Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Modification to the Cellular Automata Model for Predicting Cracking Patterns of Masonry Walls

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Macro-Modeling of Reinforced Concrete Structural Walls: State-of-the-Art

Cohesive Cracking Simulation of Concrete Using Effective Modulus

Influence of constructional measurements on cracking of wall with small concrete hollow blocks

Research on Crack-Resisting Construction Design Method of Concrete Small Cavity Block Building Based on Temperature Effect

Simplified mechanical models for the seismic collapse performance prediction of unreinforced masonry structures

MODIFICATION ANALYSIS AND EXPERIMENTAL STUDY OF MOSONRY MORTAR

Simulation and Experimental Verification of the Non-Uniform Corrosion Cracking Process of Reinforced Mortar Specimen

State-of-the-art Development on ‘code for Design of Masonry Structures’

Analytical modeling of masonry load-bearing walls

Experimental Study on Lateral Resistance Behavior of Small Concrete Hollow Block Wall with Different Constructional Measures

Simulation and analysis of infilled-wall cracks' development by shrinkage using semi-discrete and whole type model

Modification of a macro model for RC structural walls with large openings

A block-based numerical strategy for modeling the dynamic out-of-plane behavior of unreinforced brick masonry walls

Numerical simulation of autoclaved aerated concrete masonry wall subjected to close-in explosion and the structural damage assessment

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

A robust computational strategy for failure prediction of masonry structures using an improved multi‐surface damage‐plastic based interface model

Comsol Simulations of Cracking in Point Loaded Masonry with Randomly Distributed Material Properties

An improved method for statistics estimation of out-of-plane load resistance of masonry walls using design-code models and mechanics-based finite element models

Explicit Approach for the In-Plane Cyclic Behaviors of Unreinforced Masonry Structures Using Finite Particle Method