Abstract:It is well known that welding produces thermal stresses which cause distortion of structures and residual stresses which influence buckling strength and brittle fracture strength of welded structures. Cold cracking of the weldment has beem investigated from a mechanical point of view with special attention paid to thermal stresses induced during the cooling stage of a welding thermal cycle.For a better analysis on these subjects, it is necessary to obtain more accurate information on the entire histories of stresses and strains to which the material is subjected during the process of welding. At the instant of welding, a limited portion of the welded joint such as the weldment and the base metal in its vicinity is heated to a very high temperature and therafetr cooled down to room temperature. The thermal cycle proceeds, the temperature distribution changes with time and the mechanical properties of the metals depend on temperature. In order to perform a more reliable analysis, the above mentioned factors should be taken into account. However, there are many difficulties in analysing theoretically practical models, including these effects, by classical methods, and there are only a few reports of their analysis based on simplified assumptions, such as regarding the problem as one dimensional problem or neglecting most of tempe-rature-dependent factors.The authors developed a method of theoretical analysis on this problem based on the finite element method, with consideration of the effects of changes in modulus of elasticity, yield stress and coefficient of expansion of the metal which are dependent on temperature under the assumption that problem is regarded as quasi-static, so that there is no interaction between temperature distribution and stress one. Accordingly, the temperature analysis is carried out independently before the stress analysis. As both analyses take incremental procedure, they can take into consideration of the effects of experience of the material before a stage at the following step of computation. if necessary, such as the rate of cooling on phase transformation, peak temperature on the mechanical properties, etc. in addition to the above mentioned temperature dependent properties. Examples of calculation given here are thermal stresses induced in butt welded joint under a moving electorode and local stresses and strains in RRC specimens during thermal cycle, and they show the usefulness of the method to general cases of welding.

Prediction of Temperature and Stress Fields in Beryllium Ring During Electron Beam Welding by Finite Element Analysis

Research on X-Ray Computer Tomography for Measuring Residual Stresses of Beryllium Weldment

Nonlinear Transient Analysis of Butt Welding Based on Finite Element Method

Microstructural analysis of the thermal fatigue tested Be/CuCrZr joint with artificial defects between Ti/Cu interlayers

Finite element analysis on electron beam brazing temperature and stresses of stainless steel radiator

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Simulation and analysis of electron beam welding residual stress in thin-walled high-temperature alloy aeroengine structures

Temperature Simulation of Aluminium Alloy Double-Arc Welding Process on Simplified Conditions

Effects of Welding Parameters on Weld Shape and Residual Stresses in Electron Beam Welded Ti2AlNb Alloy Joints

Numerical Simulation for Full-Penetration Electron Beam Welding of Ti2AlNb Alloy

Numerical Simulations of Temperature Fields During Electron Beam Welding Using the Double-Beam Technique

Measurements and computations of welding residual stresses in thick electron beam welded components

3D Finite Element Numerical Simulation of Residual Stresses on Electron Beam Welded BT20 Plates

Analysis of Thermal Elastic-Plastic Behavior of Metals during Welding by Finite Element Method

Prediction of temperature field and residual stress of oscillation laser welding of 316LN stainless steel

Simulation Analysis of Dynamic Process in Electron Beam Welding

Three-dimensional finite element analysis on welding residual stresses of construction steel

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

Finite element simulation of temperature field for TIG butt welding of thin plate

Analytical and FEM models for thermal analysis and residual stresses using wire arc-based welding and additive manufacturing of SUS304

Numerical Simulation of the Stress-Strain State of a PAW-MIG-Welded 1561 Aluminum Alloy Butt Joint Produced Under Different Process Modes