Abstract:This study explores the precision micro-machining of CoCrFeNiAlX short fiber-reinforced 7A09 aluminum matrix composites, focusing on the interplay between machining parameters and composite properties. The investigation scrutinizes the influence of vibrational amplitude, oscillation frequency, penetration depth, fiber orientation, and aluminum concentration on machining dynamics. Findings reveal that enhancing the X-axis vibrational amplitude to 80 μm is associated with a decrease in machining force, which then rises after reaching a threshold. In contrast, maintaining the Y-axis amplitude below 90 μm significantly increases the machining force. Higher amplitudes and frequencies were observed to reduce machining forces by up to 57% at an ultrasonic frequency of 15 kHz. Employing ultrasonically assisted vibration cutting (UEVC) culminated in a substantial 72% decrease in machining forces when fibers were optimally oriented at 45°. The study also identifies a direct correlation between the cutting temperature and both the vibrational amplitude and penetration depth, with the Y-axis amplitude having a more significant impact, causing a 55% variation in temperature. An increase in frequency initially lowers the cutting temperature, with the lowest temperature of 92 °C achieved at 5 kHz, while the peak temperature occurs at a machining depth of 60 μm. Temperature profiles indicate an initial rise with increased fiber orientation, followed by a decline. A slight increase in aluminum concentration marginally raises the cutting temperature. Furthermore, UEVC is found to produce a parabolic residual stress distribution, where amplitude and penetration depth determine the peak stress levels, and higher frequencies contribute to stress reduction. Fiber orientation also affects residual stress, with proper alignment reducing compressive stress and misalignment increasing it. The lowest point of residual compressive stress is detected in the Al0.6 fiber composite, while the peak is observed in the Al1 composites.

Revealing the mechanical responses and accommodation mechanisms of Cu-based amorphous composites under elastic preload and ultrasonic vibration treatment

Experimental Study on Stress Wave Propagation in Ultra High Toughness Cementitious Composites

Molecular dynamics study of acoustic softening effect in ultrasonic vibration assisted tension of monocrystalline/polycrystalline coppers

Microscopic impacts of ultrasonic vibration on interfacial strength of SiCp/Al composites

Effects of ultrasonic cavitation on microstructure and surface properties of Mn–Cu alloy

Ultrasonic elliptical vibratory nanocutting mechanisms of Cu 50 Zr 50 amorphous alloy: A molecular dynamics simulation

Ultrasonic and size effects on the rheological behavior of CoCrFeMnNi high-entropy alloy

Effects of void shape and location on the fracture and plastic deformation of Cu (crystalline) /Cu 64 Zr 36 (amorphous) composites

Grain Size Effects on the Rheological Behavior of Ti2AlNb-Based Alloy by Transverse Ultrasonic Vibration-Assisted Compression

Influence of Superimposed Ultrasound on Deformability of Cu

Ultrasonic vibration-induced amorphization in the Cu-Al interface

Experimental characterization on fracture behavior of UHPMC under small-scale sample tensile testing: Acoustic emission monitoring and digital image correlation

High-entropy alloy and amorphous alloy composites fabricated by ultrasonic vibrations

Longitudinal amplitude effect on material removal mechanism of ultrasonic vibration-assisted milling 2.5D C/SiC composites

Ultrasonic probing of the elastic properties of PMMA bead packings and their rearrangement during pressure sintering

Microstructure and mechanical properties of Al-Cu alloy with 0.6%Fe produced with ultrasonic vibration and applied pressure

Microstructure and Mechanical Properties of Cu-CoatedCarbon-Nanotubes-Reinforced Aluminum Matrix Composites Fabricated by Ultrasonic-Assisted Casting

Ultrasonic vibration-induced severe plastic deformation of Cu foils: effects of elastic-plastic stress wave bounce, acoustic softening, and size effect

The effects of ultrasonic vibration on mechanical properties of tungsten particle-reinforced copper-matrix composites

Ultrasonic elliptical vibration micro-cutting mechanism of CoCrFeNiAlX short fiber reinforced aluminum-based composite

The Effect of Superimposed Ultrasonic Vibration on Tensile Behavior of 6061-T6 Aluminum Alloy