Thermal Expansion and Defect Chemistry of MgO-Doped Sm2Zr2O7.

Qu Zhi,Chunlei Wan,Wei Pan

DOI: https://doi.org/10.1002/chin.200749008

2007-01-01

ChemInform

Abstract:ChemInform is a weekly Abstracting Service, delivering concise information at a glance that was extracted from about 200 leading journals. To access a ChemInform Abstract, please click on HTML or PDF.

What problem does this paper attempt to address?

Thermal Expansion and Defect Chemistry of MgO-Doped Sm2Zr2O7.

Zhixue Qu,Chunlei Wan,Wei Pan

DOI: https://doi.org/10.1021/cm071615z

IF: 10.508

2007-01-01

Chemistry of Materials

Abstract:A series of solid solutions of (Sm2-xMgx)Zr2O7-x/2 pyrochlores were prepared by a solid-state reaction and characterized by X-ray diffraction, high-temperature dilatometry, Raman spectroscopy, and X-ray photoelectron spectroscopy. X-ray diffraction and Raman spectroscopy reveal that MgO doping does not break down the pyrochlore structure Of Sm2Zr2O7 for all of the samples, though it increases the degree of structure disorder. However, the thermal expansion coefficient is remarkably increased through doping up to x = 0.075 with a maximum value around 11.94 x 10(-6) K-1 (room temperature to 1000 degrees C), which can mitigate the mismatches of thermal expansion in the high-temperature applications of SM2Zr2O7. A new solid-solution mechanism that is different from previous research was proposed and confirmed by analyzing the variation of the lattice parameters, experimental density, and X-ray photoelectron spectroscopy of samples. It involves the transformation of the solid-solution model about Mg2+ interstitial and substitution with a turning point at composition point x = 0.075. This transformation and consequently the variation of lattice energy may be responsible for the variation of the thermal expansion coefficient.
Thermal Expansion Coefficients of Sm2Zr2O7 Doped with MgO

Zhi Xue Qu,Wei Pan,Chun Lei Wan,Ye Xia Qin

DOI: https://doi.org/10.4028/www.scientific.net/KEM.336-338.2331

2007-01-01

Key Engineering Materials

Abstract:Thermal expansion coefficient (TEC) is one of the most concerned properties for thermal barrier coating (TBC) materials. To enhance thermal expansion coefficient, a series of rare-earth zirconates Sm2Zr2O7 with various contents of MgO were investigated. The samples were synthesized by solid state reaction at 1600 degrees C for 10h. And the thermal expansion coefficients of the samples were measured. The results showed that all the doping samples had higher expansion coefficients than pure Sm2Zr2O7. Moreover, compared with the data reported of 8YSZ, similar to 15% enhancement had been achieved above 300 degrees C.
Thermal expansion coefficients of Sm2Zr2O7 doped with MgO

Qu Zhixue,Pan Wei,Wan Chunlei,Qin Yexia

2007-01-01

Key Engineering Materials

Abstract:Thermal expansion coefficient (TEC) is one of the most concerned properties for thermal barrier coating (TBC) materials. To enhance thermal expansion coefficient, a series of rare-earth zirconates Sm2Zr 2O7 with various contents of MgO were investigated. The samples were synthesized by solid state reaction at 1600°C for 10h. And the thermal expansion coefficients of the samples were measured. The results showed that all the doping samples had higher expansion coefficients than pure Sm 2Zr2O7. Moreover, compared with the data reported of 8YSZ, ∼15% enhancement had been achieved above 300°C.
Effect of MgO Doping on the Thermal Conductivity of Sm2Zr2O7

Qu Zhixue,Wan Chunlei,Pan Wei

DOI: https://doi.org/10.3321/j.issn:1002-185x.2007.z2.191

2007-01-01

Rare Metal Materials and Engineering

Abstract:In order to reduce the thermal conductivity of rare-earth zirconates further, doping method was used to alter the concentration of defects in crystal, and effect of MgO doping on the thermal diffusivity and thermal conductivity of Sm2Zr2O7 was investigated. The samples were prepared by solid state reaction at 1600 degrees C for 10 h in air, and are all single phase with pyrochlore structure. Thermal conductivities of the samples were determined from the data of thermal diffusivity, specific heat capacity and density. The results have shown that the thermal conductivity does not decrease with increasing doping content of MgO as expected, but increase with a change of slope which turns up within the composition range of 0.075 similar to 0.100. It may be attributed to the solution mechanism of MgO and its variation.
Effect of Anti-Site Point Defects on the Mechanical and Thermodynamic Properties of MgZn2, MgCu2 Laves Phases: A First-Principle Study

