Approach on Relationship Between Drawing in Back Area and Slippage of Aprons

Ming Dong

2002-01-01

Abstract:Through analysis of slipping condition of aprons and drawing theory for spinning draw area,the conclusion is made that irregulation of yarn movement in drawing area is much related to the yarn quality.In practice,something must be done against slippage of aprons.

What problem does this paper attempt to address?

Approach into Relationship Between Drawing in Back Area and Slippage of Aprons

Mingfei Zhou

2002-01-01

Abstract:Through analysis of slipping condition of aprons and drawing theory for spinning draw area,conclusion is made that irregulation of yarn movement in draw area is much related to the yarn quality.In practice,something must be done against slippage of aprons.
The Optimization of the Key Components of the Spinning Machine Conveyor System Based on ISIGHT

Bin Lin,Xu Zhang,Xiaogang Liu

DOI: https://doi.org/10.4028/www.scientific.net/amr.627.466

2012-01-01

Advanced Materials Research

Abstract:A transfer system in roving-spinning unit that establishes a connection between spindles of roving frame and spinning frame achieves the manipulations automatically in spinning workshop. We study that ISIGHT drive ANSYS to conduct integrated optimization of the key conveyor system components in this paper, the ANSYS-ISIGHT integration is successful. Before the optimal design, using the Latin method to design experiments. The experimental design can show the degree that the state variables and the target variables are affected by each input factor. The factor that has little impact on the results can be removed, thus the efficiency of the optimization can be improved. After the experimental design, using the multi-objective neural network to optimize the beam. Giving the beam safety conditions, including intensity, toughness, modal, stability. We optimize the structure base on security conditions, the volume of the beam in roving and yarn reservoir area has been largely decreased. Achieving the objectives of the lightweight design.
The influence of the friction field on accelerating position distribution

Jule Fan,Jiang Wang,Yuze Zhang,Jun Wang

DOI: https://doi.org/10.1177/00405175241249195

IF: 2.3

2024-05-02

Textile Research Journal

Abstract:Textile Research Journal, Ahead of Print. In accordance with the tenets of displacement deviation theory, the distribution of accelerating positions was the main reason for the uneven output sliver. To elucidate this phenomenon, a dynamic drafting model with controllable fiber proportion was developed in this paper to simulate the accelerating process of the floating fiber. The model was employed to investigate the impact of the friction field on the distribution of accelerating positions, achieved through the manipulation of friction field distribution and fiber proportion in the drafting zone. The simulation results indicated that, with various drafting conditions, the friction field at the position with a higher slow fiber proportion always made the accelerating position distribution closer to the front roller. In addition, the duration of the friction field influence on the fiber floating process was found to be directly proportional to its effect on the accelerating position distribution. Furthermore, there was a critical slow fiber proportion, which increased in tandem with the augmentation of slow fiber proportions in the drafting zone. The friction field at the position where the proportion of slow fibers was higher than the critical slow fiber proportion made the accelerating position distribution closer to the front roller; otherwise, the friction field made the accelerating position distribution closer to the back roller. This study can offer a valuable reference for designing more effective friction field distribution to improve the output sliver quality.

materials science, textiles
The influence rule of uneven input sliver on floating fiber motion during the dynamic drafting process

Jule FanJiang WangYuze ZhangJun Wanga Donghua University,Shanghai,Chinab Key Laboratory of Textile Science and Technology of the Ministry of Education,Donghua University,Shanghai,China

DOI: https://doi.org/10.1080/00405000.2024.2351784

IF: 1.7698

2024-05-11

Journal of the Textile Institute

Abstract:This paper established a dynamic drafting model with the frictional force between fibers to simulate the drafting process of the uneven input sliver. The simulated results indicated that the number of back, slow-floating, fast-floating, and front fibers would change sequentially when the input sliver linear density changed. Due to the different timing of quantity changes in the four types of fibers, the uneven input sliver led to a repeated increase and decrease in the proportion of fast and slow fibers in the drafting zone. When the input sliver linear density decreased, the floating fibers first continuously accelerated earlier, then accelerated earlier later, and then continuously accelerated earlier again. The effect of increasing the input sliver linear density on the floating fiber motion was opposite to that of decreasing the input sliver linear density. This paper offers a theoretical foundation for further improving the auto-leveling approach.

materials science, textiles
Analysis of Flowing Characteristics of Abrasive Flow Machining in Slit

