Abstract:Through the incorporation of phosphorus (P) as a third component, an in-situ formation of a magnetic phase with a nanotwin structure was achieved. The utilization of selective laser melting (SLM) enabled the synthesis of a Cu-Fe-P immiscible alloy that exhibits an integrated structure and function. The microstructure predominantly consists of a magnetic heterogeneous Fe-P-rich phase, comprising a mixture of Fe2P and a small quantity of Fe3P, which is distributed within the & epsilon;-Cu Cu-rich matrix in alternating "fiber -layer" and "particle-shape" forms. Additionally, the fibrous Fe2P phase exhibited precipitation of a-Fe, while the Fe-P-rich phase experienced the precipitation of high-density nanotwinned Cu (nt-Cu) particles. The microstructure density and structural characteristics of Cu-Fe-P immiscible alloys were enhanced through the adjustment of laser energy density, leading to improvements in their mechanical and magnetic prop-erties. It was observed that the microstructure density initially increased and then decreased with increasing laser energy density. The highest relative density of the Cu-Fe-P immiscible alloy microstructure (98%) was achieved at a laser energy density of 53 J/mm3. Furthermore, the influence of laser energy density on the mechanical and soft magnetic properties of Cu-Fe-P immiscible alloys was examined. The findings indicate that the mechanical and soft magnetic properties of these alloys are affected by the laser energy density. The findings indicate that the compact Cu-Fe-P immiscible alloys exhibit favorable compression mechanical properties and soft magnetic properties. Specifically, the ultimate compressive stress can reach 890.5 & PLUSMN; 20 MPa, while the failure strain can reach 20.5 & PLUSMN; 2%. Additionally, the coercivity is observed to be as low as 20.0 Oe, the magnetic saturation strength as high as 93.5 emu/g, and the residual magnetization at 1.1 emu/g.& COPY; 2023 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

In-situ Fe2P reinforced bulk Cu–Fe immiscible alloy with nanotwinned Cu produced by selective laser melting

TiB2- and Fe2P with nanotwins-reinforced Cu-based immiscible composites fabricated by selective laser melting: Formation mechanism and wear behavior

Effect of Laser Energy Density on Microstructure and Properties Cu–Fe–P Immiscible Alloys Fabricated by Laser Selective Melting: Heterogeneous and High Strength and Magnetic

Effect of Laser Energy Density on Microstructure and Properties of High Strength and Magnetic Cu-Fe-P Immiscible Alloys Fabricated by Laser Selective Melting

Laser powder bed fusion of copper matrix iron particle reinforced nanocomposite with high strength and high conductivity

Hierarchical microstructure and strengthening mechanism of Cu-36.8Fe alloy manufactured by selective laser melting

Additive manufacturing of high strength copper alloy with heterogeneous grain structure through laser powder bed fusion

Amorphous alloy reinforced Cu-based immiscible coatings by laser melting deposition: Separation mechanism and corrosion behavior

Effect of Si Element and TiB2 Nucleating Agent on Microstructure and Magnetic Properties of Cu-based Immiscible Composites by Laser Melting Deposition

Achieving Novel Copper–steel Joints with a Combination of High Strength and Ductility Reinforced by In-Situ Fe-rich Particles

Processing and Microhardness of Bulk Cu-Fe Nanocomposites

Introduction of nanoprecipitation into supersaturated CoCrFeNiMo0.5 alloy prepared by laser-powder bed fusion via microstructure tailoring to achieve excellent properties

Nanotwins-containing microstructure and superior mechanical strength of a Cu‒9Al‒5Fe‒5Ni alloy additively manufactured by laser metal deposition

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Microstructure Twinning and Mechanical Properties of Laser Melted Cu-10Sn Alloy for High Strength and Plasticity

Laser powder bed fusion of a tungsten-nickel-ferrum alloy via in-situ alloying: Densification, microstructure, and mechanical properties

In-situ TiC x N y nanoparticle reinforced crack-free CoCrFeNi medium-entropy alloy matrix nanocomposites with high strength and ductility via laser powder bed fusion

Enhanced strength-ductility synergy in an ultra-strong copper alloy via coherent nanoprecipitates and stress-induced twinning

Laser powder bed fusion of in-situ amorphous oxide dispersion strengthened immiscible Cu-316 L bimetallic composite: Formation mechanism and current-carrying wear behavior

In Situ Alloyed Medium Entropy Alloy Fabricated by Laser Powder Bed Fusion: Microstructure and Cryogenic Performance

Development of Fe–P–C–Cu Immiscible Amorphous Alloys with Liquid Phase Separation