Abstract:Microstructured optical fibers (MOFs) have been widely utilized for optofluidic waveguides, in which the micro-holes along the MOFs act as microfluidic channels for various applications such as supercontiuum sources and aqueous solution sensors. The air hole diameter of MOFs is generally several microns to tens of microns, which is much smaller compared with traditional fluid-core fiber waveguide. However, for specific applications such as ultra-trace analysis and low-threshold fluidic lasers, this channel dimension is still relatively large. The slot waveguide could confine light in a subwavelength-scale channel, however, the short propagation length and high loss of the waveguide may limit its applications. Here we propose an approach to achieve low-loss subwavelength-scale optofluidic waveguide in MOFs. As shown in Fig. 1(a), the hollow-core of the MOF is tapered down to a subwavelength-scale, and then the MOF is selectively infiltrated with aqueous solution. So light could be confined in an aqueous core surrounded by a tapered air-silica cladding. As the refractive index of the cladding is close to that of air, the index contrast between the fluidic core and the cladding is high enough to provide an efficient index-guiding in a subwavelength-scale core. The mode pattern of a fundamental mode in a tapered aqueous core MOF is calculated when the core diameter is 600nm (Fig. 1(b)). As shown in Fig. 1(c), we compare our tapered air-silica cladding with Teflon cladding. At the wavelength of 633 nm, the light with the fraction of power over 65% could be guided in the aqueous core with the size of 600 nm, which is 4 times higher than that in a core surrounded by a Teflon cladding, which has an overlap fraction of only 15.7%. So the method we propose has obvious advantages over the traditional method using Teflon material. It provides a novel platform for low-loss subwavelength-scale fluid-core guiding with the long interaction length, and therefore have various potential applications.

Optofluidic Microchannels in Aerogel

High-Q, Low-Mode-volume Microsphere-Integrated Fabry–Perot Cavity for Optofluidic Lasing Applications

Subwavelength-diameter Silica Wires for Microscale Optical Components

High Index Contrast Subwavelength-Scale Optofluidic Waveguide in Mofs

Low-loss optofluidic waveguides in fused silica enabled by spatially shaped femtosecond laser assisted etching combined with carbon dioxide laser irradiation

Silica Aerogel in Microfluidic Channels: Synthesis, Chip Integration, Mechanical Reinforcement, and Characterization

Synthesis of silica aerogel films in liquid molds

Assembly of silica nanowires on silica aerogels for microphotonic devices.

Silica aerogel in optical fibre devices

Aerogel waveplates

Femtosecond Laser Engraved 2D Tunable Optofluidic Liquid Core/Air Cladding Channel Waveguides on PDMS

Aerogel-enhanced tapers and fibres

High-efficient Subwavelength-Scale Optofluidic Waveguides with Tapered Microstructured Optical Fibers

Optofluidics in Microstructured Optical Fibers

Aerogel-Lined Capillaries as Liquid-Core Waveguides for Raman Signal Gain of Aqueous Samples: Advanced Manufacturing and Performance Characterization

Transparent silica aerogel slabs synthesized from nanoparticle colloidal suspensions at near ambient conditions on omniphobic liquid substrates

Stable Low-Loss Optical Nanofibres Embedded in Hydrophobic Aerogel

Femtosecond laser micromachining of waveguides in silicone-based hydrogel polymers

Development of transparent silica aerogel over a wide range of densities

A Compact Optofluidic Cytometer with Integrated Liquid-Core/pdms-cladding Waveguides.

3D-nanoprinted on-chip antiresonant waveguide with hollow core and microgaps for integrated optofluidic spectroscopy