Zhiguo Dong,Xiaodong Zhang,Yuanzong Li

DOI: https://doi.org/10.4028/www.scientific.net/kem.467-469.283

2011-01-01

Key Engineering Materials

Abstract:Based on the equations of motion and rheological theory of abrasive flow in the slit, effect between wall slip and grinding has been analyzed and grinding flow model of abrasive flow has been built in this paper. Wall pressure, wall shear stress, wall slip and the grinding force equation of abrasive flow were derived using the model. What is important, the effects of relevant factors were analyzed. The results show that wall slip is one of the necessary conditions that in abrasive flow machining, and show that main factors influencing wall slip are viscosity coefficient , grinding coefficient of abrasive flow, and the first normal stress difference. In the meantime, the results also show that grinding force in slit wall is proportional to the entrance pressure of slit. That is to say that the grinding force of per unit length in flow direction increasing dramatically with decreasing slit height.
Approach into Reduction of Fuzzy Yarn of Winding Bobbin

Bo ZHAO

DOI: https://doi.org/10.3969/j.issn.1001-9634.2006.z2.016

2006-01-01

Abstract:As to the increase instead of decrease of fuzzy yarn after winding process,analysis is done to the factors involved with fuzzy yarn.Conclusion is made that fuzzy yarn in winding process is related with variety,performance and operation of winding machines.Winding machines 1332 and GA013 are advantageous over auto-winding machines in less fuzzy yarn.Fuzzy yarn must be be reduced from the bobbin yarn,and measures taken to properly select drag washers,devil catchers,yarn guiding,blow-up ring,balloon controller,balloon blower clearrance as to their specifications.And more,new backset nozzles,new blow-up rings and guiding wheels are indispensable.
The Ⅱ Kind of Size Effect on Micro Deep Drawing

MA Ning,DONG Xiang-huai

DOI: https://doi.org/10.3969/j.issn.1007-2012.2007.01.025

2007-01-01

Abstract:In this paper,the strain gradient hardening model proposed by other scholars has been analyzed and modified firstly.After that,we have analyzed the flange's stress of micro deep drawing,and deduced the moment with strain gradient effect on the onset of the flange wrinkling.Finally I have found out the change of strain gradient effect in the micro deep drawing.It provides the reference of estimating the anti-wrinkling ability of flange on process design of microforming with strain gradient effect.
Processing Practice of Rubber-covered Roll Forward Motion Draft in Spinning Frame

Xu Qingli,Ma Kun,Gao Jianmin

DOI: https://doi.org/10.3969/j.issn.1001-7415.2009.07.003

2009-01-01

Abstract:Processing of rubber-covered roll forward motion draft in spinning frame was discussed.The processing characteristics,finish yarn quality,modification effect and draft rule were analysed in theory,resolving methods were put forward according to existing problems in practice.It is pointed out that yarn quality could be improved effectively by adopting rubber-covered roll forward motion draft especially pure cotton carding yarn quality.The modification cost is lower.
Optimization and Design of Yarn Suction Duct on Automatic Cone Winding Machine

Wang Hui,Wu Yadong,Yu Wensheng

DOI: https://doi.org/10.3969/j.issn.1001-7415.2011.05.006

2011-01-01

Abstract:To improve automatic cone winding machine stability and work efficiency,problems existed in winding machine duct and the causes were analyzed.The yarn suction duct was optimized,new yarn suction duct with diversion pipelines and variable cross-section were designed.Through calculation,flow situation in yarn suction duct before and after optimization were contrasted.It is proved that the design is rational.It is considered that after the optimization,the pressure change of yarn suction duct is reduced,anti-jamming capability is increased,the stability and work efficiency of automatic cone winding machine can be improved.
Investigation of Groove Shape Variation During Steel Sheave Spinning

Chengcheng Zhu,Dean Meng,Shengdun Zhao,Shuaipeng Li

DOI: https://doi.org/10.3390/ma11060960

IF: 3.4

2018-01-01

Materials

Abstract:Large sheaves, such as crosshead sheaves, are foundation parts in the heavy industry. Counter-roller spinning steel sheaves are utilized to replace traditional casting iron parts. Few studies exist on the groove shape of these spinning sheaves. Consequently, it is significant to explore the spinning groove shape variation rule and confirm the appropriate spinning parameters. Both experimental and numerical methods were utilized to study the groove shape variation of Q235 steel sheaves and their results were well matched. Spring-back phenomena were considered in this study. The groove depth was lower than the spinning depth and the last formed groove was the deepest. The former groove depth would be affected by the adjacent following spinning process. The single groove spinning result was linearly dependent on the multiple spinning groove depth. Certain equations were used to calculate the groove depth. The bottom–middle–top spinning sequence, which was better than other spinning sequences, should be used in the sheave spinning method. A sheave spinning process could be designed based on the study to obtain a fine groove shape.
Application Analysis on Drawing Device of Differential Thread

