Abstract:One of the useful features of 3D-printed specimens of recycled polyethylene terephthalate glycol (R-PETG) is the ability to repetitively develop free recovery as well as the work-generating, shape-memory effect. This behavior is enabled by the R-PETG's capacity to stiffen during cooling, thus allowing for a new temporary shape to be induced. Aiming to devise an explanation for the polymer's stiffening, in this study, the variation in some of the R-PETG's parameters during cooling are emphasized and discussed. The evolution of an R-PETG filament's shape was monitored during room-temperature-bending heating-cooling cycles. Straight-shape recovery and the complete loss of stiffness were observed at the start and the end of heating, respectively, followed by the forced straightening of the filament, performed by the operator, around 40 °C, during cooling. The tests performed by dynamic mechanical analysis disclosed the rise of the storage modulus (E') after 100 °C heating followed by either liquid-nitrogen- or air-cooling to room temperature, in such a way that E' was always larger after cooling than initially. Static tests emphasized a peculiar stress variation during a heating-cooling cycle applied in air, within the heating chamber of the tensile testing machine. Tensile-failure tests were performed at -10 °C at a rate of 100 mm/min, with specimens printed at various deposition directions between 10 and 40° to the transversal direction. The specimens printed at 40°, which had the largest ultimate strains, were broken with tensile rates between 100 and 500 mm/min. Deformation rate increase favored the shift from crazing to delamination failure modes. The correlation between the structural changes, the sharp E' increase on heating, and the stiffening induced by cooling represents a novel approach that enables the use of 3D-printed R-PETG for the fabrication of the active parts of low-priced lightweight resettable actuators.

Thermomechanical deformation of polyethylene-terephthalate artificial muscles

Modeling the Effect of Physical Aging on the Stress Response of Amorphous Polymers Based on a Two-Temperature Continuum Theory

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

Optimizing Physical Aging in Poly(ethylene Terephthalate)-Glycol (PETG)

Effects of Physical Aging on Thermomechanical Behaviors of Poly(ethylene Terephthalate)-Glycol (PETG)

Mechanisms of Multi-Shape Memory Effects and Associated Energy Release in Shape Memory Polymers

A Predictive Parameter for the Shape Memory Behavior of Thermoplastic Polymers

Morphology modulation of artificial muscles by thermodynamic-twist coupling

Thermo-Mechanical and Creep Behaviour of Polylactic Acid/Thermoplastic Polyurethane Blends

A simple analytical thermo-mechanical model for liquid crystal elastomer bilayer structures

Transient thermo-mechanical analysis for bimorph soft robot based on thermally responsive liquid crystal elastomers

Electrothermally actuated artificial muscles from the silver-polyethylene-terephthalate core–shell structure

Significantly improved electromechanical performance of dielectric elastomers via alkyl side-chain engineering

Effect of temperature on the programmable helical deformation of a reconfigurable anisotropic soft actuator

Effective On-Line Performance Modulation and Efficient Continuous Preparation of Ultra-Long Twisted and Coiled Polymer Artificial Muscles for Engineering Applications

Variations in the Thermomechanical and Structural Properties during the Cooling of Shape-Memory R-PETG

Construction of Twisted/Coiled Poly(lactic acid) Fiber-Based Artificial Muscles and Stable Actuating Mechanism

Thermal Torsion Effect of Twisted Polymer Actuators

Thermo-mechanical deformation for thermo-induced shape memory polymers at equilibrium and non-equilibrium temperatures: Experiment and simulation

Analysis, Modeling and Experimental Validation of Temperature-Changing Effect on Mechanical Properties of Pneumatic Artificial Muscle.

Linear viscoelasticity, nonlinear rheology and applications of polyethylene terephthalate vitrimers