature liquid and fusible metals' surface tension

Thermophysical properties in the Al-Cu-Ag system: A combined CALPHAD and first-principles study

An On-Line System for High Temperature Dielectric Property Measurement of Microwave-Assisted Sintering Materials

Development of Multi-Physical Properties Comprehensive Measurement System for Micro/nanoscale Filamentary Materials

Thermodynamic Temperature Measurements of Silver Freezing Point and Htfps

Integrating computational and experimental thermodynamics of refractory materials at high temperature

A high-precision method to measure thermal conductivity of solids using reversible heat flux

Precise Measurements of Thermophysical Properties of Liquid Ti–6Al–4V (Ti64) Alloy On Board the International Space Station

Low Melting Point Liquid Metal As a New Class of Phase Change Material: an Emerging Frontier in Energy Area

Experimental measurement of thermal diffusivity, conductivity and specific heat capacity of metallic powders at room and high temperatures