Abstract:An anion exchange membrane (AEM) with good ion conductivity and high durability is greatly needed in the area of electrochemical energy conversion and storage systems. An AEM with a phase separation morphology has been shown to be an efficient strategy. Here, we randomly tethered a fluorocarbon segment and a tri-quaternary ammonium side chain to the poly(phenylene oxide) (PPO) backbone (PPO-22-3QA8F), aiming to increase the thermodynamic immiscibility between the hydrophobic/hydrophilic units and thereby produce an AEM with better phase separation but suppressed water uptake. With the premise of similar ion contents, two AEMs tethered with tri-quaternary ammonium (PPO-8-3QA) and benzyltrimethylammonium (PPO-22-QA) were synthesized for comparison. Incorporating an additional hydrophobic side chain turned out to be an effective way to drive the membrane's phase separation and the formation of well-connected ion conducting channels. PPO-22-3QA8F exhibited the highest hydroxide conductivity among the three AEMs up to 83 mS cm-1 in Milli-Q water at 90 degrees C, which is over 2 times higher than that of PPO-8-3QA (39 mS cm-1) and PPO-22-QA (27 mS cm-1). In addition, PPO-223QA8F exhibited a reasonable water uptake of less than 20 wt% at room temperature and excellent alkaline stability in 1 M NaOH at 80 degrees C for 7 days. As the immersion time was extended to 21 days, the PPO-223QA8F membrane was ductile and retained 51% of its original conductivity, while the other two controls were broken to pieces. A H2/O2 fuel cell prototype was evaluated using the PPO-22-3QA8F membrane as a separator to achieve a peak power density of 102 mW cm-2, which was nearly 3 times higher than that of the PPO-8-3QA membrane (38 mW cm-2) under the same operating conditions. Overall, the results of this study provide an efficient strategy to guide the architectural design of high-performance AEMs.

Rational Design Protocols to Tune the Morphology and Conductivity of Poly (arylene Alkylene)-Based Anion Exchange Membranes

Poly(olefin)-Based Anion Exchange Membranes Prepared Using Ziegler–Natta Polymerization

Poly (aryl Ether Ketone)/polymeric Ionic Liquid with Anisotropic Swelling Behavior for Anion Exchange Membranes

Tuning Polar Discrimination Between Side Chains to Improve the Performance of Anion Exchange Membranes

Dual-cation Comb-Shaped Anion Exchange Membranes: Structure, Morphology and Properties

Chain Architecture Dependence of Morphology and Water Transport in Poly(fluorene Alkylene)-Based Anion-Exchange Membranes

Simultaneous Enhancements of Conductivity and Stability for Anion Exchange Membranes (AEMs) through Precise Structure Design

In situ construction of interconnected ion transfer channels in anion-exchange membranes for fuel cell application

Boosting the performance of an anion exchange membrane by the formation of well-connected ion conducting channels

A Mechanically Robust Anion Exchange Membrane with High Hydroxide Conductivity

Facilitating ionic conduction for anion exchange membrane via employing star-shaped block copolymer

Tailoring the Nanophase-Separated Morphology of Anion Exchange Membrane by Embedding Aliphatic Chains of Different Lengths into Aromatic Main Chains

Engineering of Interconnected Ionic Channels in Polybenzimidazole Anion-Exchange Membranes

“Windmill” Shaped Branched Anion-Conducting Poly(aryl Piperidine) with Extra Molecular Interaction Sites As New Anion Exchange Membranes

Construction of Ion Conducting Channels by Embedding Hydrophilic Oligomers in Piperidine Functionalized Poly(2, 6-Dimethyl-1, 4-Phenylene Oxide) Membranes

Highly Conductive and Low Swelling of Fluorine-Free Poly(carbazolyl Aryl Piperidinium) Anion Exchange Membrane for Water Electrolyzer

Enhancing OH ̄ conduction in poly(arylene piperidinium) anion exchange membranes with hydrophobic perfluorinated side chains

Pyrrolidinium-functionalized Poly(arylene Ether Sulfone)s for Anion Exchange Membranes: Using Densely Concentrated Ionic Groups and Block Design to Improve Membrane Performance

Highly Conductive Anion Exchange Membranes with Long Flexible Multication Spacer

Imidazolium-Functionalized Poly(Arylene Ether Sulfone) Anion-Exchange Membranes Densely Grafted with Flexible Side Chains for Fuel Cells

Helical Configuration Channels Boost Performance in Anion Exchange Membranes