Abstract:This study delves into the effects of quenching methods on 30MnB5NbTi hot stamping steel, revealing that water quenching significantly outperforms die, oil, and air cooling in enhancing ultimate tensile (UTS) and yield strengths (YS). Through detailed scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM) analyses, it showcases the microstructural evolution toward a finer martensitic lath structure, underpinning the superior mechanical performance achieved. The effects of different quenching methods on the microstructure and mechanical properties of 30MnB5NbTi hot stamping steel are investigated, and the quenched microstructure is characterized by scanning electron microscope (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). The mechanical properties are evaluated by uniaxial tensile test. The results reveal that, in comparison to die quenching, oil quenching, or air cooling, water‐quenched samples (tempered after water quenching, die quenching and oil quenching) exhibit the highest ultimate tensile strength (UTS) and yield strength (YS), reaching 2052 and 1422 MPa, respectively. Various quenching methods enable multi‐level strength control for the same steel grade, achieving a strength control range of ≈1000 MPa. The microstructure of samples quenched by water, die, and oil is fully martensite, and martensite exhibited block and lath morphology. With the increase of cooling rate, martensite laths become finer and the prior austenite size decreased. The microstructure of air‐cooled samples is martensite, ferrite, and retained austenite. The strengthening mechanisms of different quenched samples are calculated. The results show that dislocation strengthening and precipitation strengthening are the two dominant strengthening mechanisms in 30MnB5NbTi hot stamping steel. Therefore, the properties of hot stamping steel can be improved by changing the cooling rate by designing physical dies.

Effect of Water Quench Process on Mechanical Properties of Cold Rolled Dual Phase Steel Microalloyed with Niobium

Effects of heat treatment process on microstructure and magnetic properties of cold rolled dual phase steel

The Effect of Direct Quenching on the Microstructure and Mechanical Properties of NiCrMo and Cu-Bearing High-Strength Steels

Effect of Different Water Toughening Treatment on Mechanical Properties and Microstructure of Fe-Mn-C TWIP Steel

Effect of Different Heat Treatment Processes on Microstructures and Mechanical Properties of DP Steels

On the use of thermomechanical processing to enhance the strength-ductility-toughness balance of plain low-carbon steel

Effect of Double Quenching on Microstructure and Impact Toughness of a High Strength Low Alloy Steel

On the Simultaneous Improving of Strength and Elongation in Dual Phase Steels via Cold Rolling

Effect of Different Quenching Methods on the Microstructure and Mechanical Properties of 30MnB5NbTi

Effect of Hot Rolled Cooling Process on Structure and Properties of Nb-Ti Microalloy Dual Phase Steel

Effect of Nb and Cu on the Microstructure and Hardness of Quenching–partitioning–tempering Dual-Phase Steels

Characterization of Microstructure and Mechanical Properties of a Nb-Microalloyed Steel after Quenching-Partitioning-Tempering Process

Effect of Dissolved and Precipitated Niobium in Microalloyed Steel on Deformation Induced Ferrite Transformation (Dift)

The effect of the increased strain per pass during the hot-rolling and its effect on the tensile properties of V-Mo and Cr-V-Mo microalloyed dual-phase steels

High Strength-Ductility Nb-microalloyed Low Martensitic Carbon Steel: Novel Process and Mechanism

Effect of Process Parameters on Microstructural Evolution and Grain Refinement in a Low Carbon High Strength Microalloyed Dual Phase Steel

Effect of Nb on Microstructural Evolution and Mechanical Properties of Hot‐Rolled Quenching and Partitioning Steels Containing Bainite

Effect of Intercritical Heat Treatment on Microstructure, Nano-Size Precipitation and Mechanical Properties of Fe–Ni–Cu–Al Low Carbon Steel

Effects of NiAl Precipitation on the Stability of Retained Austenite and Mechanical Properties of a Quenching-partitioning-tempering Treated Medium-manganese Steel

Impact of Niobium Addition and Non-Metallic Inclusions' Characteristics on the Microstructure and Mechanical Properties of Low-Carbon CrNiMnMoB Ultrahigh-Strength Steel: A Comprehensive Investigation

Simultaneous enhancement of strength and ductility in ferrite-martensite steel via increasing the martensite fraction