Abstract:The pipelined-SAR ADC has become popular in wide-bandwidth and high-resolution applications due to its power-efficient architecture [1]. In the pursuit of higher ADC speeds while maintaining precision and power efficiency, not only does the conversion time of the SAR sub-ADC need to be shortened, but also the speed and gain of residue amplifiers (RA) need to be enhanced. Conventional solutions to these two problems, including reducing the bit-cycling time of the SAR and increasing the RA bandwidth, often require extensive power costs, leading to a degraded power efficiency. To address the speed and gain challenges, three techniques are proposed in this work. First, a continuous-time SAR-assisted detect-and-skip (CTDAS) to parallelize the MSB conversion with ADC sampling, thus cutting down the $1^{\text{st}}$-stage sampling and conversion time by 35% when compared with a conventional detect-and-skip (DAS) technique. Second, an open-then-close correlated level shifting (OCCLS) technique applied in the residue amplifier, which significantly speeds up the first phase by open-loop amplification reusing the first two high-bandwidth stages of the RA. With the aid of a detect-and-cut loop, an optimal voltage gain in the first phase is obtained across PVT variations, thus realizing an >80dB equivalent RA open-loop gain $\left(\mathrm{A}_{\mathrm{EO}}\right)$ across PVT variations. Third, a hybrid static-floating ringamp architecture is implemented to improve the noise performance of the RA and to fit in well with the OCCLS scheme. Thanks to the techniques above, the 22nm prototype achieves 70.7dB SNDR under 200MS/s while consuming 2.0mW from a 0.9V supply. It measures a best energy efficiency of 177.7dB Schreier FoM with fs >150MS/s.

A 59.99dB SNDR 1.13mW Ping-pong NS SAR ADC for 3-D Transesophageal Echocardiography.

A 1.5 Mw 68 Db SNDR 80 Ms/s 2<formula Formulatype="inline"> <tex Notation="TeX">$\times$</tex></formula> Interleaved Pipelined SAR ADC in 28 Nm CMOS

A 1.54mW/Element 150μm-Pitch-Matched Receiver ASIC with Element-Level SAR/Shared-Single-Slope Hybrid ADCs for Miniature 3D Ultrasound Probes

A 0.91mw/element Pitch-Matched Front-End ASIC with Integrated Subarray Beamforming ADC for Miniature 3D Ultrasound Probes

A 14-b 20-MS/s 78.8 dB-SNDR Energy-Efficient SAR ADC With Background Mismatch Calibration and Noise-Reduction Techniques for Portable Medical Ultrasound Systems

Design of a 12-Bit 2 MS/s 12 Mw Pipelined SAR ADC in CMOS 0.18 Μm Technology for CZT-based Imaging System

Low-power Receive Electronics for a Miniature Real-Time 3D Ultrasound Probe

An Element-Matched Electromechanical ΔΣ ADC for Ultrasound Imaging.

A Pitch-Matched Front-End ASIC with Integrated Subarray Beamforming ADC for Miniature 3-D Ultrasound Probes

An Element-Matched Electromechanical $\delta\sigma$ ADC for Ultrasound Imaging

A 10-Ks/s 625-Hz-bandwidth 65-Db SNDR Second-Order Noise-Shaping SAR ADC for Biomedical Sensor Applications

9.1 A 2mW 70.7dB SNDR 200MS/s Pipelined-SAR ADC with Continuous-Time SAR-Assisted Detect-and-Skip and Open-then-Close Correlated Level Shifting.

An element-matched band-pass delta-sigma ADC for ultrasound imaging

A 3.07 Mw 30 MHz-BW 73.2 Db-Sndr Time- Interleaved Noise-Shaping SAR ADC with Self-Coupling Second-Order Error-Feedforward

A 73db SNDR 20ms/s 1.28mw SAR-TDC Using Hybrid Two-Step Quantization.

A 93.6-Db SNDR Fully Dynamic CT–DT Noise-Shaping SAR ADC with Closed-Loop Capacitively Coupled Two-Stage FIA

9.3 A 71dB SNDR 200MHz BW Interleaved Pipe-SAR ADC with a Shared Residue Integrating Amplifier Achieving 173dB FoMs.

An 871nw 96.2Db-Sndr Pipelined NS SAR ADC Achieving 180.8Db-Fomsndr with a Charge-Efficient CLS-Assisted Two-Stage FIA

A 10mw 10-ENOB 1gs/s Ring-Amp-Based Pipelined TI-SAR ADC with Split MDAC and Switched Reference Decoupling Capacitor.

A 10-Ks/s 625-Hz-bandwidth 60-Db SNDR Noise-Shaping ADC for Bio-potential Signals Detection Application

A 93.6Db-Sndr 5Khz-Bw Fully Dynamic Hybrid CT-DT Noise Shaping SAR ADC