Abstract:With the advancement of science and technology and the construction of metal-based composites (MMC), it became possible to achieve improved properties that were not easily available in an alloy. In fact, with the emergence of such technology, manufacturers were able to adjust the resulting materials according to their needs in such a way as to provide mechanical strength, hardness, corrosion resistance, or other desired properties. These composites were used in various aerospace, automotive, construction, and production industries. Aluminum-based composites are among the structures that have taken an important place in the industry due to their lightweight and high strength. The present study produced bi-alloy aluminum-based 1060/5083 composites fabricated with alumina particles with a Hot ARBp at T = 380 °C. Also, the effect of rolling steps on the roll bonding mechanism is investigated using numerical simulation. As the novelty of this study and for the first time, a bi-alloy 1050/5083 composites reinforced Al 2 O 3 particles via ARB process have been produced and then, potential dynamic polarization in 3.5 Wt% NaCl solution was used to study the corrosion properties of these composites. The corrosion behavior of these samples was compared and studied with that of the annealed aluminum. The study aimed to investigate the bonding behavior between the bi-alloy layers. So, as a result of enhancing influence on the number of ARBp, this experimental investigation revealed a significant enhancement in the main electrochemical parameters and the inert character of the Alumina particles. Reducing the active zones of the material surfaces could delay the corrosion process. Results showed that the corrosion resistance of the sample fabricated after six steps improved more than 100 % in comparison with the initial annealed Al alloy. Also, the average peeling force improved from 45 N to 94 N for the sample fabricated with six steps. Moreover, at a higher number of steps, the corrosion of MMC improved. Moreover, increasing the number of ARBsteps illustrated an improvement in the wear resistance of samples. Finally, the samples' bonding interface, corrosion surface, and peeled surface were investigated using scanning electron microscopy (SEM).

Investigation on Various Ceramic Nanoparticles Reinforced Aluminum Matrix Composites Via Accumulative Roll Bonding and Cryorolling

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Microstructure, Mechanical and Thermal Properties of Al/Cu/SiC Laminated Composites, Fabricated by the ARB and CARB Processes

A novel way to fabricate high elastic modulus and high strength of TiC reinforced aluminum matrix composite

Integrating Experimental and Computational Analyses for Mechanical Characterization of Titanium Carbide/Aluminum Metal Matrix Composites

Microstructure and Mechanical Properties of AA1050/AA6061 Laminated Composites Fabricated through Three-Cycle Accumulative Roll Bonding and Subsequent Cryorolling

On the microstructural and mechanical responses of dual-matrix Al-Ni/SiC composites manufactured using accumulative roll bonding

High Strength and Thermal Stability of Multilayered Cu/Al Composites Fabricated Through Accumulative Roll Bonding and Cryorolling

Evolution of Microstructure, Texture and Mechanical Properties for Multilayered Al Matrix Composites by Accumulative Roll Bonding

Microstructural evolutions and mechanical properties of multilayered 1060Al/Al–Al2O3 composites fabricated by cold spraying and accumulative roll bonding

Mechanical, microstructural, and textural evaluation of aluminum-MWCNT composites manufactured via accumulative roll bonding at ambient condition

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Study of mechanical properties and wear resistance of nanostructured Al 1100/TiO2 nanocomposite processed by accumulative roll bonding

EFFECTS OF HOT-ROLLING PROCESSES ON THE FRACTURE BEHAVIORS AND MECHANICAL PROPERTIES OF 2009Al/SiCp METAL MATRIX COMPOSITES

Fabrication, microstructure, mechanical properties and wear behavior of Al/Cu-SiC w composite

Microstructure and mechanical properties of AA1050/AA6061 multilayer composites via accumulative roll bonding and cryorolling and subsequent aging

Study on microstructure evolution and fracture behavior of Al/Al/Cu multilayer composites

Study of changes in the aging process, microstructure, and mechanical properties of AA2024-AA1050 nanocomposites created by the accumulative roll bonding process, with the addition of 0.005 vol.% of alumina nanoparticles

Fracture toughness, wear, and microstructure properties of aluminum/titanium/steel multi-laminated composites produced by cross-accumulative roll-bonding process

Fabrication, microstructure characterization and mechanical properties of B4C microparticles and SiC nanowires hybrid reinforced aluminum matrix composites

Corrosion and mechanical properties of Al/Al 2 O 3 composites fabricated via accumulative roll bonding process: Experimental and numerical simulation