Abstract:The scope of this work is to provide an overview of the influences of process parameters, print orientation, and post-process treatments of Ti6AlV4 processed by laser powder bed fusion on its microstructure and physical and mechanical properties and their anisotropic behavior. To avoid the influence of changes in powder quality and ensure comparability, experiments were carried out using a single batch of virgin powder. First, characterization of the density and surface roughness was performed to optimize the process parameters utilizing design of experiment. Tensile, notched bar impact and compression test specimens were built in three different orientations: vertically, horizontally, and inclined at 45° to the build plate. Later, the influence of the staircase effect and the possible course of anisotropy from vertical to horizontal were investigated. Subsequently, heat treatments for stress relief, furnace annealing, and hot isostatic pressing were performed. In addition to as-built samples, mechanical machining and a two-step electrochemical polishing surface treatment were applied to investigate the influence of the surface roughness. With parameter optimization, a relative density of 99.8% was achieved, and surface roughness was improved over default parameters, reducing Ra by up to 7 μm. Electrochemical polishing is a viable way to decrease the surface roughness. An Ra value of 1 μm and an Rz value of 4 μm can be achieved for 45° downskin surfaces with as-built surface roughness values of Ra 24 μm and Rz 117 μm. As-built and stress-relieved conditions show little anisotropy in their yield and tensile strength (max 2.7%), but there is a strong influence of the build orientation on necking, and brittle fracture behavior is shown due to the martensitic microstructure (up to 70%). Heat treatment can increase the ductility and further decrease the strength anisotropy with both furnace annealing and hot isostatic pressing delivering similar results for tensile properties, while angled samples exhibit behavior that is closer to vertical than horizontal, indicating a non-linear change in break behavior. Electrochemical polishing increases fracture necking, and its isotropy drastically increases from 4% to over 30% compared with as-built parts, which is close to the level of the machined specimen.

Effects of Powder Surface Conditions on the Rheological Behavior of Ti–6Al–4 V Alloy Powders for Additive Manufacturing

Effect of Particle Size Distribution on the Printing Quality and Tensile Properties of Ti-6Al-4V Alloy Produced by LPBF Process

Influence of particle morphology and size distribution on the powder flowability and laser powder bed fusion manufacturability of Ti-6Al-4V alloy

Effects of the process parameters on the formability and properties of Ni54(at.%) Ti alloys prepared by laser powder bed fusion

Effects of Ti6al4v Powder Oxidation on Process Dynamics in Laser Powder Bed Fusion Additive Manufacturing

Effects of Feedstock Powder on Wear, Corrosion, and Tribocorrosion Performances of Ti-6.5Al-2Zr-1Mo-1V Fabricated by Additive Manufacturing

Wet chemical surface functionalization of AA2017 powders for additive manufacturing

Reuse of Ti6Al4V Powder and Its Impact on Surface Tension, Melt Pool Behavior and Mechanical Properties of Additively Manufactured Components

Influence of the Properties of Ti6Al4V Powder Materials on the Build Quality of Laser Powder Bed Fusion–manufactured Components

Investigation of an Increased Particle Size Distribution of Ti-6Al-4V Powders Used for Laser-Based Powder Bed Fusion of Metals

In situ monitoring the effects of Ti6Al4V powder oxidation during laser powder bed fusion additive manufacturing

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Effect of In Situ 2%TiB<sub>2</sub> Particles on Microstructure and Mechanical Properties of 2024Al Additive Manufacturing Alloy

On thermal properties of metallic powder in laser powder bed fusion additive manufacturing

Laser powder bed fusion additively manufactured thin lightweight Ti6Al4V features: an experimental investigation on the influence of powder feedstock, geometry, and process parameters on property/quality

Influence of the physicochemical properties of reusable powders on the mechanical properties of Ti6Al4V manufactured via laser powder bed fusion additive manufacturing

Powder preparation during ball milling and laser additive manufacturing of aluminum matrix nanocomposites: Powder properties, processability and mechanical property

Simultaneous Enhancement of Powder Properties, Additive Manufacturability, and Mechanical Performance of Ti–6Al–4V Alloy by 2D-Nanocarbon Decoration

Influences of Surface, Heat Treatment, and Print Orientation on the Anisotropy of the Mechanical Properties and the Impact Strength of Ti 6Al 4V Processed by Laser Powder Bed Fusion

Development of Ti 6zr 5fe Alloy Powder for Laser Powder Bed Fusion

Effect of Process Parameters on the Mechanical Behavior of Ti6Al4V Alloys Fabricated by Laser Powder Bed Fusion Method