Abstract:Fe-6.5wt% Si non-oriented electrical steel sheets with a thickness of 0.50mm were produced by using a new processing route: strip casting followed by hot rolling, intermediate temperature (150–850°C) rolling and final annealing. The present study focused on exploring the effects of rolling temperature varying from 150 to 850°C on the microstructure and texture evolution, the formability and final magnetic properties. The microstructure and texture evolution at the various processing steps were investigated in detail by using OM, XRD, EBSD and TEM. It was found that the formability during rolling, the microstructure and texture before and after annealing and final magnetic properties highly depended on rolling temperature. The formability during rolling was gradually improved with increasing rolling temperature due to the slipping of dislocation. In particular, the rolling temperature dominated the formation of in-grain shear bands in the rolled microstructure, which played an important role in the development of final recrystallization microstructure and texture. In the case of lower temperature (150–450°C) rolling, an inhomogeneous microstructure with a large amount of in-grain shear bands was formed in the rolled sheets, which finally resulted in a fine and inhomogeneous annealing microstructure dominated by mild λ-fiber texture composed of cube and {001}〈210〉 components and α*-fiber texture concentrated on {115}〈5–10 1〉 component. By contrast, in the case of higher temperature (650–850°C) rolling, a relatively homogeneous microstructure without in-grain shear bands was formed instead in the rolled sheets, which finally led to a coarse and relatively homogeneous annealing microstructure characterized by strong α-fiber and γ-fiber texture. Accordingly, on the whole, both the magnetic induction (B8 and B50) and iron loss (P15/50 and P10/400) decreased with raising rolling temperature.

Production of 2 μm-thick 6.5 % Si-Fe cold rolled sheet

Near net shape fabrication of anisotropic Fe-6.5%Si soft magnetic materials

Microstructural Evolution in Warm-Rolled and Cold-Rolled Strip Cast 6.5 Wt% Si Steel Thin Sheets and Its Influence on Magnetic Properties

Development of Λ-Fiber Recrystallization Texture and Magnetic Property in Fe–6.5wt% Si Thin Sheet Produced by Strip Casting and Warm Rolling Method

Microstructure & Texture Evolution and Magnetic Properties of High Magnetic-Induction 6.5% Si Electrical Steel Thin Sheet Fabricated by A Specially Designed Rolling Route

Effect of annealing temperature on magnetic properties of cold rolled high silicon steel thin sheet

Experimental Study on the Twin Roll Strip Casting and Warm Rolling Fe-6.5 Wt. %si Steel Sheet

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Fabrication of Fe-6.5wt%Si Ribbons by Melt Spinning Method on Large Scale

Effects of Warm Temper Rolling on Microstructure, Texture and Magnetic Properties of Strip-Casting 6.5wt% Si Electrical Steel

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Magnetic and Mechanical Properties of the High Purity Fe-3 mass%Si Alloy by Cold Crucible Levitation Melting

Microstructure and texture evolution of thin-gauge non-oriented silicon steel with high permeability produced by twin-roll strip casting

Magnetic properties and crystallization behavior of Fe-based nanocrystalline strips fabricated by twin-roll casting

Fabrication and properties of strip casting 4.5 wt% Si steel thin sheet

Ultra‐Thin 3.5%Si Steel with Both Magnetic Properties and Mechanical Properties Produced by Different Process Routes of Large‐Scale Production

Numerical modeling investigation of Planar Flow Casting for Fe-6.5wt%Si alloy

A study of electromagnetic characteristics of Fe-Si-Al magnetic alloy

Effects of rolling temperature on microstructure, texture, formability and magnetic properties in strip casting Fe-6.5wt% Si non-oriented electrical steel

Electron Microscopy and Magnetic Properties of Fe-Cr-Co-Si Permanent Magnet Alloys Manufactured by Rolling-Ageing Technique

A quasi-in-situ EBSD study on the formation and development of η-fiber in 0.15 mm ultra-thin Fe-4.5 wt. % Si sheet