Wei Liu,Yanping He,Jiaqi Cao,Sitong Liu,Yingying Chen

DOI: https://doi.org/10.4028/www.scientific.net/amm.614.565

2014-01-01

Abstract:In the field of mechanical installation and repairing, drawing devices are often used to disassemble or push up components of various types of axie and set. Differential thread usually consists of two sets of threads, which differ in the aspect of side pitch, the movement distance of differential thread when it runs a circle should be the deviation of the two spiral side pitches. Through the application of differential thread, it enables us to make changes in the transmission of these two screw pairs making relative movement. Based on this principle, when it is made into the application of manual drawing device, it optimized structure of drawing device, receiving a better result.
Theoretical Prediction of Flange Wrinkling in First-Pass Conventional Spinning of Hemispherical Part

Qingshuai Kong,Zhongqi Yu,Yixi Zhao,Hao Wang,Zhongqin Lin

DOI: https://doi.org/10.1016/j.jmatprotec.2016.07.031

IF: 6.3

2016-01-01

Journal of Materials Processing Technology

Abstract:Flange wrinkling is one of the most common defects in conventional spinning. A lot of work has been done to find the reason for the flange wrinkling and the way to avoid it. However, the theoretical prediction of flange wrinkling is limited for the non-uniformly distributed stresses and complicated boundary conditions of the flange. In this paper, a FE (Finite element) model is established to study the deformation characteristic of the material in conventional spinning, two stable compressive stress rings distributed at the middle surface of the formed part are found, and the outer stress ring distributed at the flange is considered to be the key factor of flange wrinkling. A theoretical flange wrinkling prediction method is proposed based on the plastic buckling theory and the energy method with the boundary conditions extracted from the FE simulation results. Experiments are designed to research the flange wrinkling phenomenon and verify the proposed theoretical flange wrinkling prediction method. At last, effects of feed ratio on flange wrinkling are analyzed by this method, it is concluded that the decrease of the circumferential compressive stresses distributed in the flange caused by low feed ratio reduces the risk of flange wrinkling.
A yarn-scale woven fabric model including significant slippage formulated within the Arbitrary Lagrangian Eulerian framework

J. Simon,N. Hamila,S. Comas-Cardona,C. Binetruy

DOI: https://doi.org/10.1016/j.cma.2023.116741

IF: 6.588

2024-01-12

Computer Methods in Applied Mechanics and Engineering

Abstract:A numerical model is proposed to simulate significant yarn slippage and unweaving in woven fabrics using the Arbitrary Lagrangian Eulerian (ALE) method. Woven fabrics were modeled at the yarn scale using 1D ALE elements with additional slip displacement degrees of freedom (DOF). The relatively weak bending stiffness of the yarn was included using a rotation-free approach. A weave kinematic constraint between crossing yarns allowed an efficient description of the deformation modes due to the yarn assembly such as in-plane shear. In particular, normal compaction at weave points was taken into account using an additional crimp amplitude DOF and couplings of the fabric's cohesion with the normal and lateral compaction were considered. To deal with yarn unweaving, a specific void-ALE 1D element was developed in order to avoid remeshing, time-step reduction (explicit scheme) and early deactivation of the weave kinematic constraint. To demonstrate the capabilities of this numerical model, common characterization tests such as in-plane and out-of-plane pullouts, which induced unweaving were simulated. Finally, a first forming simulation on a hemisphere was performed to verify whether the cohesion of the fabric remained well represented in situations without loss of cohesion before simulating forming on a prismatic punch involving significant yarn slippage.

mechanics,engineering, multidisciplinary,mathematics, interdisciplinary applications
Tuning drafting zone parameters for polyester yarn within a ring spinning system: modeling and optimization

Habib Amiri Savadroodbari,Milad Razbin,Mohsen Reza Hasani,Majid Safar Johari

DOI: https://doi.org/10.1080/00405000.2024.2368287

IF: 1.7698

2024-06-23

Journal of the Textile Institute

Abstract:Yarn is a fundamental element in most textile products. Among various yarn manufacturing methods, the ring spinning system is particularly important due to its benefits, such as high yarn quality, evenness, low hairiness, and ease of handling. The parameters of the drafting zone in this system greatly impact yarn quality. Typically, adjusting these parameters in the drafting zone is time-consuming and costly using trial-and-error method. This study introduces an algorithmic approach using response surface methodology (RSM), experimental modeling, and multi-objective optimization to decrease unevenness percentage (U%) and imperfection index (IPI). Input parameters optimized include cots hardness of front and back top rollers, spacer size, and break draft. Results showed that the artificial neural network (ANN) predicts response parameters superiorly with determination coefficient close to 1, compared to RSM, which has a determination coefficient of about 0.72. Therefore, ANN was chosen for optimization. Additionally, combining the genetic algorithm (GA) with two ANN-based models reduced IPI from 39 to 33.67 and a decreased from 9.73% to 9.67% occurred in terms of U%. The final Input settings were the cots hardness of the front roller of 70 shores and the cots hardness of the back roller of 76 shores, spacer size 2.8 mm, and break draft of 1.26. This method efficiently optimizes the drafting zone parameter, thus enhancing yarn quality.

materials science, textiles
Analysis of temperature and speed effects on the drawing stress for improving the wire drawing process

A. Haddi,A. Imad,G. Vega

DOI: https://doi.org/10.1016/j.matdes.2011.04.010

2011-09-01

Abstract:This paper deals with experimental investigations in order to study the influence of drawing conditions on temperature rise and drawing stress in cold drawn copper wires. In the multipass drawing machine, the temperature rise and drawing stress are measured with thermocouples and load cell systems, respectively, for different drawing speeds. The results obtained show that the drawing stress and temperature rise vary during the drawing process. This certainly comes from the variation of the friction coefficient and the flow stress of the material depending on the drawing speed. From the experimental results, a relationship between temperature rise, drawing stress and friction coefficient is built. Based on this, a modification of Avitzur’s model is presented. This new model can help to select the process parameters which satisfy the conditions of minimum drawing stress for copper material.

materials science, multidisciplinary
MACHANICAL ANALYSIS AND SIMULATION STUDY ON THE MIDDLE GROOVE CONNECTION SYSTEM OF SCRAPER CONVEYOR

DongSheng ZHANG,HaiYang YU,JiaNing JIANG,Yan LI,ZhenDuo SONG

DOI: https://doi.org/10.16579/j.issn.1001.9669.2018.02.036

2018-01-01

Abstract:In this paper,the central groove scraper conveyor connecting system as the research object,the mechanics model of middle groove connection system different postures,and were to push the slide and Lycra two kinds of stress conditions in central groove connection system were analyzed.ANSYS software simulation analysis of its static strength and fatigue life,results showed that the central groove connection system weakest place in the passage of the ear and dumbbells fossa,fossa stress concentration dumbbell caused by this result and the actual work damage convex tip matches and proposed to increase the size of the dumbbell nest rounded to reduce stress concentration and reduce stress peaks to resolve this issue.The study was designed scraper conveyor system connecting central groove provides a reference and theoretical basis.
Test Analysis of Improving CV Value in Spinning Production

Bo ZHAO

DOI: https://doi.org/10.3969/j.issn.1001-9634.2006.06.013

2006-01-01

Abstract:Process analysis finds out the impact factors of spinning value,namely,noil ratio,pre-draw ratio,draw process,spindle performance,hygrothermo factor.The main spinning accessories such as collector,cot,ring plus traveller and top cradle are tested.Conclusion is made that proper configuration of specifications in process of spinning,drawing and twisting sections plus good mechanical performance will be a good measure reducing spinning CV value.
Study on the friction characteristics of the bonding point of variable cross-section three-dimensional braided yarn increase based on the bonding method

