Abstract:The effect of major constituents (the Li content increases from 0.5 to 3 wt% and the Cu content decreases from 4.5 to 2 wt%) on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations. Increasing the Li content progressively raises the melting temperature from 520 °C in 1# alloy (Al-0.5Li-4.5Cu, wt%) and 2# alloy (Al-1Li-4.5Cu) to 560 °C in 6# alloy (Al-3Li-2Cu). In addition, the variations of the major constituents result in the changes of the type and volume fraction of the inter- and intra-granular intermetallic phases. TEM results indicate that minor modifications to alloy composition greatly alter precipitation behavior during isothermal aging. The Li-poor alloy (2# alloy) presents a much shorter incubation time of T1-Al2CuLi precipitate than the Li-rich alloy (Al-1.5Li-4.5Cu, 3# alloy), while the nucleation of θ'-Al2Cu precipitate is promoted in Li-rich alloy. No typical spherical δ'-Al3Li precipitate is observed in 2# and 3# alloys during isothermal aging, except for the as-quenched 3# alloy. The preferential nucleation of δ' precipitate on the coherent and broad face of θ' precipitate is observed in 2# and 3# alloys, leading to the formation of "sandwich-like" δ'/θ'/δ' phases. Further decreasing Cu content to 2 wt% and increasing Li content to 3 wt% (6# alloy), the predominant phase in the matrix is δ' precipitate, accompanied by a small amount of unevenly distributed θ' and T1 precipitates. The best balance between ductility and strength is obtained by 2# alloy aged for 32 h, but 6# alloy has significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over 2# alloy (density: 2.675 g/cm3; elastic modulus: 75.45 GPa).

New Insight into Enhancing the Comprehensive Mechanical Performance in Non-Stretched Al-Cu-Li-(Mg)-(Ag)-Mn-Zr Alloys

Regulation of precipitation behavior among T1, S', and θ' phases in Al–Cu–Li-(Mg–Ag) alloys by optimizing Ag/Mg ratios

Microstructure and Mechanical Properties of Mg, Ag and Zn Multi-Microalloyed Al–(3.2–3.8)Cu–(1.0–1.4)Li Alloys

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Microstructure and Mechanical Properties of Al–Cu–Mg–Mn–Zr Alloy with Trace Amounts of Ag

Insights into precipitation characteristics and strengthening mechanisms in a low Cu/Mg ratio Al-Cu-Mg-Ag alloy

Microstructural Characteristics and Mechanical Properties of Extruded Al-4Cu-1Li-0.4Mg-0.1Zr-xZn Alloy

Uncovering the origin of enhanced strengthening in Li-added Al–Cu–Mg alloys

Influences of Mg content on the microstructures and mechanical properties of cast Al–2Li–2Cu–0.2Zr alloy

Microstructure, Mechanical Properties, and Corrosion Behavior of Al-4.0Cu-1.1Li-0.5Mg-xAg Alloys

Tailoring the heterophase interfacial structures to improve both strength and ductility of Al-Li alloys by fine tuning major solute Mg

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Effect of Cu Content and Zn/Mg Ratio on Microstructure and Mechanical Properties of Al–Zn–Mg–Cu Alloys

Microstructures and Mechanical Properties of Al-Cu-Mg-(Ag, La) Alloys

Enhancing the Tensile Strength and Heat Resistance Induced by High-Density Ω Phases in an Al–Cu–Mg–Ag Alloy

Effect of Zn on Precipitation Evolution and Mechanical Properties of a High Strength Cast Al-Li-Cu Alloy

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Alloying Role of Trace Mg and Ag Element in Al-5.8Cu-0.3Mn Alloy

Precipitate microstructures, mechanical properties and corrosion resistance of Al-1.0 wt%Cu-2.5 wt%Li alloys with different micro-alloyed elements addition

Co-strengthening of the Multi-Phase Precipitation in High-Strength and Toughness Cast Al–Cu–Zn–Mg Alloy Via Changing Zn/Mg Ratios

The effect of major constituents on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy