Abstract:Through the incorporation of phosphorus (P) as a third component, an in-situ formation of a magnetic phase with a nanotwin structure was achieved. The utilization of selective laser melting (SLM) enabled the synthesis of a Cu-Fe-P immiscible alloy that exhibits an integrated structure and function. The microstructure predominantly consists of a magnetic heterogeneous Fe-P-rich phase, comprising a mixture of Fe2P and a small quantity of Fe3P, which is distributed within the & epsilon;-Cu Cu-rich matrix in alternating "fiber -layer" and "particle-shape" forms. Additionally, the fibrous Fe2P phase exhibited precipitation of a-Fe, while the Fe-P-rich phase experienced the precipitation of high-density nanotwinned Cu (nt-Cu) particles. The microstructure density and structural characteristics of Cu-Fe-P immiscible alloys were enhanced through the adjustment of laser energy density, leading to improvements in their mechanical and magnetic prop-erties. It was observed that the microstructure density initially increased and then decreased with increasing laser energy density. The highest relative density of the Cu-Fe-P immiscible alloy microstructure (98%) was achieved at a laser energy density of 53 J/mm3. Furthermore, the influence of laser energy density on the mechanical and soft magnetic properties of Cu-Fe-P immiscible alloys was examined. The findings indicate that the mechanical and soft magnetic properties of these alloys are affected by the laser energy density. The findings indicate that the compact Cu-Fe-P immiscible alloys exhibit favorable compression mechanical properties and soft magnetic properties. Specifically, the ultimate compressive stress can reach 890.5 & PLUSMN; 20 MPa, while the failure strain can reach 20.5 & PLUSMN; 2%. Additionally, the coercivity is observed to be as low as 20.0 Oe, the magnetic saturation strength as high as 93.5 emu/g, and the residual magnetization at 1.1 emu/g.& COPY; 2023 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

Effect of Laser Energy Density on Microstructure and Properties of High Strength and Magnetic Cu-Fe-P Immiscible Alloys Fabricated by Laser Selective Melting

Effect of Laser Energy Density on Microstructure and Properties Cu–Fe–P Immiscible Alloys Fabricated by Laser Selective Melting: Heterogeneous and High Strength and Magnetic

Effect of Si Element and TiB2 Nucleating Agent on Microstructure and Magnetic Properties of Cu-based Immiscible Composites by Laser Melting Deposition

Effects of adding Cu on the microstructure and properties of in-situ alloyed Fe–Cr–Co permanent magnets by laser powder bed fusion

Amorphous alloy reinforced Cu-based immiscible coatings by laser melting deposition: Separation mechanism and corrosion behavior

In-situ Fe2P reinforced bulk Cu–Fe immiscible alloy with nanotwinned Cu produced by selective laser melting

Effect of Laser Energy Density on Surface Morphology, Microstructure, and Magnetic Properties of Selective Laser Melted Fe-3wt.% Si Alloys

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Effect of current on the tribological behavior of Cu-Fe-P immiscible alloy produced by laser powder bed fusion

Effect of Laser Energy Density on Phase Evolution in Laser Surface Melted As-Cast Zr–Cu Alloy

Mechanical Properties and Interfacial Characterization of Additive-Manufactured CuZrCr/CoCrMo Multi-Metals Fabricated by Powder Bed Fusion Using Pulsed Wave Laser

Laser powder bed fusion of copper matrix iron particle reinforced nanocomposite with high strength and high conductivity

Influence of Laser Process on the Porosity-Related Defects, Microstructure and Mechanical Properties for Selective Laser Melted AlSi10Mg Alloy

Effect of laser power on microstructures and properties of Al-4.82Mg-0.75Sc-0.49Mn-0.28Zr alloy fabricated by selective laser melting

Hierarchical microstructure and strengthening mechanism of Cu-36.8Fe alloy manufactured by selective laser melting

Microstructures and Mechanical Properties of CrMnFeCoNi High Entropy Alloys Fabricated Using Laser Metal Deposition Technique

Effects of Process Parameters on Microstructures and Tensile Properties of Laser Melting Deposited CrMnFeCoNi High Entropy Alloys

Revealing the Evolution of Microstructure and Mechanical Properties with Energy Density to Achieve High-Strength Ti-6wt%Cu Alloy by Laser Metal Deposition

Effect of Laser Irradiation and Tensile Stress on Microstructure and Magnetic Properties of Fe-Based Amorphous Alloys

Effect of Laser Energy Density on the Microstructure and Microhardness of Inconel 718 Alloy Fabricated by Selective Laser Melting

Effect of SLM Processing Parameters on Microstructures and Mechanical Properties of Al<sub>0.5</sub>CoCrFeNi High Entropy Alloys