Abstract:Microstructured optical fibers (MOFs) have been widely utilized for optofluidic waveguides, in which the micro-holes along the MOFs act as microfluidic channels for various applications such as supercontiuum sources and aqueous solution sensors. The air hole diameter of MOFs is generally several microns to tens of microns, which is much smaller compared with traditional fluid-core fiber waveguide. However, for specific applications such as ultra-trace analysis and low-threshold fluidic lasers, this channel dimension is still relatively large. The slot waveguide could confine light in a subwavelength-scale channel, however, the short propagation length and high loss of the waveguide may limit its applications. Here we propose an approach to achieve low-loss subwavelength-scale optofluidic waveguide in MOFs. As shown in Fig. 1(a), the hollow-core of the MOF is tapered down to a subwavelength-scale, and then the MOF is selectively infiltrated with aqueous solution. So light could be confined in an aqueous core surrounded by a tapered air-silica cladding. As the refractive index of the cladding is close to that of air, the index contrast between the fluidic core and the cladding is high enough to provide an efficient index-guiding in a subwavelength-scale core. The mode pattern of a fundamental mode in a tapered aqueous core MOF is calculated when the core diameter is 600nm (Fig. 1(b)). As shown in Fig. 1(c), we compare our tapered air-silica cladding with Teflon cladding. At the wavelength of 633 nm, the light with the fraction of power over 65% could be guided in the aqueous core with the size of 600 nm, which is 4 times higher than that in a core surrounded by a Teflon cladding, which has an overlap fraction of only 15.7%. So the method we propose has obvious advantages over the traditional method using Teflon material. It provides a novel platform for low-loss subwavelength-scale fluid-core guiding with the long interaction length, and therefore have various potential applications.

TWO-PHASE STRATIFIED FLOW OF LIQUID AND AIR IN PDMS MICROFLUIDIC CHANNELS FOR OPTOFLUIDIC WAVEGUIDES

Femtosecond Laser Engraved 2D Tunable Optofluidic Liquid Core/Air Cladding Channel Waveguides on PDMS

Flexible fluidic lens with polymer membrane and multi-flow structure

In Situ Fabrication of a Tunable Microlens.

A Compact Optofluidic Cytometer with Integrated Liquid-Core/pdms-cladding Waveguides.

High Index Contrast Subwavelength-Scale Optofluidic Waveguide in Mofs

Switchable 3D Optofluidic Y-branch Waveguides Tuned by Dean Flows

Acoustofluidic Waveguides for Fabrication of Localized Polymeric Microstructure Arrays

Preparation of hybrid soda-lime/quartz glass chips with wettability-patterned channels for manipulation of flow profiles in droplet-based analytical systems.

Versatile Optofluidic Solid-Core/Liquid-Cladding Waveguide Based on Evanescent Wave Excitation

Two-Phase Microfluidic Flow Modeling in an Electrowetting Display Microwell

Optic Imaging Of Single And Two-Phase Pressure-Driven Flows In Nano-Scale Channels Dagger

Optofluidic Microchannels in Aerogel

Polymer-loaded Hybrid Plasmonic Waveguides Leveraging Liquid Cores for Ultra-Low-loss Light Guiding

Optofluidics in Microstructured Optical Fibers

High-efficient Subwavelength-Scale Optofluidic Waveguides with Tapered Microstructured Optical Fibers

Three-Dimensional Opto-Fluidic Devices Fabricated by Ultrashort Laser Pulses for High Throughput Single Cell Detection and Processing

Low-loss optofluidic waveguides in fused silica enabled by spatially shaped femtosecond laser assisted etching combined with carbon dioxide laser irradiation

Thermal-Responsive Anisotropic Wetting Microstructures for Manipulation of Fluids in Microfluidics

Integrated Optofluidic Micro-Pumps in Micro-Channels with Uniform Excitation of a Polarization Rotating Beam.

Microfluidic Channels Fabrication Based on Underwater Superpolymphobic Microgrooves Produced by Femtosecond Laser Direct Writing