Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effect of Deformation of Fiber in the PET on the Oynamic Mechanical Property

Effects of Physical Aging on Thermomechanical Behaviors of Poly(ethylene Terephthalate)-Glycol (PETG)

Effects of stretching on crystalline phase structure and morphology of hard elastic PVDF fibers

The Effect Of Pore Size Deformation On Multi-Pore Model Of Woven Geotextiles In Tension Test

Optimizing Physical Aging in Poly(ethylene Terephthalate)-Glycol (PETG)

Effect of heat treatment on the mechanical properties of PBT/PET yarn

Study on Silk Fibroin Coated PET Fabric

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Effect of drawing and heat‐setting process on aggregate structure of Poly(ethylene terephthalate) industrial fiber in large‐scale spinning production

Preparation of High-Modulus and High-Strength Poly(Ethylene-Terephthalate) Fiber by Zone Annealing

Effect of Boiling and Stretching on the Optical and Mechanical Properties of Polyester Fibres

Anisotropy of Dynamic Viscoelasticity for Uniaxially Drawn Poly(Ethylene-Terephthalate) Films and Its Temperature-Dependence

The effects of UV aging process on the structure and properties of high-tenacity poly(ethylene terephthalate) industrial fiber

Effect of Thermal and Mechanical Processes on the Molecular Orientation of Polyester Fibres

The effect of short heat treatment on different properties of PET fiber using double beam interference microscopy

Effect of Heat-Setting Temperature on the Structure and Properties of BOPET Film

Structure and Rheological Behavior of PET/WSPET Blend

Effect of Alkali Treatment on Morphological Structure and Mechanical Properties of PTT Fiber

INFLUENCE OF HEAT-TREATMENT ON MECHANICAL PROPERTY OF GLASS FIBER REINFORCED POLY(ETHYLENE TEREPHTHALATE)

Thermomechanical deformation of polyethylene-terephthalate artificial muscles