Shuo Wang,Yuhong Zhao,Hua Hou,Zhiqin Wen,Peilin Zhang,Jianquan Liang

DOI: https://doi.org/10.1016/j.jssc.2018.04.001

IF: 3.3

2018-01-01

Journal of Solid State Chemistry

Abstract:A theoretical investigation on the effect of anti-site point defects on mechanical and thermodynamic properties of MgZn2 and MgCu2 based on the first-principles calculations has been implemented. The results show that Mg anti-site defect on Zn or Cu site plays a reinforcing role, while exhibiting a more brittle behavior. However, the defect phase of Cu anti-sites on Mg sublattice shows a ductile tendency. The temperature-dependent thermodynamic properties are also predicted along with Debye-Grüneisen model including Debye temperature, thermal expansion coefficient and vibrational heat capacity as well as vibrational entropy. Taking into account the contribution of the lattice vibration and thermal electronic excitations, the Helmholtz free energy F can be calculated, suggests that anti-site defects caused by the occupancy of Mg at the Zn or Cu site are thermodynamically unstable compared to the defect-free phases. In addition, the total amount of charge transfer, the overall and the local difference charge densities are further discussed to analyze the mechanism of mechanical properties.
Thermal Expansion and Thermal Conductivity of SmxZr1−xO2−x/2 (0.1 ≤ X ≤ 0.5) Ceramics

Zhan-Guo Liu,Jia-Hu Ouyang,Bai-He Wang,Yu Zhou,Jing Li

DOI: https://doi.org/10.1016/j.ceramint.2008.02.016

IF: 5.532

2009-01-01

Ceramics International

Abstract:A study was conducted of the effect of additions of samarium oxide on the thermal expansion and thermal conductivity of zirconium oxide for thermal barrier coatings. SmxZr1−xO2−x/2 (0.1≤x≤0.5) ceramic powders synthesized with a chemical-coprecipitation and calcination method were sintered at 1873K for 15h. Structures of the synthesized powders and sintered ceramics were identified by X-ray diffractometer. The morphologies of ceramic powders were observed by transmission electron microscope. The thermal expansion coefficients and thermal diffusion coefficients of SmxZr1−xO2−x/2 ceramics were studied with a high-temperature dilatometer and a laser flash diffusivity technique from room temperature to 1673K. The thermal conductivity was calculated from thermal diffusivity, density and specific heat of bulk ceramics. Sm0.1Zr0.9O1.95 ceramics consists of both monoclinic and tetragonal structures. However, Sm0.2Zr0.8O1.9 and Sm0.3Zr0.7O1.85 ceramics only exhibit a defect fluorite structure. Sm0.4Zr0.6O1.8 and Sm0.5Zr0.5O1.75 ceramics have a pyrochlore-type lattice. With the increase of Sm2O3 content, the linear thermal expansion of SmxZr1−xO2−x/2 ceramics increases except for Sm0.1Zr0.9O1.95. The thermal conductivities of SmxZr1−xO2−x/2 ceramics ranged from 1.41 at 873K to 1.86Wm−1K−1 at room temperature in a test temperature range of room temperature to 1673K, and the results can be explained by phonon scattering mechanism.
Microstructure and High Temperature Deformation Behavior of the Mo-ZrO 2 Alloys

