Abstract:<p>A novel dual-serpentine-channel flat-plate oscillating heat pipe (FPOHP) is designed and fabricated for electronic cooling with multiple heat sources and sinks. The FPOHP has two mirror symmetric tandem branches of capillary serpentine square channel with a hydraulic diameter of 2 mm (i.e., Bond number <em>Bo</em> = 1.137~1.265 here), which is made of 6063 aluminum alloy and 55% partially filled with acetone. A corresponding experimental study is conducted to investigate the start-up characteristics and quasi-steady thermal performance of the FPOHP with arrangement of "uniform heating by multiple heat sources at center and air cooling at both ends" under different inclination angles. The combined flow pattern diagrams as well as thermal resistance and equivalent thermal conductivity contour maps are provided for two mirror symmetric tandem sections of the FPOHP, based on which the thermo-hydrodynamic performance deviations between these two sections are compared and analyzed. The results show that the quasi-steady fluid motions in the FPOHP can be characterized by intermittent or independent occurrence of three elements, namely, stop, oscillation, and circulation, depending on the heat load and inclination angle. Significantly, the thermo-hydrodynamic behaviors in two tandem sections of the FPOHP both cooperate and compete with each other, as a result of the heat, mass and momentum exchanges via the tandem structure. The FPOHP can start up successfully under all inclination angles from 0° to 90° with no obvious difference, and its start-up temperature increases smoothly and approximately reaches a plateau of 41~46 °C as the heat load goes up. For the 175 tested conditions, the coefficients of variation for the thermal resistance of two tandem sections are smaller than 21.5% with the average value of 6.8%, showing a fine heat transfer uniformity of the FPOHP over a wide range of operating conditions. Significantly, in general, the FPOHP has much larger overall equivalent thermal conductivity (about 5.8 times on average) and possesses only a weight 83.6% of a pure 6063 aluminum alloy plate with the same geometry. In addition, the FPOHP exhibits a well gravity adaptability with the relative deviation ranging from 7.1% to 25.2% in the total thermal resistances for all inclination angles. Accordingly, the FPOHP shows a good potential for the high-heat-flux electronic cooling applications with multiple heat sources and sinks.</p>

Thermo-hydrodynamic characteristics of a novel flat-plate micro pulsating heat pipe with asymmetric converging-diverging channels

Experimental Investigation on the Heat Transfer Performance and Evaporation Temperature Fluctuation of a New-Type Metal Foam Multichannel Heat Pipe

Experimental Research on the Start-Up Characteristics and Heat Transfer Performance of Pulsating Heat Pipes with Rectangular Channels

Review of the Development of Pulsating Heat Pipe for Heat Dissipation

Investigation on the Influence of Different Heat Transmission Distances on Thermo-Hydrodynamic Characteristics of Pulsating Heat Pipes

Experimental investigation on heat transfer performance of closed-loop pulsating heat pipe with large inner diameter

Experimental Investigation on the Temperature Distribution Characteristics of the Evaporation Section in a Pulsating Heat Pipe

An Experimental Investigation on the Heat Transfer Characteristics of Pulsating Heat Pipe with Adaptive Structured Channels

Experimental Study on the Thermo-Hydrodynamic Characteristics of a Nitrogen Pulsating Heat Pipe

Relating the thermal properties of a micro pulsating heat pipe to the internal flow characteristics via experiments, image recognition of flow patterns and heat transfer simulations

Numerical Study of the Thermal Performance of a Hydrogen Pulsating Heat Pipe

Experimental and simulation study on flow heat transfer characteristics of flat pulsating heat pipe with wide and narrow interphase channels

Analysis on Heat Resistance of the Micro Heat Pipe with Arteries

Liquid Plug Characteristics and Heat Transfer Performance of a Silicon-Based Ultra-Thin Flat Heat Pipe at Different Incline Angles

Evaluation of the Heat Transfer Performance of a Device Utilizing an Asymmetric Pulsating Heat Pipe Structure Based on Global and Local Analysis

Experimental investigation on the thermal performance of high-concentrated photovoltaic module utilizing the thermal sink of a novel Fan-shaped plate pulsating heat pipe

Experimental Study of Thermal Performance of Pulsating-Heat-Pipe Heat Exchanger with Asymmetric Structure at Different Filling Rates

Experimental Study on Heat Transfer Performance Using a Hybrid Cooling Method Combined of a Flat-Plate Heat Pipe and Spray Cooling

Performance characteristics of pulsating heat pipes as integral thermal spreaders

Thermal performance of a novel dual-serpentine-channel flat-plate oscillating heat pipe used for multiple heat sources and sinks

Numerical investigation on the start-up and heat transfer performance of dual-diameter pulsating heat pipes