Abstract:Background: The Accelerator Driven Subcritical System (ADS) uses a proton beam incident on a target to produce neutrons used in a nuclear reactor to process spent fuel in two ways: to accelerate its decomposition into non-radioactive waste, and to increase the rate at which it is recycled into nuclear fuel. Two cryomodules, each consisting of 7 superconducting spoke cavities, 7 superconducting magnets and 7 beam position monitors, are used to accelerate the proton beams from 3.2 MeV to 10 MeV. The superconducting magnet contains a solenoid for beam focusing and two correctors for orbit correction, it is a key component for ADS injection. Purpose: This study aims at a short superconducting magnet design to meet the required integral field strength and to reduce the leakage field at the nearby superconducting spoke cavities. The design current for the solenoid is 210 A. Methods: The main solenoid and two bucking solenoids plus the iron yoke were used to meet the leakage field requirements which is less than 1 G at a distance of 270 mm from the solenoid center. In order to shorten the magnet length to 170 mm, special design methods were taken for the magnet cryostat by removing two conflicts flanges and replacing them with the direct Al ring seal methods. A kind of conducted the current leads similar as that of Large Hadron Collider (LHC) corrector magnets was applied to the 2.1-K, 3 100-Pa cryogenic system. The small store energy magnet led to the introduction of active quench detected system, which is much more reliable. Two short magnets and two spoke cavities were installed inside a test cryomodule to test the online operation properties of the SC magnet and the SC spoke cavity. Results: A quench performance in the vertical test shows that the operating current of the solenoid magnet can reach above 300 A after natural quenching on three occasions during current ramping (260 A, 268 A and 308 A). Online operating test shows that two magnets can work at 4.2 K and 2.1 K, respectively. The quench protection system worked well when two quenches occurred as the liquid helium level decreased. Conclusion: The online operation for the two magnets confirms the physical and the mechanical design, the reliability of the quench detection technique.

Development and Testing of the Short Superconducting Magnets for ADS Injection I

The Superconducting Magnet for ADS Injection-I

Magnetic Field and Strain Measurements of A Superconducting Solenoid Magnet for C-Ads Injector-Ii During Excitation and Quench Test

Quench Analysis and Experiments on Nb3Sn Superconducting Magnet Half-Length Prototype

Field measurement for superconducting magnets of ADS injector I

Commissioning, Performance, and Effect of the Quench Current-boosting Device on a Dedicated Superconducting Magnet

A Compact Superconducting Solenoid for China-ADS Injector II

Engineering Design of 1 MJ HTS SMES System with Ka-Level Current Capacity for NICA Accelerator

Development of A Superconducting Solenoid for Cads

Design and Test of A Short Mockup Magnet for the Superconducting Undulator at the Ssrf

Design and Test of Superconducting Magnet for 200 MeV Proton Cyclotron

Quench Safety Simulation and Verification of Superconducting Coils for the SC200 Superconducting Cyclotron

Superconducting Feeder System For Iter Central Solenoid Module Final Test Facility

Mechanical Design of a Nb3Sn Superconducting Magnet System for a 45 GHz ECR Ion Source

Development of a 1/2-length prototype high field Nb3Sn magnet for the 4th generation ECR ion source

Development of A Superconducting Magnet System for Microwave Application

Mechanical Design of the Half-length Prototype for a Superconducting FECR Ion Source

Preliminary Design of DC Magnet for Super-X Test Facility

Design and thermal performance of spoke cavity prototype cryomodule of the Chinese Accelerator Driven Sub-critical system Injector-I

Full Period Superconducting Section Physics Design for Injector Ii of China-Ads

Quench Protection Design and Simulation of a 7 Tesla Superconducting Magnet