Chaopeng Cui,Yimin Gao,Shizhong Wei,Guoshang Zhang,Yucheng Zhou,Xiangwei Zhu

DOI: https://doi.org/10.1016/j.jallcom.2017.05.013

IF: 6.2

2017-01-01

Journal of Alloys and Compounds

Abstract:The Mo-ZrO2 alloys were prepared by a hydrothermal synthesis and a powder metallurgy process. The grain size, density and hardness of the alloy sintered compacts were investigated. The deformation behavior of the alloy at high temperature was studied by using a Gleeble-1500D thermal simulated test machine. The strengthening effect of zirconia particles was found during the deformation process of the alloy at high temperature. The result shows the mechanical properties of the Mo-ZrO2 alloys were obviously improved due to the uniform distribution of the small second phase. After adding ZrO2, the hardness of the alloys has increased by 40%, and the high temperature strength of the alloy was increased. At the temperature of 1400 C-omicron, the strength of the alloys was increased by 35% compared with that of the pure molybdenum. The ZrO2 particles can effectively improve the deformation resistance, resulting in increase of the mechanical properties of the Mo-ZrO2 alloys. (C) 2017 Elsevier B.V. All rights reserved.
The manipulation of substitutional defects for realizing high thermoelectric performance in Mg3Sb2-based Zintl compounds

Juan Li,Fei Jia,Shuai Zhang,Shuqi Zheng,Boyi Wang,Liqiang Chen,Guiwu Lu,Liming Wu

DOI: https://doi.org/10.1039/c9ta06889a

IF: 11.9

2019-01-01

Journal of Materials Chemistry A

Abstract:By optimizing the concentration of the substitutional defect PrMg1, Mg3.2Pr0.02Sb1.5Bi0.5 exhibits a peak zT value of 1.70 at 725 K.
Composition‐dependent thermal and thermo‐mechanical properties of spinel‐type MgAlON from density functional calculation

Lu Ren,Hao Wang,Bingtian Tu,Pengyu Xu,Weimin Wang,Zhengyi Fu

DOI: https://doi.org/10.1111/jace.19377

IF: 4.186

2023-08-11

Journal of the American Ceramic Society

Abstract:Since ceramics based on MgAlON solid solutions are promising materials as refractories, windows/armors, phosphors, etc., it is essential to explore their thermal and thermo‐mechanical properties, owing to the physical requirements on application. In this study, Mg5xAl23−5xO27+5xN5−5x were chosen for the investigation on composition‐dependent thermal and thermo‐mechanical properties by the theoretical calculations. Though the binary system with octahedral bonds contributes more to the thermal expansion coefficient of Mg5xAl23‐5xO27+5xN5‐5x, the binary system with tetrahedral bonds plays an important role in the variation of the thermal expansion coefficient. The change of heat capacity with the rise of x is mainly attributed to the variation of covalent character of Mg5xAl23−5xO27+5xN5−5x. And the thermal conductivity is mainly affected by the scattering from atoms in 8a sites. Both thermal and mechanical properties contribute to the variation of thermo‐mechanical properties of Mg5xAl23−5xO27+5xN5−5x. This study can provide guidance to designing spinel materials with desirable thermal and thermo‐mechanical properties for application. This article is protected by copyright. All rights reserved

materials science, ceramics
The Thermal Properties of Al–Mg–TM (tm=sc, Zr): Ab Initio Study

Bi-Yu Tang,Dong-Lin Li,Ping Chen,Jian-Xiong Yi,Li Wen,Li-Ming Peng,Wen-Jiang Ding

DOI: https://doi.org/10.1016/j.solidstatesciences.2010.02.006

IF: 3.752

2010-01-01

Solid State Sciences

Abstract:Ab initio density functional theory (OFT) and density function perturbation theory (DEPT) have been used to investigate the thermal properties of the Al-Mg-Sc, Al-Mg-Zr and Al-Mg-Sc-Zr alloys over a wide range of temperature and pressure. Phonon dispersions are obtained at equilibrium and strained configurations by DEPT. Using the quasiharmonic approximation (QHA) for the free energy, several physical quantities of interest such as thermal Gruneisen parameter, heat capacity at constant pressure and at constant volume, thermal expansion coefficient, entropy, adiabatic bulk modulus and isothermal bulk modulus as a function of temperature and pressure are calculated and discussed. The present results show that the thermal expansion coefficient of the Al-Mg-Sc-Zr is far lower than that of Al-Mg-Sc and Al-Mg-Zr, and the variation features in the adiabatic bulk modulus and isothermal bulk modulus for the Al-Mg-Sc-Zr are also very different from that of Al-Mg-Sc and Al-Mg-Zr. (C) 2010 Elsevier Masson SAS. All rights reserved.
Impact of Isovalent and Aliovalent Substitution on the Mechanical and Thermal Properties of Gd2Zr2O7

