Abstract:We propose a novel laser configuration that can output 3.5-$\mu$m nanosecond laser pulses based on a simple and monolithic fiber structure. Cascade-gain-switching, which converts the wavelength of nanosecond pulses from 1.55 $\mu$m to 3.5 $\mu$m by two successive gain-switching processes. Instead of using expensive pump sources at special wavelengths and bulky active or passive modulation elements for Q-switching or mode-locking, the cascade gain-switching only requires the pumping of an electric-modulated 1.55-$\mu$m pulsed laser and two continuous-wave (CW) 975-nm laser diodes. They are all standard products for fiber optic communication applications, which can greatly lower the cost of mid-infrared laser pulse generation. To investigate the feasibility of this configuration, we numerically simulated the cascade-gain-switching processes by comprehensive rate-equation models. In single-shot regime, for stable 3.5-$\mu$m pulsed lasing, the CW 975-nm pump should be turned on at least $\sim500$ $\mu$s ahead of the 1.55-$\mu$m pulsed pump. It shows that the pulse width of the 1.55-$\mu$m pump has major impact on the temporal shape of the intermediate 1.97-$\mu$m pulse while has neglected influence on the generated 3.5-$\mu$m pulse. On the other hand, increasing the CW pump power can significantly improve the output peak power and shorten the pulse when the pump power is less than $\sim4$ W. In the repetitive-pulse regime, we found the 3.5-$\mu$m pulse train can be stably outputted when the repetition rate is $<=100$ kHz. As the repetition rate increases, the duration of reaching the stable operation increases. When the repetition rate is large than 100 kHz, the stable operation cannot be established because the rate of consuming the population on the $^4I_{11/2}$ level of $Er^{3+}$ ions is faster than the rate of building the population.

Cascade-gain-switching Hybrid-Pumping for Generating 3.5-Um Nanosecond Pulses from Monolithic Fiber Lasers

Cascade-gain-switching for generating 3 . 5-μ m nanosecond pulses from low-cost monolithic fiber lasers

Cascade-gain-switching for generating 3.5-um nanosecond pulses from monolithic low-cost fiber lasers

Nonlinearity Optimization of Dissipative-Soliton Fiber Laser for Generation of Pulses with 350 Kw Peak Power

Gain-Switched Er-Doped Fluoride Fiber Laser at ~3.75 μm

Hybrid Structure Laser Based on Semiconductor Nanowires and a Silica Microfiber Knot Cavity

Nanosecond-pulse High-Peak-power Circle-Focusing Laser Beam for Laser Processing

Compact hybrid laser based on semiconductor nanowires and a silica biconical fiber

Pump quantum efficiency optimization of 3.5 μm Er-doped ZBLAN fiber laser for high-power operation

High Power Efficient 3.81 $\mu{\rm M}$ Emission from a Fiber Laser Pumped Aperiodically Poled Cascaded Lithium Niobate

1.7 µm gain-switched and mode-locked hybrid Tm-Ho codoped fiber laser signal generation and optimization

Modeling of A Cascaded Mid-Infrared Fiber Laser at 2.78 μm and 3.44 μm Dual-Wavelength Pumped at 0.98 μm and 1.15 μm

Generation of Nanosecond 2.65 Μm Pulses and Pulse Narrowing in Fiber-Bulk Ho3+:YAG Laser Pumped Gain-Switched Cr2+:CdSe Laser

Mid-infrared ultrashort pulses generated from a hybrid mode-locked Er:ZBLAN fiber laser

Sub-50 fs pulses generation from an all-fiber monolithic gain-managed nonlinear amplifier with CFBG-based pre-compressor

1010 nm Directly LD-Pumped 6kW Monolithic Fiber Laser Employing Long-Tapered Yb3+-Doped Fiber

Femtosecond Red and Near-Infrared Lasers Due to Cascaded-Raman-Assisted Four-Wave Mixing in a Nonlinear Yb-Doped Fiber Amplifier

All-fiber 30-μm core diameter Yb-doped pulse-pumped amplifier cascade generating 10 nm-bandwidth 545 kW peak power pulses

30 W Output of Short Pulse Duration Nanosecond Green Laser Generated by a Hybrid Fiber-Bulk MOPA System

A 4.8-kW high-efficiency 1050-nm monolithic fiber laser amplifier employing a pump-sharing structure

All-Fiber Millijoule Energy and Nanoseconds Pulse Operation of A High Beam Quality Multi-Stage Pulse-Pumped Yb-Doped Amplifier Cascade