Pan Cheng,Xinhai He,Hao Zhou,Fei Liu,Junhao Liang,Yubo Wei,Yanzhang Li

DOI: https://doi.org/10.1177/15280837231220077

2023-01-01

Journal of Industrial Textiles

Abstract:In the process of using adhesive method for variable cross-section 3D weaving, the introduction of adhesive at the yarn increasing point greatly increases the friction and wear between carbon fibers, which can lead to a decrease in the overall performance of the prefabricated component. In response to the above issues, a self-made experimental fixture was developed to test the friction and wear performance between carbon fibers in bonding process. The effects of friction angle, preloaded tension, and friction frequency on the friction properties between carbon fiber bundles were investigated. Solidworks is used to model bonded carbon fiber bundles with a friction angle of 90 degrees, and ABAQUS is used to simulate the friction of the bonded carbon fiber bundle. The experimental results show that stress concentration occurs in the center of the friction area, and the wear degree at the center is more obvious, and the number of fiber breaks at the center was more than that of the side. Friction angle has great influence on friction coefficient, while pre-tensioning and friction frequency had a negligible effect. Based on the above results, when performing variable cross-section 3D weaving, it is recommended to increase the spacing between adjacent carriers and shorten the distance between the weaving chassis and the prefabricated parts. Additionally, it is advised to reduce the pre-added tension on the carrier device and increase the knitting frequency as much as possible within the scope of working conditions. The study results are of great significance for developing 3D weaving devices in terms of theoretical and engineering guidance.
Theoretical Prediction of Flange Wrinkling in the First-Pass Conventional Spinning of Dual-Metal Sheets

Juan Huang,Junsong Jin,Lei Deng,Xinyun Wang,Pan Gong,Mao Zhang,Chang Gao

DOI: https://doi.org/10.1016/j.jmapro.2020.12.044

IF: 5.684

2021-01-01

Journal of Manufacturing Processes

Abstract:Flange wrinkling will occur when the dual-metal sheet is formed to a certain degree in conventional spinning, leading to forming failure, so it is necessary to study the flange wrinkling defects. In order to predict and avoid the flange wrinkling, a theoretical model for calculating the forming limit was proposed according to the energy method. Additionally, experiments and numerical simulations were conducted to study the wrinkling and verify the established model. Based on the above analytical model, forming limit diagrams of flange wrinkling in the first-pass conventional spinning were given, and the effects of roller feed rate (f), blank thickness (t), the thickness ratio (lambda) of each layer on the flange wrinkling of dual-metal sheets were further analyzed. It is concluded that increasing the roller feed rate and reducing the thickness of the dual-metal sheet will cause the flange to be more prone to instability and wrinkles. And analytical results are consistent with numerical and experimental results. Considering that the finite element (FE) model is difficult to set up, the theoretical method provides guidance for the selection of process parameters to avoid wrinkling defects.
Analysis Of The Improvement Of The Drawing Die In Drawing Device

Wei Liu,Dongmei Wang,Guihai Liu,Zeyu Zheng,Jiting Jiang

DOI: https://doi.org/10.4028/www.scientific.net/AMM.496-500.1041

2014-01-01

Applied Mechanics and Materials

Abstract:Drawing devices, as an important auxiliary equipment, nowadays widely applied in areas such as mechanical installation, machinery manufacturing, machinery repair, but still have problems to fit into the workpiece of larger size and of difform shape. The article presehts a new kind of drawing device with a novel drawing die,which not only well solve the problem mentioned but also greatly improve the use efficiency and the use value by analyzing the existing deficiency in drawing devices.

Approach on Relationship Between Drawing in Back Area and Slippage of Aprons

Approach into Relationship Between Drawing in Back Area and Slippage of Aprons

The Optimization of the Key Components of the Spinning Machine Conveyor System Based on ISIGHT

The influence of the friction field on accelerating position distribution

The influence rule of uneven input sliver on floating fiber motion during the dynamic drafting process

Analysis of Flowing Characteristics of Abrasive Flow Machining in Slit

Approach into Reduction of Fuzzy Yarn of Winding Bobbin

The Ⅱ Kind of Size Effect on Micro Deep Drawing

Processing Practice of Rubber-covered Roll Forward Motion Draft in Spinning Frame

Optimization and Design of Yarn Suction Duct on Automatic Cone Winding Machine

Investigation of Groove Shape Variation During Steel Sheave Spinning

Application Analysis on Drawing Device of Differential Thread

Theoretical Prediction of Flange Wrinkling in First-Pass Conventional Spinning of Hemispherical Part

A yarn-scale woven fabric model including significant slippage formulated within the Arbitrary Lagrangian Eulerian framework

Tuning drafting zone parameters for polyester yarn within a ring spinning system: modeling and optimization

Analysis of temperature and speed effects on the drawing stress for improving the wire drawing process

MACHANICAL ANALYSIS AND SIMULATION STUDY ON THE MIDDLE GROOVE CONNECTION SYSTEM OF SCRAPER CONVEYOR

Test Analysis of Improving CV Value in Spinning Production

Study on the friction characteristics of the bonding point of variable cross-section three-dimensional braided yarn increase based on the bonding method

Theoretical Prediction of Flange Wrinkling in the First-Pass Conventional Spinning of Dual-Metal Sheets

Analysis Of The Improvement Of The Drawing Die In Drawing Device