S. Zhang,H. B. Zhang,F. A. Zhao,M. Jiang,H. Y. Xiao,Z. J. Liu,X. T. Zu

DOI: https://doi.org/10.1038/s41598-017-06725-8

IF: 4.6

2017-01-01

Scientific Reports

Abstract:In this study, a density functional theory method is employed to investigate the effects of isovalent and aliovalent substitution of Sm 3+ on the phase stability, thermo-physical properties and electronic structure of Gd 2 Zr 2 O 7 . It is shown that the isovalent substitution of Sm 3+ for Gd 3+ results in the formation of Gd 2 Zr 2 O 7 -Sm 2 Zr 2 O 7 solid solution, which retains the pyrochlore structure and has slight effects on the elastic moduli, ductility, Debye temperature and band gap of Gd 2 Zr 2 O 7 . As for the aliovalent substitution of Sm 3+ for Zr 4+ site, a pyrochlore-to-defect fluorite structural transition is induced, and the mechanical, thermal properties and electronic structures are influenced significantly. As compared with the Gd 2 Zr 2 O 7 , the resulted Gd 2 Sm y Zr 2-y O 7 compositions have much smaller elastic moduli, better ductility and smaller Debye temperature. Especially, an amount of electrons distribute on the fermi level and they are expected to have larger thermal conductivity than Gd 2 Zr 2 O 7 . This study suggests an alternative way to engineer the thermo-physical properties of Gd 2 Zr 2 O 7 and will be beneficial for its applications under stress and high temperature.
Deformation Mechanisms in High-Efficiency Thermoelectric Layered Zintl Compounds

Guodong Li,Umut Aydemir,Max Wood,Qi An,William A. Goddard,Pengcheng Zhai,Qingjie Zhang,G. Jeffrey Snyder

DOI: https://doi.org/10.1039/c7ta02080e

IF: 11.9

2017-01-01

Journal of Materials Chemistry A

Abstract:We use DFT to determine the deformation mechanism of Mg3Sb2, and propose a substitution strategy to enhance its mechanical strength.
Hot deformation behavior and microstructure evolution of Mg-Gd-Y (-Sm)-Zr alloys

Hao Pang,Quanan Li,Xiaoya Chen,Peijun Chen,Xiangyu Li,Jinfeng Tan

DOI: https://doi.org/10.1016/j.jallcom.2022.165937

IF: 6.2

2022-01-01

Journal of Alloys and Compounds

Abstract:We investigated the deformation behavior of Mg-Gd-Y(-Sm)-Zr alloys during high-temperature uniaxial compression (T = 350 degrees C, 400 degrees C, 450 degrees C and 500 degrees C; =0.003 s-1, 0.01 s-1, 0.1 s-1 and 1 s-1). The dynamic recrystallization (DRX) critical strain of Mg-Gd-Y(-Sm)-Zr was calculated, and its accuracy was verified by the transmission electron microscope (TEM). The hot deformation activation energy and constitutive equation after hot compression were calculated. The effect mechanism of Sm on microstructure evolution was also analyzed by the electron backscatter diffraction (EBSD) and TEM. It can be concluded that the hot deformation activation energies of Mg-Gd-Y-Zr and Mg-Gd-Y-Sm-Zr were 206.17 kJ/mol and 263.07 kJ/mol, respectively. The addition of Sm can increase flow stress and make DRX occur earlier. With the increase of strain, Sm delayed the DRX by inhibiting the activity of pyramidal < c+a > slip. Under the deformation condition of 400 degrees C/0.003 s-1/0.7, the continuous dynamic recrystallization (CDRX) mechanism was domi-nant in Mg-Gd-Y-Zr and Mg-Gd-Y-Sm-Zr. In addition, the dynamic precipitation phase after adding Sm was the ss-Mg5(Gd, Y, Sm) equilibrium phase with a face-centered cubic structure. There was a staggered chain distribution between DRX grains and precipitates at the original deformation grain boundary, which effectively hinders dislocation rearrangement and grain boundary migration. Finally, we constructed the DRX mechanism diagram and the interaction diagram between the precipitated phase and DRX grains.' (c) 2022 Elsevier B.V. All rights reserved.
The Effect of Gd and Zn Additions on Microstructures and Mechanical Properties of Mg-4sm-3nd-Zr Alloy

