Abstract:Extension twinning is not only a key plastic deformation mode of Mg and its alloys at room temperature (RT), but also introduces high density of dislocations and changes crystal orientation (texture) which exert considerable influence on precipitation strengthening and mechanical properties. Using tensile test, quasi-in-situ hardness test, optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the effects of extension twinning on age-hardening, precipitation behavior and mechanical properties of an extruded AZ80 bar were investigated. Extension twins were introduced into the bar by cold compressed (H1) along extrusion direction (ED), and two kinds of aging treatments, i.e. ‘on-line quenching + aging’ (T5) and ‘on-line quenching + H1 + aging’ (T10), were conducted at 150 °C. We clarified that extension twinning can significantly accelerate precipitation kinetics. For T5 aging, there is an incubation stage in the first 15 h, and then the hardness increases continually and slowly in the following 35 h. By contrast, for T10 aging, softening is caused in the first 2.5 h, and then the hardness increases linearly until 20 h and remains stable in the next 30 h. Discontinuous precipitation is predominant in T5 aging; however, discontinuous precipitation is mostly inhibited in T10 aging and at the same time nano-sized continuous precipitates with high number density are formed in both extension twins and matrixes. Extension twins contains higher dislocation density and thus denser continuous precipitates than matrixes. Both and dislocations can be seen in extension twins and matrixes. Mechanical properties have been largely improved by extension twins. Particularly, after T10 the ED tensile yield strength (Rp0.2) remarkably increases from 144 MPa (H1) to 206 MPa, indicating that dense nano-sized continuous precipitates can effectively hinder twin-boundary migration during the detwinning. Moreover, T10 can obviously diminish the machinal property anisotropy as compared with T5.

Effect of Preset Twins on Aging Precipitates and Mechanical Properties of Mg-5gd-3y-0.5zr Alloy

Effects of solid solution and aging process on microstructure and mechanical properties of Mg-Gd-Y alloy

Twin-twin Geometric Structure Effect on the Twinning Behavior of an Mg-4Y-3Nd-2Sm-0.5Zr Alloy Traced by Quasi-in-situ EBSD

Effect of twin assisted precipitation on the microstructure and mechanical properties of gradient structure Mg-Gd-Zn-Zr alloy

Microstructure Evolution and Selection Behavior of Twin Variants of Mg-5Gd-3Y-0.5Zr Alloy during Secondary Deformation

The Effect of Precipitates on Voiding, Twinning, and Fracture Behaviors in Mg Alloys

Enhanced Precipitation Strengthening of Extruded Mg-8 Wt.%al-0.5 Wt.%zn (AZ80) Magnesium Alloy by Extension Twinning

Improvement of dynamic compression properties and strengthening mechanism of Mg–Y–Nd–Gd–Zr alloy by pre-twinning

Effect of Twin and Grain Size Strengthening on Tensile Properties of a Multi-Directionally Impact Forged Mg–Gd–Y Alloy

Effect of Sm on Twinning Behavior of Mg-Gd-Y-Zr Alloy at Room Temperature Compression

{10–12} Twinning Relationship in Mg-Gd-Y(-Sn)-Zr Alloys under Uniaxial Compression at Room Temperature

Influence of precipitation on tension and compression twinning in Mg-6.5Zn alloy

The Effect of Twins on Mechanical Properties and Microstructural Evolution in AZ31 Magnesium Alloy during High Speed Impact Loading

The Effect of Precipitates on the Fracture Behavior and Tensile Properties of Mg–14Gd–0.5Zr (wt.%) Alloy

Growth Twinning Behavior of Cast Mg–Zn–Cu–Zr Alloys

Effect of Yb Addition on the Microstructure and Mechanical Properties of the Mg–4Sm–3Gd–0.5Zr Alloy

On the strengthening and slip activity of Mg-3Al-1Zn alloy with pre-induced { 10 1 ̄ 2 } twins

Effect of twinning on the deformation behavior of an extruded Mg-Zn-Zr alloy during hot compression testing

Effect of Zn Addition on Microstructure and Mechanical Properties after Extrusion, Rolling and Ageing in Mg-9Gd-3Y-0.5Zr Alloys

Effects of Precipitate on the Slip Activity and Plastic Heterogeneity of Mg-11Y-5Gd-2Zn-0.5Zr (wt. %) During Room Temperature Compression

The Effect of Basal Dislocation on 112¯1 Twin Boundary Evolution in a Mg-Gd-Y-Zr Alloy