Abstract:<p>A novel dual-serpentine-channel flat-plate oscillating heat pipe (FPOHP) is designed and fabricated for electronic cooling with multiple heat sources and sinks. The FPOHP has two mirror symmetric tandem branches of capillary serpentine square channel with a hydraulic diameter of 2 mm (i.e., Bond number <em>Bo</em> = 1.137~1.265 here), which is made of 6063 aluminum alloy and 55% partially filled with acetone. A corresponding experimental study is conducted to investigate the start-up characteristics and quasi-steady thermal performance of the FPOHP with arrangement of "uniform heating by multiple heat sources at center and air cooling at both ends" under different inclination angles. The combined flow pattern diagrams as well as thermal resistance and equivalent thermal conductivity contour maps are provided for two mirror symmetric tandem sections of the FPOHP, based on which the thermo-hydrodynamic performance deviations between these two sections are compared and analyzed. The results show that the quasi-steady fluid motions in the FPOHP can be characterized by intermittent or independent occurrence of three elements, namely, stop, oscillation, and circulation, depending on the heat load and inclination angle. Significantly, the thermo-hydrodynamic behaviors in two tandem sections of the FPOHP both cooperate and compete with each other, as a result of the heat, mass and momentum exchanges via the tandem structure. The FPOHP can start up successfully under all inclination angles from 0° to 90° with no obvious difference, and its start-up temperature increases smoothly and approximately reaches a plateau of 41~46 °C as the heat load goes up. For the 175 tested conditions, the coefficients of variation for the thermal resistance of two tandem sections are smaller than 21.5% with the average value of 6.8%, showing a fine heat transfer uniformity of the FPOHP over a wide range of operating conditions. Significantly, in general, the FPOHP has much larger overall equivalent thermal conductivity (about 5.8 times on average) and possesses only a weight 83.6% of a pure 6063 aluminum alloy plate with the same geometry. In addition, the FPOHP exhibits a well gravity adaptability with the relative deviation ranging from 7.1% to 25.2% in the total thermal resistances for all inclination angles. Accordingly, the FPOHP shows a good potential for the high-heat-flux electronic cooling applications with multiple heat sources and sinks.</p>

Investigation of Thermo-Hydrodynamic Characteristics in Micro-Oscillating Heat Pipe by Alternatively-Arranged Ratchet Microchannels

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Thermo-hydrodynamic characteristics of a novel flat-plate micro pulsating heat pipe with asymmetric converging-diverging channels

High-Speed Visual Analysis of Fluid Flow and Heat Transfer in Oscillating Heat Pipes with Different Diameters

Fluid Flow and Heat Transfer in Flat-Plate Oscillating Heat Pipe

Experimental investigation of flow visualization and thermal performance of flat-plate single-loop pulsating heat pipes

Experimental Investigation of Heat Transfer Characteristics in a Miniature Flat Heat Pipe with Multi-Channels

Thermal performance of a novel dual-serpentine-channel flat-plate oscillating heat pipe used for multiple heat sources and sinks

Relating the thermal properties of a micro pulsating heat pipe to the internal flow characteristics via experiments, image recognition of flow patterns and heat transfer simulations

Heat Transfer Enhancement of Horizontal Oscillating Heat Pipes with Micro-/Nanostructured Surface

Effect of geometries on the heat transfer characteristics of flat-plate micro heat pipes

Experimental study on microcapsule fluid oscillating heat pipe

Thermo-hydraulic analysis in double-layered microchannels with porous rib and phase change microcapsules slurry as coolant

Evaluation of the Heat Transfer Performance of a Device Utilizing an Asymmetric Pulsating Heat Pipe Structure Based on Global and Local Analysis

Experimental Study on Thermal Performance of a Novel Serpentine-Looped Flat Microchannel Heat Pipe

Experimental and Theoretical Study on Operation Characteristics of an Oscillating Heat Pipe

Simulation of a miniature oscillating heat pipe in bottom heating mode using CFD with unsteady modeling

Analysis of two-phase flow patterns transition and heat transfer in flat plate loop pulsating heat pipe

Experimental Study on Effective Range of Miniature Oscillating Heat Pipes

Experimental and simulation study on flow heat transfer characteristics of flat pulsating heat pipe with wide and narrow interphase channels