Chaojie Che,Liren Cheng,Libo Tong,Zhongyi Cai,Hongjie Zhang

DOI: https://doi.org/10.1016/j.jallcom.2017.02.269

IF: 6.2

2017-01-01

Journal of Alloys and Compounds

Abstract:The effect of gadolinium (Gd, 1 wt%) and zinc (Zn, 1 wt%) additions on microstructures and mechanical properties of Mg-4Sm-3Nd-Zr alloy have been investigated by optical microscopy, scanning electron microscopy, X-ray diffraction and transmission electron microscopy. The additions of Gd and Zn changed the kinds of precipitates in the T6-state alloy, leading to improvement of tensile properties. The prismatic precipitated phases beta' and beta" existed in the peak-aged Mg-4Sm-3Nd-Zr alloy, while beta' phase and gamma phase were dominant precipitates in peak-aged Mg-4Sm-3Nd-Gd-Zn-Zr alloy, and the strip-shaped ZrZn phase could also be observed after solution treatment at 798 K for 8 h. The peak-aged Mg-4Sm-3Nd-Gd-Zn-Zr alloy exhibited good heat resistance with ultimate tensile properties 213 MPa and elongation 8.6% at 573 K, which was attributed to beta' phase, g phase and ZrZn phase hindering dislocation and grain boundary motions. (C) 2017 Elsevier B. V. All rights reserved.
Hot Deformation Behavior and Dynamic Precipitation Characteristics of Mg-Gd-Nd(-Sm)-Zr Alloys

Ziyi Chen,Qian Zhang,Quanan Li,Hongxi Zhu,Xiaoya Chen,Xiangyu Li,Peijun Chen,Jian Bao

DOI: https://doi.org/10.1016/j.jmrt.2021.11.031

IF: 6.267

2021-01-01

Journal of Materials Research and Technology

Abstract:We deeply analyze the deformation behavior of Mg-Gd-Nd(-Sm)-Zr alloys under high temperature uniaxial compression, and explore the influence mechanism of Sm on the microstructure evolution of Mg-Gd-Nd-Zr alloy. We can draw the following conclusions: the addition of Sm delays the dynamic recrystallization of Mg-Gd-Nd-Zr alloy, resulting in the increase of stress and the decrease of machinability. There is no dynamic precipitation in Mg-Gd-Nd-Zr alloy at 400 °C/0.01 s−1/0.7, which is related to the high solute-vacancy binding energy of Nd. Under the same deformation condition, two kinds of dynamic precipitates with different size and shape appear in Mg-Gd-Nd-Sm-Zr alloy: fine particle phase and coarse lamellar phase. The two precipitates are Mg(Gd, Nd, Sm) with body-centered cubic structure, and are incoherent with the matrix. The coarse lamellar phase effectively hinders dislocation rearrangement, which explains the delay of dynamic recrystallization.
Microstructure Evolution and Mechanical Properties of Mg-Gd-Sm-Zr Alloys

Ningyuan Liu,Zhenyan Zhang,Liming Peng,Wenjiang Ding

DOI: https://doi.org/10.1016/j.msea.2014.12.114

IF: 6.044

2015-01-01

Materials Science and Engineering A

Abstract:The microstructure evolution and mechanical properties of Mg-Gd-Sm-Zr alloys during heat treatment were systematically investigated. The precipitation sequence of an α-Mg supersaturated solid solution (S.S.S.S., cph) during aging at 225°C is: S.S.S.S.→β″ (D019)→β′ (cbco)→β1 (fcc)→β (fcc), which is different from previously reported Mg-Gd-Sm systems. The observed shortened incubation periods in the Mg-Gd-Sm-Zr alloys can be mainly attributed to the increased amount of Sm present. Peak-aged Mg-Gd-Sm-Zr alloys exhibit mechanical properties superior to that of the WE54 alloy. The product of strength and elongation (PSE) was used to estimate the toughness of Mg-Gd-Sm-Zr alloys, and the PSE value decreases with increasing RE content.
Structural Evolution and Thermophysical Properties of (smxgd1−x)2zr2o7 (0≤x≤1.0) Ceramics

Zhan-Guo Liu,Jia-Hu Ouyang,Yu Zhou

DOI: https://doi.org/10.1016/j.jallcom.2008.04.042

IF: 6.2

2009-01-01

Journal of Alloys and Compounds

Abstract:Structural evolution and thermophysical properties of (SmxGd1−x)2Zr2O7 (0≤x≤1.0) were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, high-temperature dilatometer and laser flash diffusivity measurements from room temperature to 1400°C. Pure Gd2Zr2O7 ceramics exhibit a defective fluorite-type structure, however, (SmxGd1−x)2Zr2O7 (0.1≤x≤1.0) ceramics are with a pyrochlore-type structure. The linear thermal expansion coefficients of (SmxGd1−x)2Zr2O7 ceramics increase with increasing test temperature. The thermal diffusivities of (SmxGd1−x)2Zr2O7 ceramics range from 0.390 to 0.770mm2s−1, while the thermal conductivities of (SmxGd1−x)2Zr2O7 ceramics are located within the range of 1.20 to 1.99Wm−1K−1 from room temperature to 1400°C.
Deformation Behavior, Microstructure Evolution and Hot Workability of Mg-3.7Gd-2.9Y-0.7Zn-0.7Zr Alloy

Xueze Jin,Wenchen Xu,Debin Shan,Chang Liu,Qi Zhang

DOI: https://doi.org/10.1007/s12540-017-6352-2

IF: 3.451

2017-01-01

Metals and Materials International

Abstract:The deformation behavior of Mg-3.7Gd-2.9Y-0.7Zn-0.7Zr magnesium alloy has been investigated by thermal compression test conducted on a Gleeble-1500D thermal simulator in the temperature range of 375-475 °C and strain rate range of 0.001-1 s-1. It indicates that the addition of RE, the introduction of LPSO phases and the segregation of Zr element near the grain boundaries contributed to the high activate energy (Q = 354.08 kJ/mol) of the present Mg alloy. The long period stacking ordered (LPSO) phase could not only strengthen the alloy and contribute to the nucleation of dynamic recrystallization, but also re-precipitate in the recrystallization grains. The processing map based on MDMM and Murty’s instability criterion was more precise than the one based on DMM and Prasad’s instability criterion. The processing map exhibited two workable regions with sufficient dynamic recrystallization: 415-435 °C, 0.001-0.006 s-1 and 435-475 °C, 0.01-1 s-1. The flow instability was prone to occur at low temperature and high strain rate associated with the appearance of bands of flow localization and cracking.
Effect of Point Defects on the Thermal Conductivity of Sc2O3-Y2O3 Co-Stabilized Tetragonal ZrO2 Ceramic Materials

W. Fan,Y. Bai,Z. Z. Wang,J. W. Che,Y. Wang,W. Z. Tao,R. J. Wang,G. Y. Liang

DOI: https://doi.org/10.1016/j.jeurceramsoc.2019.02.034

IF: 5.7

2019-01-01

Journal of the European Ceramic Society

Abstract:In this paper, the reduction mechanism in thermal conductivity of a series of Sc2O3-Y2O3 co-stabilized tetragonal ZrO2 ceramics is systematically discussed. The thermal conductivity is approximately 20-28% lower than that of 6-8 wt.% yttria-stabilized zirconia (YSZ). A phonon scattering model, on account of the influence of oxygen vacancy variation and cation mass fluctuation, is optimized and utilized to depict the thermal conductivity of these materials. For the samples with the same amount of oxygen vacancy, Sc3+ is more effective in lowering thermal conductivity than y(3) due to the large mass difference with Zr4+, as evidenced by the scattering model and phonon vibrational density of states. The experimental and calculation results suggest that this optimized model is proved to be more effective in predicting the thermal conductivity of binary or multiple rare earth oxides co-doped tetragonal ZrO2 and guiding the compositional design of thermal barrier materials.
Phase Composition, Crystal Structures and Enhanced Microwave Dielectric Properties of Mg2+/Zr4+ Co-Doped Al2Mo3O12 Ceramics

