Abstract:High-energy ball milling represents an efficient process for producing composite powders consisting of ceramic particles dispersed in a metallic matrix. However, collision events, plastic deformations, and cold welding during the milling lead to a flake or block-like shape of the resulting composite powders. Further consolidation of such irregularly shaped powders by powder bed-based additive manufacturing technologies can be challenging because of their low flowability and low bulk density. In this work, different approaches, including milling process parameters (speed, process control agent atmosphere) and post-treatments (mechanical and thermal), are investigated on their suitability to influence the particle shape, especially concerning the roundness of the composite powders consisting of the aluminum alloy AlSi10Mg with 5 vol% SiC and Al2O3 reinforcement. It is found that milling with menthol as a process control agent leads to the finest composite powder compared to other milling parameters, with the lowest particle roundness of 0.39 (initial powders 0.84). No success in rounding the milled composite powder could be achieved through mechanical post-treatment in a planetary ball mill. On the other side, the thermal spraying of, e.g., SiC reinforced AlSi10Mg powder resulted in a 77–82% relative roundness. A remarkable change in the microstructure and the shape of the composite powders could also be observed after heat treatment in tube furnaces at a temperature above the melting point of AlSi10Mg. The best result in terms of improved roundness (relative to around 85%) was obtained for Al2O3 reinforced at 600 °C. A further increase of the temperature to 700 °C resulted in a moderate coarsening of powders with Al2O3 and extensive sintering of powders with SiC, presumably due to a different distribution inside the matrix.

The Microstructure and Properties of Fine Crystalline Al-50Si Alloy Prepared by High-Energy Ball Milling

Microstructure and Electromagnetic Properties of Fe-Si-Al Flakes Produced from Melt-Spun Ribbons

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Mechanical milling and its influence on microstructure and electric conductivity of high mass fraction TiC / Cu composites

Amorphization in the AlC System by Mechanical Alloying

Formation of Nanocrystalline Fcc Phase by Mechanically Driven Crystallization

Fabrication of Nano-Sic_p/al Composite by High Energy Ball Milling

The evolution of microstructure and magnetic properties of Fe–Si–Al powders prepared through melt-spinning

Effect of Ball Milling Time on the Microstructure and Properties of High-Silicon–Aluminum Composite

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Structure Investigation of Ball Milled Composite Powder Based on AlSi5Cu2 Alloy Chips Modified by Sic Particles

Effects of high-energy ball milling on structure and mechanical properties of L12 intermetallic compound Al67Mn8Ti25

EFFECTS OF HIGH-ENERGY BALL MILLING ON THE STRUCTURE AND PROPERTY OF A MULTIPHASE Al3Ti-BASED INTERMETALLIC ALLOY

Spark Plasma Sintering Cobalt Base Superalloy Strengthened by Y–Cr–O Compound Through High-Energy Milling

Influencing the Size and Shape of High-Energy Ball Milled Particle Reinforced Aluminum Alloy Powder

Structural and thermal properties of the Fe-based alloys prepared by mechanical milling

Superstructure in nano-crystalline Al50Cu28Fe22 alloy

Properties of High-Entropy Fe30Co20Ni20Mn20Al10 Alloy Produced by High-Energy Ball Milling

Effect of high energy ball milling on displacement reaction and sintering of Al−Mg/SiO2 composite powders

Effect of mechanical milling on microstructure evolution and mechanical properties of Al–Zn–Mg–Cu–Si alloy fabricated via spark plasma sintering

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites