Abstract:Background: The Accelerator Driven Subcritical System (ADS) uses a proton beam incident on a target to produce neutrons used in a nuclear reactor to process spent fuel in two ways: to accelerate its decomposition into non-radioactive waste, and to increase the rate at which it is recycled into nuclear fuel. Two cryomodules, each consisting of 7 superconducting spoke cavities, 7 superconducting magnets and 7 beam position monitors, are used to accelerate the proton beams from 3.2 MeV to 10 MeV. The superconducting magnet contains a solenoid for beam focusing and two correctors for orbit correction, it is a key component for ADS injection. Purpose: This study aims at a short superconducting magnet design to meet the required integral field strength and to reduce the leakage field at the nearby superconducting spoke cavities. The design current for the solenoid is 210 A. Methods: The main solenoid and two bucking solenoids plus the iron yoke were used to meet the leakage field requirements which is less than 1 G at a distance of 270 mm from the solenoid center. In order to shorten the magnet length to 170 mm, special design methods were taken for the magnet cryostat by removing two conflicts flanges and replacing them with the direct Al ring seal methods. A kind of conducted the current leads similar as that of Large Hadron Collider (LHC) corrector magnets was applied to the 2.1-K, 3 100-Pa cryogenic system. The small store energy magnet led to the introduction of active quench detected system, which is much more reliable. Two short magnets and two spoke cavities were installed inside a test cryomodule to test the online operation properties of the SC magnet and the SC spoke cavity. Results: A quench performance in the vertical test shows that the operating current of the solenoid magnet can reach above 300 A after natural quenching on three occasions during current ramping (260 A, 268 A and 308 A). Online operating test shows that two magnets can work at 4.2 K and 2.1 K, respectively. The quench protection system worked well when two quenches occurred as the liquid helium level decreased. Conclusion: The online operation for the two magnets confirms the physical and the mechanical design, the reliability of the quench detection technique.

Design, Fabrication and Performance Test of SHINE Superconducting Quadrupole Magnets

Cryogenic Tests of SHINE Superconducting Quadrupole Magnets in the Multifunction Test Facility

Cooling Design for the Magnetic Structure of SHINE Superconducting Undulator

Design and Optimization of Combined-Function Quadrupole-Sextupole Magnets

Magnetic Field Measurement, Shimming and Processing for 230 MeV Superconducting Cyclotron Main Magnet

Development of a Novel High Gradient Quadrupole Magnet

Design and testing of focusing magnets for a compact electron linac

Design of the Magnets of the HALS Project

Design and Test of A Short Mockup Magnet for the Superconducting Undulator at the Ssrf

The Magnet Design of the Ssrf Storage Ring and Booster

High-precision positioning of Hall probes for SCU magnetic field measurement

Design and Test of Power Supply System for 45 T Hybrid Magnet Superconducting Outsert at the CHMFL

Design and Test of Superconducting Magnet for 200 MeV Proton Cyclotron

Electromagnetic and Mechanical Analysis of DC Magnet for Super X Test Facility

Cryogenic calibration for Hall probes

Design and Fabrication of a Cross-Warm-Bore Split-Gap Superconducting Magnet System

Research on the method of magnetic field shimming for SC200 superconducting cyclotron

Fabrication and cold test of prototype of spatially periodic radio frequency quadrupole focusing linac

Preliminary Study On Measurement Of Magnetic Center Of Quadrupoles Using Quadrupole Shunt For Hefei Storage Ring

Mechanical Design of the Half-length Prototype for a Superconducting FECR Ion Source

Development and Testing of the Short Superconducting Magnets for ADS Injection I