Abstract:Shanghai Soft-Xray FEL (SXFEL) test facility was designed and built to demonstrate EEHG and HGHG schemes and verify key technologies for the future hard xray FEL facility (SHINE). After three years commissioning 8.8 nm FEL radiation with peak power of 1 MW had been achieved at the end of 2019. The design, fabrication, commissioning and operation of BI system including striplineBPM, Cavity-BPM, screen monitor, bunch length monitor, beam arrival monitor, bunch energy monitor, will be introduced in this paper. Several lessons learned during design stage and beam commissioning stage, such as radiation damage of CCDs and step-motors, bad choice of CBPM working frequency, thermal drift of BAM and so on, will be addressed as well. INTRODUCTION SXFEL Test Facility (SXFEL-TF) was initiated in 2006 and founded in 2014. Its 0.84GeV linac and undulators were installed through 2016 to 2018, it is for testing the cascaded seeding schemes. The main parameters are listed in Table 1. The SXFEL-TF commissioning has completed this year, and the SXFEL user facility (SXFEL-UF) is under construction. The layout of SXFEL-TF and SXFEL-UF are shown in Figure 1. Table 1: SXFEL-TF Parameters Parameter Value Total length 293m Electron energy 0.84 GeV Bunch charge 0.5 nC Repetition rate 10 Hz FEL output 8.8 nm FEL scheme HGHG/EEHG FEL pulse 100-200 fs FEL power >100 MW Figure 1: Layout of SXFEL-TF (top) and SXFEL-UF (bottom). In order to maintain high FEL gain, high performance beam instrumentation system is required for the SXFELTF. Measured beam parameters including bunch charge, beam position (BPM), beam profile, beam arrival time (BAM) and bunch length (BLM). Table 2 lists the beam diagnostic devices included and the required resolution. Table 2: Requirements of SXFEL-TF Diagnostic System

Cryogenic Tests of SHINE Superconducting Quadrupole Magnets in the Multifunction Test Facility

Beam instrumentation system for shanghai soft x-ray fel test facility*

Operation of cryogenic system at 2 K for the SHINE test facility

Development of a Conduction-Cooled HTS SMES

Prototype design of wire scanner for shine*

Cryogenic calibration for Hall probes

Dynamic Simulation of Warm Compressor Station for SHINE Test Facility Cryoplant

Development and tests of the 499.8 MHz srf cryomodules for HEPS

High RF power tests of the first 1.3 GHz fundamental power coupler prototypes for the SHINE project

Performance of the 2 × 4-Cell Superconducting Linac Module for the THz-FEL Facility

Cryogenic and safety design of the future high field cable test facility at Fermilab

The 5.8 T Cryogen-Free Gyrotron Superconducting Magnet System on HL-2A

High Q and high gradient performance of the first medium-temperature baking 1.3 GHz cryomodule

Quench Safety Simulation and Verification of Superconducting Coils for the SC200 Superconducting Cyclotron

Stable Acceleration of a LHe-Free Nb3Sn demo SRF e-linac Based on Conduction Cooling

Cryogenic Distribution System Design for Cryomodules and Cavities Test in HIAF Project

Cryogenic System for the Cryomodule Test Stand at Fermilab

The MING proposal at SHINE: megahertz cavity enhanced X-ray generation

Structural Design of DC Magnet for Super-X Test Facility

Design and Test of A Short Mockup Magnet for the Superconducting Undulator at the Ssrf

Medium-temperature furnace baking of 1.3 GHz 9-cell superconducting cavities at IHEP