Abstract:The introduction of one-dimensional (1D), two-dimensional (2D), and three-dimensional (3D) ultrasounds into solidifying FeCoNiCuAl high-entropy alloy was efficiently optimized, which realized the maximum input of acoustic energy and the effective adjustment of the energy proportion between stable and transient cavitation effects. In addition to the ordinary advantage of grain refinement, the superiority of power ultrasound in modulating such Cu-containing high-entropy alloys with dendritic structures mainly lay in the significant regulation of phase volume fraction and the elimination of severe Cu element microsegregation. As the main energy transmission form under 1D ultrasound, stable cavitation slightly increased the nucleation rate of α and γ1 phases, which jointly contributed to suppressing the Cu solute enrichment from 41.6 to 36 at pct through the acoustic streaming during the subsequent growth of γ1 phase. When 2D and 3D ultrasounds were applied, the intensive transient cavitation dominated the solidification process. The induced local high undercooling resulted in the competitive nucleation and growth between α and γ1 phases, leading to the more than one order of magnitude reduction in their grain sizes and the significant rise of γ1 phase volume fraction from 13 up to 50 pct. Meanwhile, it strikingly reduced the final Cu content difference between these two phases from over 30 to around 3.8 at pct by decreasing the Cu composition in competitively formed γ1 nuclei. The above microstructure modification brought in excellent compressive property for 3D ultrasonically solidified alloy, whose strength and ductility were simultaneously enhanced by 27 and 24 pct.

Phase, Microstructure, and Properties of Fine-Grained Mo-W-Cu Alloys Prepared by Mechanical Alloying and Large Electric Current Sintering

Densification, Microstructure, and Properties of W-Mo-Cu Alloys Prepared with Nano-Sized Cu Powders Via Large Electric Current Sintering

Process Parameter Optimization and Improved Properties of Large Electric Current-Sintered Mo-W-Cu Alloys Using Orthogonal Analysis

Microstructure and Phases Investigations of W–Mo–Cu Alloy Prepared by Large Current Electric Field Sintering

Densification and Properties Investigation of W-Mo-Cu Composites Prepared by Large Current Electric Field Sintering with Different Technologic Parameter

Phase Evolution of Mo-W-Cu Alloy Rapid Prepared by Spark Plasma Sintering

Microstructure and properties of Mo-50%Cu alloy by mechanical milling and pressure-assisted solid state sintering

Modulating Phase Constitution and Copper Microsegregation for FeCoNiCuAl High-Entropy Alloy by Optimized Ultrasonic Solidification

Study on the Microwave Sintering of the Novel Mo–W–Cu Alloys

Study on the Electric Current Effects on the Microstructure and Properties of W-Mo-Cu Alloy Under the Action of Electric Field

Effects of electro-thermal cycles on the densification and properties of W-Mo-Cu alloys prepared via large current electric field sintering

Pressure Effects on a Novel W-Mo-Cu Alloy by Large Current Electric Field Sintering: Sintering Behavior, Microstructure and Properties

Preparation of W-Cu Alloy with High Density and Ultrafine Grains by Mechanical Alloying and High Pressure Sintering

Preparation of W–Al–Mo Ternary Alloys by Mechanical Alloying

Mechanical Properties And Microstructural Evolution Of Mo-Co-Co Strengthened W-Ni-Fe Alloys By Spark Plasma Sintering

The Influence of Ball Milling Conditions on the Powder Characteristics and Sintering Densification of Mo-Cu Alloy

Investigation on sintering and deformation strengthening of Mo-Cu alloy

Effect of Metastable Cr(Mo)s/Cr(Mo)a Powders on Mechanical Alloying the Immiscible Cu–Mo–Cr System

PREPARATION AND DENSIFICATION OF Mo-Cu ALLOY

The sintering behavior of ultra-fine Mo-Cu composite powders and the sintering properties of the composite compacts

Sintering characteristics of fine grained Mo-40Cu alloy