Abstract:The most important advantage of additive manufacturing by laser powder bed fusion (PBF-LB) technique is the ability to produce geometrically complex parts, but the problem is their rough surfaces, often difficult or inaccessible to finish by machining. Therefore, research to improve the reproducibility of the mechanical behavior of parts manufactured from aluminum alloy powders with as-built surfaces is of vital importance for the aerospace and automotive industries. Since local notches occurring on rough surfaces after the PBF-LB process are unavoidable, the way to solve this problem is to obtain as-built surfaces of the highest possible quality and to adapt a post-process heat treatment that increases the ductility and fracture toughness of the material. To this end, the present work focused on the study of the mechanical performance of AlSi7Mg0.6 samples with a rough as-built surface in the as-built state and after several variants of post-process heat treatment, combined with a detailed analysis of the microstructures corresponding to these states. Tensile samples built on a platform preheated to 100 °C, achieved a relative density of 99.85%, satisfactory surface quality, a relatively low level of residual stress and moderate crystallographic texture. Despite the rough surface, the samples under the as-built condition and after different variants of heat treatment (direct aging (DA), stress relieving (SR), and solution annealing followed by artificial aging (T6)), achieved tensile properties comparable to those reported in the literature for PBF-LB samples with machined surfaces. The resulting combinations of tensile properties of PBF-LB samples after different heat treatment variants were evaluated using the quality index (QI) commonly used to assess the quality of heat-treated Al-Si-Mg castings. It was found that the proposed T6 treatment provides the best combination of strength properties and ductility, compared to those obtained after both DA and SR, as well as after T6 treatment of high-quality castings, from the point of view of reducing the sensitivity of AlSi7Mg0.6 alloy to surface roughness.

Wet chemical surface functionalization of AA2017 powders for additive manufacturing

Metal powder as feedstock for laser-based additive manufacturing: From production to powder modification

Coated Metal Powders for Laser Powder Bed Fusion (L-PBF) Processing: A Review

Optimisation of the laser polishing for laser-powder bed fusion and electron beam-powder bed fusion Ti6Al4V surfaces

Physical Characterization and Rheological Behavior of AA 2017 Powder Modified with Al-5.0Nb-0.5B Inoculant Powder for Laser-based Powder Bed Fusion

Characterization, preparation, and reuse of metallic powders for laser powder bed fusion: A review

Modification of surface characteristics and electrochemical corrosion behavior of laser powder bed fused stainless-steel 316L after laser polishing

Surface wettability patterning of metal additive manufactured parts via laser-assisted functionalization

Processability of A6061 Aluminum Alloy Using Laser Powder Bed Fusion by In Situ Synthesis of Grain Refiners

New Aluminum Alloys Specifically Designed for Laser Powder Bed Fusion: A Review

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Effects of powders and process parameters on density and hardness of A357 aluminum alloy fabricated by selective laser melting

High-quality surface smoothening of laser powder bed fusion additive manufacturing AlSi10Mg via intermittent electrochemical polishing

Ongoing Challenges of Laser-Based Powder Bed Fusion Processing of Al Alloys and Potential Solutions from the Literature—A Review

High Absorptivity Nanotextured Powders for Additive Manufacturing

A Surface Quality Optimization Strategy Based on a Dedicated Melt-Pool Control Via the Dashed-Scan Contouring Technique in Electron Beam Powder Bed Fusion

Optimization of Laser Based-Powder Bed Fusion Parameters for Controlled Porosity in Titanium Alloy Components

Improved Process Efficiency in Laser-Based Powder Bed Fusion of Nanoparticle Coated Maraging Tool Steel Powder

Influence of the physicochemical properties of reusable powders on the mechanical properties of Ti6Al4V manufactured via laser powder bed fusion additive manufacturing

Effect of Powder Spreading Parameters on Laser Absorption Behavior and Processability of High‐Strength Aluminum Alloy Fabricated by Laser Powder Bed Fusion