Abstract:In this paper, the main purpose was to investigate the effects of laser peening (LP) on the microstructural evolution and frictional wear resistance of TC6 titanium alloy. The surface topographic features, microhardness and residual stress distribution in the depth direction of differently treated specimens were measured using three-dimensional topography instrument, digital microhardness tester and residual stress instrument. The frictional wear test was carried out using a multifunctional friction wear tester. Meanwhile, X-ray diffraction (XRD), optical microscope (OM) and transmission electron microscopy (TEM) were utilized to investigate the effects of LP on the microstructural response of TC6 titanium alloy. The results indicated that the micro-pits induced by LP increased the surface roughness to a maximum of 6.94 μm. LP technique effectively improved the microhardness and frictional wear resistance of TC6 titanium alloy, and the wear form changed from abrasive wear, adhesive wear and fatigue spalling wear to abrasive wear at the laser energy of 8 J. Compared to the untreated specimens, the surface microhardness of the specimens treated by LP with 8 J increased from 356 HV to 442 HV, and the affected layer depth was approximately 500 μm. Moreover, the friction coefficient decreased from 1.2 to 0.5, the abrasion depth of the abrasion track was reduced by approximately 32 % compared to the untreated specimen. Additionally, the surface compressive residual stress induced by LP with 8 J reached about −510 MPa. The microstructural evolution of the specimens processed by LP was dominated by twin formation and dislocation slip, while the intercalation between multidirectional twins and the formation of sub-grain boundaries promoted grain refinement of TC6 titanium alloy. Refined grains, high density of dislocations, mechanical twins and the implantation of compressive residual stresses effectively improved the friction and wear resistance of TC6 titanium alloy.

The Effect of Laser Shock Peening on Surface Characteristics of Titanium Alloy

Studies on Laser Shock Peening on Nanomechanical and Mechano-Chemical Properties of Titanium Alloy (Ti6Al4V)

Microstructure evolution and mechanical properties of a lamellar near-α titanium alloy treated by laser shock peening

Molecular dynamics simulation of microstructural evolution and mechanical behavior of titanium alloy subjected to laser shock peening

Effects of Laser Shock Peening on Microstructure and Properties of Ti–6Al–4V Titanium Alloy Fabricated via Selective Laser Melting

Microstructural response and surface mechanical properties of TC6 titanium alloy subjected to laser peening with different laser energy

Formation Mechanism and Control Method of Residual Stress Profile by Laser Shock Peening in Thin Titanium Alloy Component

Laser Shock Peening of Ti6Al4V Alloy with Combined Nanosecond and Femtosecond Laser Pulses

Effect of laser shock peening without protective coating on surface integrity of titanium-based carbon-fibre/epoxy laminates

Mechanical properties and strengthening mechanisms of Ti-6Al-4V treated by electro-pulsing assisted laser shock peening

Laser shock processing of titanium alloys: a critical review on the microstructure evolution and enhanced engineering performance

Effect of TiN/Ti coating combined with laser shock peening pre-treatment on the fatigue strength of Ti-6Al-4V titanium alloy

Influence Of Laser Shock Peening On Low- And High-Cycle Fatigue Of An Ot4-0 Titanium Alloy

Surface residual stress, micro-hardness and geometry of TC6 titanium alloy thin-wall parts processed by multiple oblique laser shock peening

Effects of Ultrasonic Shot Peening on Fatigue Behavior of TA15 Titanium Alloy Fabricated by Laser Melting Deposition

The Influence of Absorbing Coating Material on the Efficiency of Laser Shock Peening

Laser shock peened Ti-6Al-4 V alloy: Experiments and modeling

Effects of laser shock peening on the hot corrosion behaviour of the selective laser melted Ti6Al4V titanium alloy

Experimental and Numerical Studies of Fatigue Behavior of Ti6Al4V Alloy Treated by Laser Shock Peening

Investigation on the deformation progress and residual stress of Ti-6Al-4V alloy during laser shock peening

Fabrication of TiN Coatings Deposited on Laser Shock Micro-Textured Substrates for Improving the Interface Adhesion Properties of Coatings