Lifeng Ding,Ben Heng,Dawei Wang,Haikui Zhu,Lixi Wang,Yi Hou,Zhenxiao Fu,Qitu Zhang

DOI: https://doi.org/10.1016/j.jallcom.2024.174918

IF: 6.2

2024-01-01

Journal of Alloys and Compounds

Abstract:In this work, the substitution of Al3+ by Zr/Mg in Al2Mo3O12 was designed to enhance the quality factor while simultaneously adjusting the thermal stability of the resonant frequency. The Al2-2x(Zr0.5Mg0.5)2xMo3O12 (AMZM) (0.1 ≤ x ≤ 0.5) ceramics were synthesized using a simple solid-state method, resulting in all components exhibiting single-phase crystallinity and a dense structure. A phase transition temperature below room temperature was observed when x ≥ 0.4. Furthermore, the quality factor of the synthesized samples, compared to pure-phase Al2Mo3O12 (εr = 6.79, Q×f = 28471GHz, τf = -48.77 ppm/℃), increased by nearly threefold. A detailed investigation of the crystal structure of the samples was conducted through Rietveld refinement. The composition with x = 0.3 (monoclinic phase) exhibited optimal dielectric performance after sintering at 800 ℃ for 6h: εr = 7.84, Q×f = 86511GHz, τf = -42.08 ppm/℃. By forming a composite ceramic with (Li1/2Sm1/2)MoO4, the negative τf value was further adjusted to near zero.

Thermal Expansion and Defect Chemistry of MgO-Doped Sm2Zr2O7.

Thermal Expansion and Defect Chemistry of MgO-Doped Sm2Zr2O7.

Thermal Expansion Coefficients of Sm<sub>2</sub>Zr<sub>2</sub>O<sub>7</sub> Doped with MgO

Thermal expansion coefficients of Sm2Zr2O7 doped with MgO

Effect of MgO Doping on the Thermal Conductivity of Sm2Zr2O7

Effect of Anti-Site Point Defects on the Mechanical and Thermodynamic Properties of MgZn2, MgCu2 Laves Phases: A First-Principle Study

Thermal Expansion and Thermal Conductivity of SmxZr1−xO2−x/2 (0.1 ≤ X ≤ 0.5) Ceramics

Microstructure and High Temperature Deformation Behavior of the Mo-ZrO 2 Alloys

The manipulation of substitutional defects for realizing high thermoelectric performance in Mg<sub>3</sub>Sb<sub>2</sub>-based Zintl compounds

Composition‐dependent thermal and thermo‐mechanical properties of spinel‐type MgAlON from density functional calculation

The Thermal Properties of Al–Mg–TM (tm=sc, Zr): Ab Initio Study

Impact of Isovalent and Aliovalent Substitution on the Mechanical and Thermal Properties of Gd2Zr2O7

Deformation Mechanisms in High-Efficiency Thermoelectric Layered Zintl Compounds

Hot deformation behavior and microstructure evolution of Mg-Gd-Y (-Sm)-Zr alloys

The Effect of Gd and Zn Additions on Microstructures and Mechanical Properties of Mg-4sm-3nd-Zr Alloy

Hot Deformation Behavior and Dynamic Precipitation Characteristics of Mg-Gd-Nd(-Sm)-Zr Alloys

Microstructure Evolution and Mechanical Properties of Mg-Gd-Sm-Zr Alloys

Structural Evolution and Thermophysical Properties of (smxgd1−x)2zr2o7 (0≤x≤1.0) Ceramics

Deformation Behavior, Microstructure Evolution and Hot Workability of Mg-3.7Gd-2.9Y-0.7Zn-0.7Zr Alloy

Effect of Point Defects on the Thermal Conductivity of Sc2O3-Y2O3 Co-Stabilized Tetragonal ZrO2 Ceramic Materials

Phase Composition, Crystal Structures and Enhanced Microwave Dielectric Properties of Mg2+/Zr4+ Co-Doped Al2Mo3O12 Ceramics